Ford Ranger / B-Series :: 1999 - CEL On - A/C Stopped Working?
I have a 1999 Ranger 4x4 4.0 5 speed step side...in Jalapeno no less. Anyway, for the past 5 years or so the check engine light has been on. When it came on I did nothing because nothing seemed to change and I was too broke to fix it anyway. Well, just lately the check engine light has started to flicker or go out completely.
When this happens the truck seems sluggish and the A/C will stop working. As long as the check engine light is ON the truck runs like it always has, when it goes off the issues start. If I am stopped with the clutch depressed the idle will drop down to 500 rpms or so.
Kinda hoping it is something I can fix or at least learn about so I can have an intelligent conversation with a mechanic.
Ford Ranger / B-Series :: 1999 - P0135 O2 Sensor Heater Circuit (Bank 1 Sensor 1)
1999 Ranger 4x4 4.0 - P0135 O2 Sensor Heater Circuit (Bank 1 Sensor 1)
I have replaced the 02 Sensor, Passenger Side (Pre-Cat), with a Motorcraft DY831...
I reset the Check Engine fault codes, and took it out for a 50 mile journey... Check Engine light is back on, with the same exact code... What next?
I understand that it may be a fuse, and/or it may be a short in the wiring... Exactly how to test the wiring from the connector at the 02 Sensor all the way back to wherever I need to test?
I really need detailed directions, like wire colors, voltage required, or ohms, or whatever is included in this process...
Ford Ranger / B-Series :: 1999 - Gas / Temp Gauges Not Working
Just purchased this truck and noticed the gas and temp guages neither work. Where do I start/ How about fuse box?
View 5 RepliesFord Ranger / B-Series :: 1999 - Trailer Lights Stopped Working?
My brother has a 99 ranger with the 4.0 engine and factory tow package. After installing a rebuilt engine the brake lights do not work and the turn signals will blink both sides like flashers. Lights on the truck work fine. What connections may be hooked up wrong or where to start looking for the problem.
View 3 RepliesFord Ranger / B-Series :: 1999 - 4 Wheel Drive Quit Working - Wiring Diagram?
My son has a 99 ranger and the 4 wheel drive quit working. Traced it to the front hubs not getting vacuum. If I jump around the vacuum solenoid(not sure if that's what it's called), the 4 wheel drive works. Looking for a wiring diagram that shows how this is supposed to work electrically?
View 5 RepliesFord Ranger / B-Series :: Heater Lever Stuck?
, my trucks heat selector lever, that controls the temperature in my truck, is stuck in the cold setting. by stuck I mean, I can try to move it, but it wont budge more than about 1/16" and no more. its really frustrating because of the cold weather here, and I want to have SOME heat in my truck without a bonfire to get it.
View 6 RepliesFord Ranger / B-Series :: 1996 - No Heater Control
I seen on this site awhile ago something about a fix for the heater control door, I have a 1996 Ranger and all I have is Hot heat and cannot cool it down with the temperature control.
View 2 RepliesFord Ranger / B-Series :: 2005 - Heater Not Blowing Hot Air?
Got a 2005 V6 Ranger with low mileage. Having a heater problem. We've replaced the thermostat, heater core, flushed the system twice, burped it to get the air out and replaced the hot water valve. The heater works for a few days then it goes cool: not cold. Adjusting "Temp" will make the temp decrease but it will not return to hot air?
View 2 RepliesFord Ranger / B-Series :: 2004 - Heater Won't Warm Up While Idling
My '04 Ranger has over 240k on the odometer. Runs great and has never given me any issues. Everything checks out OK - all the fluids, filters, and whatnot are in good shape. No CEL or any other indication that anything is wrong (except for maybe the IAC valve and clutch slave.)
I've noticed, though, that when I fire it up in the mornings to let it warm up while I scrape the ice and snow off the windows, the heat/defrost will not blow warm air. It doesn't matter how long I let it sit, it will only blow ambient air through the ducts.
When I get going down the road, however, the heat kicks in, after a bit, and works very well!
I've not found anything that would indicate an issue with the blend door or any other component and this is the first vehicle I've had that did this.
Is it normal for a 4.0 SOHC Ranger to do this? Or is there something I'm missing?... It's not really that big of a deal, but I do find it a bit odd that it would do this.
I mentioned the IAC above - I think it's "sticking" every once in a while and, when it does, I'll hear a loud "thump" right before it idles down to around 1k rpm. I can't see how this would affect the heat, though...
