Ford 7.3L Power Stroke (1999-2003) :: Codes For Exhaust Pressure Circuit Valve / Intake Air Heater Control Circuit

I have an emissions test coming up. I have 3 P codes that I'd like to eliminate before then. I don't want to "fix" the issues they are telling me about. Just make the codes go away. I know why they're there I just need to get rid of them.

What I have coming up is:

P0475 Exhaust Pressure Circuit Valve (result of EBPV delete)
P0541 Intake air heater A circuit low (result of aih delete)
P0640 Intake air heater control circuit (also result of aih delete)

What resistors I'll need and where to put them in?

View 12 Replies

Ford Ranger / B-Series :: O2 Sensor Heater Circuit Malfunction / Evaporative Emission Control System Detected Large Leak

I have some codes on my ranger 2000 here goes

P0141: o2 sensor heater circuit malfonction (bank 2 sensor 2 )
P0455: evaporative emission control system detected (large leak)

Now I will need to get that fixed cause I don't know where to look and what to look for ... For the leak I know there is a big crack on the plastic where the gas lid is could that be it ?

View 2 Replies

Ford Ranger / B-Series :: 1999 - P0135 O2 Sensor Heater Circuit (Bank 1 Sensor 1)

1999 Ranger 4x4 4.0 - P0135 O2 Sensor Heater Circuit (Bank 1 Sensor 1)

I have replaced the 02 Sensor, Passenger Side (Pre-Cat), with a Motorcraft DY831...

I reset the Check Engine fault codes, and took it out for a 50 mile journey... Check Engine light is back on, with the same exact code... What next?

I understand that it may be a fuse, and/or it may be a short in the wiring... Exactly how to test the wiring from the connector at the 02 Sensor all the way back to wherever I need to test?

I really need detailed directions, like wire colors, voltage required, or ohms, or whatever is included in this process...

View 5 Replies

Ford Ranger / B-Series :: 1997 - Heater Blower Motor Resistor Rusted

I am not great with electrical but can manage. Here's the deal, Ihave a 1997 ford ranger 2wd 2.3L 5spd with a/c 233,000 miles i just replaced the heater blower motor resistor as the old one was rusted bad as was the pig tail going to it bad that one of the terminals broke off and was rusted in the harness so i replaced the plug as well problem is i still have no fan if i jump it it works but have no power at the plug for resistor or motor and no power at the switch inside the truck I do have power to one terminal where the relay plugs in, where to look next?

View 14 Replies

Ford - Explorer :: Check Engine Light Is On For Codes P0161 And P0155 - O2 Heater Circuit Sensor Is Bad

I have a 1996 Ford Explorer Eddie Bauer Edition 5.0, the check engine light is on and my code reader gives P0161 and P0155 both stating that the O2 heater circuit sensor is bad. I replaced all 4 of the O2 sensors in the truck, cleared the codes but they still keep coming back. I have tried for a few days now to find something online similar to this but have had no luck. I am not sure what else to do.

View 1 Replies

Lexus GX 2004-09 :: Fault Codes P0037 And P0057 - Oxygen Sensor Heater Control Circuit Low

What can be done regarding these faults? P0037 and P0057

Description:
Oxygen Sensor Heater Control Circuit Low (Bank 1, Sensor 2)
Oxygen Sensor Heater Control Circuit Low (Bank 2, Sensor 2)

The catalytic converters have been removed but the fault was present before that anyway. All I want is the VSC function to work again and the lights to go off. I have heard you can put dummy sensors in.

View 3 Replies

Ford F-150 - 1997-2003 :: Code P0161 Came Up - 2nd Bank Downstream Heater Circuit Fault

Just started the truck after not running for a few weeks and drove around fine. Looked down and suddenly a CEL was indicated. Checked it with my Edge Evolution diagnostic mode and Code P0161 came up 2nd bank downstream heater circuit fault. I've also have an exhaust leak in the right passenger side exhaust manifold for about the last year. I've been waiting to install my newer 03' used engine when time and funds permit.

View 3 Replies

Ford F-150 - 1997-2003 :: Vacuum Leak - Error Codes Indicating Bad O2 Sensors

I am having problems with a 2003 Ford F 150 with a 4.2 L V6. The problem is that it is giving me code errors that would indicate bad O2 sensors. I replaced both the upper and lower O2 sensors, and still I get the same codes. I was told by the mechanic with the computer reader that this usually means a bad vacuum seal. He suggested looking for bad hoses, but did not offer much more than that. How to proceed?

View 2 Replies

Ford Ranger / B-Series :: Brake And ABS Lights On - Open / Grounded Valve Reset Circuit

1993 ford ranger xlt. Auto trans 4.0 L ... Brake and ABS lights are on. Fluid level is good and connector on the master is tight. Just randomly came on. No difference in brakes. I jumped it and it flashed a code 4. "Open/grounded valve reset circuit". Cant seem to find much on it.

