Ford Ranger / B-Series :: 1997 - Engine Will Not Reach Proper Operating Temperature
I have a 97 Ranger 2.3 standard shift, No A/C, a pretty simple Ranger with 158,000 miles. About a month ago while do some checking around under the hood I noticed my coolant overflow tank was empty, so I filled it up to the proper level with some anti-freeze mixture. Thinking if the system was low on anti-freeze it would suck what it needed from the recovery tank, wrong! About two weeks ago I noticed that my temperature gauge was NOT registering in its normal position and was considerably lower towards the Cold mark. Heat coming out of the heater was normal.
I opened the radiator cap and everything looked okay. After a few days this would not go away and replaced the thermostat thinking the thermostat was stuck in the open position, wrong again! I burped the system by letting the engine run with the radiator cap off and filled the radiator with anti-freeze mixture every time some of the air was expelled. I did this for a few days and noticed that the engine would not reach normal operating temperature at idle speed! I had to put something on the gas pedal to increase idle speed so the engine would get hot, this is not normal. Finally I got to a point where the radiator would not take anymore anti-freeze mixture, but the problem still exists.
Two things I noticed that will get the engine temperature up to normal, engine speed (RPM's) and not having the heater on. Let me explain, at normal idle the engine will not reach its proper temperature, but when driving down the highway the temperature goes up to normal (about halfway on the scale) no matter if the heat is on or not. When stopped at a light or just idling I can watch the gauge slowly go down towards the cold mark, if I turn off the heater it takes longer to go down to cold. I do know the heater fan is cooling the coolant to a degree (no pun intended), but it shouldn't cool it so much as to make the temperature drop so dramatically. Okay, heater off, riding down the highway, everything normal, come to a stop and idle temperature starts falling slowly, but when I turn on the heater the temperature starts falling faster.
My diagnosis: I have no leaks of anti-freeze, checked and re-checked. I have no symptoms of a blown head gasket, no milky white appearance on dip stick indicating anti-freeze mixing with engine oil, no clouds of white smoke coming out of exhaust, checked tail pipe for anti-freeze, none found, no loss of power and no loss of gas mileage. I changed the thermostat, like I said. Do not think it could be the radiator pressure cap, normally if the cap goes bad the system will have no pressure and the engine will overheat, the opposite of the problem. Water pump, normally if the water pumps goes the coolant will not circulate through engine and will over heat, again, not the problem I am having. Could it be:
1. A long shot, I bought a defective thermostat and it is still staying open.
2. The temperature sending unit has gone bad, very improbable since it does register the correct temperature when truck is moving down the highway.
3. The coolant is spent, again unlikely, it has been in the engine only for about 3 years and still looks clean and green.
4. Have to have a cylinder pressure check to determine actually if the head gasket is really blown or not, which I doubt.
My conclusion is that I still have a huge air lock somewhere in the system and the engine is still not completely filled with coolant and when the rpm's drop not enough hot coolant is reaching the temperature gauge sending unit, but if that much coolant is not in the system, why am I still getting lots of heat blowing from the heater? The vehicles cooling system is not that complicated and there are few parts involved in its proper operation, I think I have covered them all, but somewhere I am missing something to pin point my problem.
Ford Ranger / B-Series :: 1997 - Water Temp Gauge Does Not Work
Water temperature gauge doesn't work. Assumed the problem was the sensor so bought a new one. Installed it, still nothing registering on the gauge after I know the water is heated up (drove it for 45 minutes, heater blowing hot).
So crossed the ground on the sensor and the gauge shot to the top so gauge is working.
Pulled wiring diagram and that sensor is SUPPOSED to register 79ohms for cold and 8 ohms for hot.. So bought a 10ohm resistor from radio shack and attached the water temp lead to it and the gauge read correctly about 1/8 inch from the H mark on gauge. This confirmed for me that gauge is not at fault.
Next I attached the ohmmeter to the sensor itself, boiled some water, placed the sensor tip into it and it read 86 ohms, in freshly boiled water! So at boiling the sensor isn't anywhere near to tripping the gauge to even start reading cold! So I tested the old sensor that I was replacing and in boiling water it shows 94 ohms?