Ford Ranger / B-Series :: 1997 - O2 Heater Circuit Codes For All 3 Sensors
1997 2wd, 4.0 - As you can guess it runs pretty bad at idle. It has O2 heater circuit codes for all 3 sensors. I'm leaning towards the ECM because the 2 heater wires are both hot with the key on. I unplugged the computer and turned the key on and just one wire is hot. Looks like the ecm is supposed to ground the wire to turn the heater on, but it's going hot instead?
View 14 RepliesFord Ranger / B-Series :: 1996 - Heater / AC Blower Only Works When Warm Out
I have a 1996 Ranger that the Heater/AC blower only works when the outside air temp is above 45 degrees. I have replaced the relay, and the blower motor resistor. What could be causing this?
View 3 RepliesFord Ranger / B-Series :: 1999 - Electrical Malfunction - Burning Smell - Hard Downshifting - Power Window Quit Working?
I'm having some issues with my 99 ranger. It all started on my way to work one afternoon. Going down the road I started to smell some type of electrical burning smell. I looked at my instrument cluster and seen a trail of smoke come up between the steering wheel and ins cluster from under and gear selector covers. After that the O/D off light started flashing and downshifting hard. My pwr windows and dome light also quit working. Checked fuse #26 and all my fuses before going into work that afternoon, all of them were good and none blown. After shift was over that night going home I needed to use the wipers and they wouldn't work either. Also noticed then that my speedo, odometer and trip odometer not working. I've pulled my dash and steering covers off trying to find or see anything but nothing yet.
View 14 RepliesFord Ranger / B-Series :: 1989 - Heater Hose Leaking Around Behind The Valve Cover
Found a tee on the heater hose leaks when it warms up. Appears the PO had noticed it but put a hose over it and now is leaking around behind the valve cover. This is a hard plastic line around 5/16. No online parts show it as being available. Is there a fix for this ?
I would bet several others have had this problem as it lays right on top of the flange of the valve cover where I think it would rub a hole pretty quick.
1989 Ranger 4X4 4 cylinder....
Ford Ranger / B-Series :: 1997 - Heater Blower Motor Resistor Rusted
I am not great with electrical but can manage. Here's the deal, Ihave a 1997 ford ranger 2wd 2.3L 5spd with a/c 233,000 miles i just replaced the heater blower motor resistor as the old one was rusted bad as was the pig tail going to it bad that one of the terminals broke off and was rusted in the harness so i replaced the plug as well problem is i still have no fan if i jump it it works but have no power at the plug for resistor or motor and no power at the switch inside the truck I do have power to one terminal where the relay plugs in, where to look next?
View 14 RepliesFord Ranger / B-Series :: 1985 - Heater Blower Sounds Like A Legion Of Demons
When I turn on my heater full blast the most god awful squealing commences. Where to start spraying the grease?
View 10 RepliesFord Ranger / B-Series :: 2003 - Heater Vent Selector Stuck On Defrost
There is always something.... I just drove my girlfriend's new 2003 ranger edge home from the seller. Real nice truck. I noticed the heater selector doesn't change the air flow. It is on full blast for the defrosters, and is also trickling out of the floor and dash vents. No matter where you put the selector, thats the only place the air comes out.
The temp control seem to work OK, when you turn it on cold, you get cold air and visa versa. Even on AC and MAx AC... air out the defrosters. It's cold when you turn the temp control to cold.
I did some searching here and gather some info on checking the vac lines etc. Everything looks in place but one detail. The vac ball under the hood under the air box has 2 ports on the front end, and only one grey line going into it. The other port has what looks like a rubber boot and part of a very short vac line broken off it.
I looked, I cant find any loose vac lines. I'd like to know if this second port is suppose to have a second line on it, and where does it go? What color is it? Is this the reason the vent selector isnt working?
Ford Ranger / B-Series :: New Heater Core / Blower Motor And Resistor Still No Heat?
with a new heater core, new blower motor, and new resistor and no heat, what would be the problem? gonna check the thermostat tomorrow.
View 2 RepliesFord Ranger / B-Series :: O2 Sensor Heater Circuit Malfunction / Evaporative Emission Control System Detected Large Leak
I have some codes on my ranger 2000 here goes
P0141: o2 sensor heater circuit malfonction (bank 2 sensor 2 )
P0455: evaporative emission control system detected (large leak)
Now I will need to get that fixed cause I don't know where to look and what to look for ... For the leak I know there is a big crack on the plastic where the gas lid is could that be it ?
Ford Ranger / B-Series :: ABS Light And Speedometer Not Working
I have the infamous ABS light & speedo not working on my 2000 Ranger. I replaced the ABS Speed sensor on the rear diff as has been suggested on many posts, but it didn't solve the problem. Did I get a bad part or is there something else I should go after?
View 7 Replies