View 1 Replies

Ford Ranger / B-Series :: 1998 - Code P1405 - DPFE Sensor Circuit Upstream Hose

I just bought a '98 Ranger 2.5l 2wd. After driving it for a week or so I got a P1405 Code. After a quick google search I got :

P1405 Ford - DPFE Sensor Circuit Upstream Hose

Possible Causes: - Faulty Differential Pressure Feedback Electronic (DPFE) sensor (EGR pressure sensor)

- Plugged or damaged EGR tube
- Differential Pressure Feedback Electronic (DPFE) sensor harness is open or shorted
- Differential Pressure Feedback Electronic (DPFE) sensor circuit poor electrical connection

Now, I have done my research between forums and youtube and have found this EGR system to be quite. I've gone ahead and replaced my DPEF. I took an air hose and blew out all the small lines coming into the DPEF. I still have the engine light. My next move is to get a volt meter and see if I'm getting power to the sensor.

My question is about this particular code and is it possible I need to look farther into this EGR system (EGR Valve, EGR Hose, etc.)

View 5 Replies

Accord :: 1997 LX 2.2L - Codes P0135 And P0141 / Changed Oxygen O2 Sensors

I changed both oxygen sensors yesterday on my 1997 Accord.

Check Engine Light was on and I was getting codes:

P0135 - O2 Sensor Heater Malfunction Bank 1 Sensor 1
P0141 - O2 Sensor Heater Malfunction Bank 1 Sensor 2

Also, after clearing the codes, if I started the vehicle the codes would come on instantly. So it wasn't some kind of flaky electrical issue, it was consistent.

View 1 Replies

Ford Ranger / B-Series :: Heater Lever Stuck?

, my trucks heat selector lever, that controls the temperature in my truck, is stuck in the cold setting. by stuck I mean, I can try to move it, but it wont budge more than about 1/16" and no more. its really frustrating because of the cold weather here, and I want to have SOME heat in my truck without a bonfire to get it.

View 6 Replies

Ford Ranger / B-Series :: 1999 - Heater Fan Not Working?

My wife's 99 Ranger's heater fan is not working. It was working off and on until now. The fuse is fine. I went out this morning and tested the blower motor for power in --had voltage. Assuming the motor was bad, I pulled it. Before wasting $ and a trip to town, I bench tested it --it works. Now my question: what do I do next?

View 6 Replies

Ford Ranger / B-Series :: 1996 - No Heater Control

I seen on this site awhile ago something about a fix for the heater control door, I have a 1996 Ranger and all I have is Hot heat and cannot cool it down with the temperature control.

View 2 Replies

Ford Ranger / B-Series :: 2005 - Heater Not Blowing Hot Air?

Got a 2005 V6 Ranger with low mileage. Having a heater problem. We've replaced the thermostat, heater core, flushed the system twice, burped it to get the air out and replaced the hot water valve. The heater works for a few days then it goes cool: not cold. Adjusting "Temp" will make the temp decrease but it will not return to hot air?

View 2 Replies

Ford Ranger / B-Series :: 2004 - Heater Won't Warm Up While Idling

My '04 Ranger has over 240k on the odometer. Runs great and has never given me any issues. Everything checks out OK - all the fluids, filters, and whatnot are in good shape. No CEL or any other indication that anything is wrong (except for maybe the IAC valve and clutch slave.)

I've noticed, though, that when I fire it up in the mornings to let it warm up while I scrape the ice and snow off the windows, the heat/defrost will not blow warm air. It doesn't matter how long I let it sit, it will only blow ambient air through the ducts.

When I get going down the road, however, the heat kicks in, after a bit, and works very well!

I've not found anything that would indicate an issue with the blend door or any other component and this is the first vehicle I've had that did this.

Is it normal for a 4.0 SOHC Ranger to do this? Or is there something I'm missing?... It's not really that big of a deal, but I do find it a bit odd that it would do this.

I mentioned the IAC above - I think it's "sticking" every once in a while and, when it does, I'll hear a loud "thump" right before it idles down to around 1k rpm. I can't see how this would affect the heat, though...

View 14 Replies

Ford Ranger / B-Series :: 1994 - Got Codes 218 And 998?

Working on a friends 94 ranger, 2.3 L with codes 218 and 998. Chiltons manual does not even show this code. Code is for Loss of Ignition Diagnostic Monitor (IDM)/left side. What exactly is this? Can't find anything that explains the IDM.

998 means a hard fault.

View 10 Replies

Ford Ranger / B-Series :: 1996 - Heater / AC Blower Only Works When Warm Out

I have a 1996 Ranger that the Heater/AC blower only works when the outside air temp is above 45 degrees. I have replaced the relay, and the blower motor resistor. What could be causing this?

View 3 Replies

Ford Ranger / B-Series :: 1989 - Heater Hose Leaking Around Behind The Valve Cover

Found a tee on the heater hose leaks when it warms up. Appears the PO had noticed it but put a hose over it and now is leaking around behind the valve cover. This is a hard plastic line around 5/16. No online parts show it as being available. Is there a fix for this ?

I would bet several others have had this problem as it lays right on top of the flange of the valve cover where I think it would rub a hole pretty quick.

1989 Ranger 4X4 4 cylinder....

View 3 Replies