What am I doing wrong, is there an assumption I am making here in error? I want to conclude the new sensor is bad, but the old sensor reads nearly the same reading under same conditions.So yes maybe they are BOTH bad but that seems to be pushing probability.
If it matters this sensor is the type that is inline from radiator to heater core, not the type that is in the engine block, at some point ford changed their sensor setup but didn't change the schematic drawing. Which doesn't matter the only difference is the one in-line has a ground wire to it rather then grounding off the engine block.
Vehicle is a 97 Ford Ranger with the 2.0 liter engine.
Ford F-150 - 1997-2003 :: Barely Runs / Stumbling And Shaking / Got P0340 Code?
The vehicle has 160,000 miles and had been running great. I pulled into traffic, put the petal to the floor, and it started stumbling and shaking. I pulled into the parking lot where I was going and expected it to die but it maintained idle but shaking real good. When I started it back up the SES light came on. I was able to coax it home but there was no acceleration, wouldn't go over 40 mph, and was still shaking bad.
I used my code reader and got the code P0340, camshaft position sensor. I replaced the sensor but it is still doing the same thing and still showing the code. It will start if I push the gas while cranking but it won't rev over 2K. I am thinking it jumped timing but most of the threads I read say they have never seen this on these engines. I want to get some opinions before I start removing the timing chain cover.
Ford Ranger / B-Series :: Barely Accelerating From A Stop Light At 2k RPM - Horrible Gas Mileage
I got my b2500/ranger a couple of months ago and I've had very poor gas mileage. I replaced the air filter, changed the plugs, no luck. The truck has 169,000 miles. I haven't checked my exact gas mileage but from what i am seeing its horrible. I filled it up last night, not completely full but really close the full marker. In the morning i drove to school (7 miles) drove home, so 14 miles. Then i had to go back out by my school to pay back a friend. All in all about 28 miles. This cost me a little more than a quarter of a tank. The 2.5l has a 16 gallon fuel tank, so if my calculations are correct im getting about 8 miles to the gallon. I also took it the consideration that it was a half gallon from full.
And it wasn't just past below a quarter to full it was 3/4 of the way to a quarter from full. I know that i didn't test the mpgs "properly" but i think its close enough to draw a conclusion from. And keep in mind its not a 4.0, its a 2.5! Although i do think the engines size contributes to the mpgs because it takes ALOT to accelerate in this truck. At 2k rpm im barely accelerating from a stop light. And on the highway my engine stays a 2500 rpm doing 60-65. I am really hoping I can fix this because I don't want to drive around in a civic. Plus I need a truck for scrapping which is how I pay for gas as i am 17 and jobs are scarce. Also I know about cleaning the MAF butit has tamper proof torx on it which i do not have the tools to remove. I think it could also be the o2 sensors.
Ford Ranger / B-Series :: 1988 - Transmission Fluid Leaking Badly / Truck Barely Moves
1988 ranger, its a automatic 4x4 v6 and is leaking tranny fluid real bad. Truck barley moves because fluid comes straight out...
View 1 RepliesNissan - Altima :: 1997 GXE Stalling When Engine Warmed Up To Normal Operating Temp
I've got a 1997 Nissan Altima (automatic, GXE). Recently it has started stalling. Usually this happens when the engine has warmed up to normal operating temperature (though last night it happened when the engine had just started).
Usually when it stalls it will start right back up, but sometimes it takes a few minutes. Sometimes it will start back up and die right away, other times it will turn over and over but not start. After a few minutes it will start back up. Sometimes it will stall momentarily and then restart right away, but not usually.
The rest of the time the car runs smooth as ever, no surging, no stalling, no erratic idling, no sputtering or anything. Usually the check engine light will come on after a stall, but I get a "no code" code when I check.
This started about two weeks ago, it did it once on a Saturday and then didn't do it again until Wednesday. Since then it has happened at least once a day, and yesterday it happened a lot while I was driving home, but not at all when I headed to work. Today it was fine for about 15 minutes and then started doing it a lot, but the last 3 or 4 miles it was fine again.
What may be the problem? I'm going to check the MAF and throttle position sensors, though I would assume if they were malfunctioning I'd either have more symptoms or I'd be getting a code.
Ford Ranger / B-Series :: 2001 V6 Only Runs On 2 Or 3 Cylinders
My 2001 V6 Ford Ranger Edge has 124, 000 miles and always ran very well, Shortly after a minimal attempt to pull a vehicle out of a ditch the vehicle began to run poorly. This may be coincidental as problem did not begin straight away. The engine refused to start at first but now appears to run on 2 or 3 cylinders. I have checked AND CONFIRMED the following:
Spark at all cylinders
Fuel filter replaced
Fuel pump checked
Fuel pressure 56 psi at schrader valve on fuel rail
Fuel inertia cut off valve checked
E_Z start sprayed in feed horn did nothing
I hope to avoid towing it to the dealer,as I recently had a very negative experience doing this with the Honda dealer..
Ford Ranger / B-Series :: 2008 - Runs Rough With No Power
I just changed the plugs and wires on my 2008 Ranger 3L. Now it runs rough with no power. It was fine before I did the work but I thought I should change the plugs at 215000KM. I used Ford wires but unfortunately I used Bosh platinum plugs and now think I will change to Ford plugs. Do you think the Bosch plugs would be that bad for the Ranger? What is the belt tensioner torx size? I had to move the A/C compressor over to get the #4 plug but had a very hard time trying to loosen the belt.
View 7 RepliesFord Ranger / B-Series :: 1986 - Starts And Runs Rough / Bad Misfire
My pops has a 86 ranger with a 2.9. And what its been doing is, it will start up just fine then u give it a minute and itll start to run very rough like a bad miss fire, then if he revs it up for a bit. It will clear out and then run just fine until he starts it up again and it seems to do it more the colder it gets and it smells very rich. Iv checked the injectors and there fine, what other things could it be ? O2 sensors oorrr
View 5 RepliesFord Ranger / B-Series :: Runs Rough For About A Minute After Engine Started When Cold
This has been an ongoing issue for about a month. When I start the engine after it has been sitting and is cold it runs ruff for about a minute then smooths out and runs fine. I pulled a P0304 code (cyl.4 missfire) but I do not get a CEL.
I checked the plugs and they were ok but I changed them and the wires anyway as it just turned 50k and the plugs were original. I could live with a little cold ruff idle but the code throwing bothers me. The truck is a 2000 xlt 4x with auto trans. and 4.0 engine. This is my second 4.0 ranger but I have only had it for about 6 months.
Ford Ranger / B-Series :: 1995 - Overheats And Engine Runs Full Throttle
My 1995 ranger was running just fine then today overheats in five minutes and then runs at very high rpms, has 2yr old water pump new tstat don't think head is blown no water in oil no white smoke no water on the oil cap, I haven't check the plugs for water, stated raining no garage, when engine is cold starts runs fine,but when it gets hot its like a train...
View 5 RepliesFord Ranger / B-Series :: 1999 - Runs Rough At Start Up / Hesitate For The First 300 Feet Or So
I am working with a friend on his 99 Ranger with a 4.0 . When first started it will idle rough and hesitate for the first 300 feet or so, and then clear up and run smooth the rest of the day. If he lets it set for 6 or more hours it will repeat the problem. He has taken it to a local Ford dealer and they have replaced spark plugs, plug wires, coil pack, cleaned the throttle body, checked the air idle motor and passage.
He has had it to the dealer 3 times and their latest plan is to pull the heads @ a cost of 1500.00 to start. Since it runs well, no coolant in oil or oil in coolant nor loss of either fluid, I couldn't figure why they want to pull the heads.
To date it has not thrown a code, I ran it on a New Generation Star tester and cannot find a code. The truck runs great after the first intial start up and does not give any signs of cutting out or lack of power. My guess is it is losing fuel pressure overnight and is taking a while to reprime. Original fuel pump and 160K miles. Will do a fuel pressure test this weekend.
Ford Ranger / B-Series :: 1988 V6 Starts And Runs But Shuddering - Cylinder Not Firing?
'88 Ranger 2.9L V6 starts and runs but shuddering. Most noticeable when shifting and revving the engine. Will a dead cylinder cause this? How do I check?
View 2 RepliesGrand Prix :: Overheating But Temp Gauge Not Going Above Normal Operating Temp
I have a 2004 Grand Prix and it is displaying the symptoms of overheating but the temp gauge is not going above normal operating temp. I replaced the thermostat twice, and after driving for about 10-20 mins coolant comes out of the overflow. I'm at a loss, I'm thinking temp sensor(?) But I don't want to keep throwing unnecessary money into it. The fans work fine, the heater blows as it should.
View 8 RepliesFord Ranger / B-Series :: 1992 - Engine Starts And Runs Couple Of Seconds Then Shuts Down
I have a '92 Ranger with a 2.3 liter engine. She starts and runs a couple of seconds and shuts down. I'm thinking maybe a fuel pump is not putting out thepressure needed. Gotta go to work tomorrow and gotta get the truck running today.
View 2 RepliesFord Ranger / B-Series :: 1986 - Stalls / Idles Or Runs Roughly And Will Miss Erratically
I have a really nice 1986 Ranger XLT with a 2.9 V6 (injected) and OD Automatic with about 135k miles. I've had the truck for over ten years and have been pretty happy with it. I'm still trying to correct a couple of nuisance items:
1. Sometimes it runs smoothly, and at others it has a rough idle, and once in a while it will even stall. Before it stalls, it idles or runs roughly, and will miss erratically. When it quits, it does not fade out like it is running low on gas; it quits suddenly, like the ignition is turned off. If I am driving at highway speeds, sometimes it will buck as it misses, and sometimes stalls out. But it always starts up right away afterwards. This does not happen often, but when it does, it happens several times over hours or days, and then goes away by itself for months, even years, and then comes back for another round.
I was hoping whatever was wrong would totally fail, but it has been several years and is not getting better, nor worse. Fuel mileage varies, too, from 16 to high 20's MPG. I have new low- and high-pressure fuel pumps (dual tanks), new gas and air filters, checked all the electrical connections, put in a new ignition switch, new O2 sensor, Air Flow sensor, EGR, replaced all the vacuum lines, new battery and cables, new starter, all new electrical relays, fuel pressure regulators, new fuel pump inertia switch, tuned up engine (incl. wires, cap, rotor, ign module, plugs and timing), and cleaned out the already sparkling-clean tanks.
2. My oil pressure will drop at idle to low-normal when the engine is warm. It never goes to below Normal on the gauge. I have replaced the gauge, sending unit, and oil pump. This is a long-term issue, and is not getting any better or worse.
Ford Ranger / B-Series :: Temp Gauge Hardly Moves At All
I have a 94 Ford Ranger, 2WD, 5-Speed, with 2.3 engine. My temp gauge hardly moves at all... It actually appears as if it doesn't move it you don't pay close attention and were to just glance at it. I'm thinking it is most likely the temp sensor that is on the engine block as I understand there is also one that is in the line that controls the fans for the radiator. Am I approaching this in the right direction or is there something else I might need to do?
View 3 RepliesFord - Ranger :: 1997 Runs Lean And Dies
1997 ranger 3.0 auto.. took it to a shop to have some work done. trans fluid valve covers leaking. had no real problems with the truck.
now, first start in the AM and only them, it runs lean and dies. second start Ok rest of the starts during the day OK ...
replaced ICV, tosses no codes. fuel pressure Ok ...
Ford Ranger / B-Series :: 1994 - Idles Rough / Stalls When Cold But Runs Great When Warm
I have a huge problem. My 94 ranger 2.3L 5 speed manual transmission, has problems with idoling while it's cold, has no power going uphill and stalls when I slow down to stop. This is all after putting a new motor in. The old one was running ok with 310,000 but lagging bad. I figured with the driving I do, a new motor wouldn't be a bad thing. Boy, was I wrong. It has been a nightmare. But once the truck is up to operating temperature, it runs so smooth you wouldn't think there was a problem. But let it cool off, restart, and boom! There it is. We have changed so many parts and sensors with absolutely no change to the original problem. It's very frustrating. I just can't let this problem win. I will figure it out.
View 13 Replies