Ford Ranger / B-Series :: 1992 4.0 Refuses To Start
I am the owner of a 1992 ford ranger 4.0 that refuses to start. She turns over, but theres no pressure coming out of the fuel rack/valve. Might be the fuel pump but it started with a little boost about a month ago and now nothing. Head gasket and transmission have been tuned up as well! I've also checked the power distribution box, and spark plugs both seem to be doing thier job! What am i missing?!
View 2 RepliesFord Ranger / B-Series :: 1992 - Turns But Will Not Start / No Spark
My Ranger was running great when suddenly on the highway it just died. I towed it to local nationally known brake/ muffler shop where a good friend is the manager. He narrowed it down (guessed in my opinion) to no spark and no fuel. He thinks it could be the crank sensor, the fuel pump or the ignition module. Is there any way to pinpoint the problem without replacing parts? It will sometimes start and run for about 2 seconds before shutting off. It will not repeat this unless it sits for a day or two. I am not sure if there are different 2.3 engines available but mine is fuel injection and has two sets of spark plugs and wires.
View 9 RepliesFord Ranger / B-Series :: 1992 - Hard Start Almost Every Time
I'm working on a 1992 ranger with the 2.3l. Hard start almost every time, sometimes have to hold throttle open sometimes not. Won't start at all this morning. When it does finally start it takes a while for it to start firing on the intake side plugs. Haven't had time to check fuel pressure yet but can hear pump cycle when key is switched on.
View 8 RepliesFord Ranger / B-Series :: 1992 - Replaced Solenoid Now No Start?
I have to fix the truck. Battery is pretty new, replaced solenoid next to battery this morning. Truck still won't start, just clicking away. Decided I needed to replace the starter, put the truck on jacks and went to the starter. At the starter solenoid there is a red cable attached, and a "loose" red wire, with a connector on the end. It would appear the connector just needs to be reconnected to the solenoid. But it won't "connect". Am I missing something? Should it not connect to the prong on the solenoid? Should I just replace the starter, and forget about the wire? I do have Chiltons for our truck, but it doesn't show a picture of the prong on the starter solenoid.
View 11 RepliesFord Ranger / B-Series :: 2002 - No Start When Shut Off
I have a 02 ranger..3.0 standard trans 4x4.... Started running crappy, cleared up and when shut off, now wont start... Good spark and good gas pressure... Seems to want to try, but just doesn't go. No codes or pending codes.
View 8 RepliesFord Ranger / B-Series :: 2000 Does Not Want To Start After Shut It Off - Backfiring
I'm having problems with my 2000 ranger 4x4 off road edition it has 262,000 miles when it runs for about a half an hour shut it off try to start it in 20 minutes or so doesn't want to start sounds like it's backfiring to the throttle body replace the crank positioning sensor replace the ignition coil still doing it.
View 3 RepliesFord Ranger / B-Series :: B3000 Shut Off At Red Light Now Won't Crank Over Or Start
My mazda b 3000 shut off while at a red light i t turned over initially 3-4 times now nothing. changed EGR, ECM, CRANKSHAFT AND CAM SHAFT SENSOR three weeks ago. brand new battery, took alternator in and it was bad so i replaced. theft light is blinking rapidly?
View 2 RepliesFord Ranger / B-Series :: 1996 - Truck Suddenly Shut Off And Wouldn't Start
I have a ford ranger 1996 4 cylinder. The truck was driving fine then all of the sudden it shut off and wouldn't start... I checked spark and that is fine also changed fuel pump and made no difference. We also sprayed lighter fluid and that did nothing. It sounds like it wants to start but wont.
View 10 RepliesFord Ranger / B-Series :: 1992 - A/C Compressor Did Not Have Any Clutches On It
My compressor on my 92 Ranger did not have any clutches on it. Where they went. I got a compressor off of a 94 at the pick and pull. It was charged and the compressor turned fine. Brought it home and tried to install it. My hoses in the back of mine(92) are different than the 94. I went back and got the hoses, condenser and evaporator off of the 94. Put it all together. The high pressure hose on the 94 has some sort of switch on the high pressure side. What is this switch for and how can I wire it in to the electrical system on the 92? I assume it is some sort of pressure switch that allows the system to flow. I'm getting 30 pounds on the low side and 150-200 ponds on the high side. Also, when I increase the RPM's, the compressor kicks on and off. It's not like it would or should normally but fast.
View 7 RepliesFord Ranger / B-Series :: 1992 - Very High Idle At About 3500 RPM
My 92 ranger, 2wd, 6 cyl, manual trans, is running at about 3500 rpm at idle. I was wondering what might be the cause, maybe something with the throttle or could the gauge be screwed up.
View 14 RepliesFord Ranger / B-Series :: 1992 - Passenger Side Floor Getting Wet
Ok I got the brake pull fixed (I think) on my 92 Ranger 4x2 4.0 extended cab. I still will have to change the driver's side brake hose for prevention and the driver's side caliper just so everything will be new. But it stops straight now with a new brake job, pass caliper and hose on. However, this other problem has been ongoing and it does it on my 1998 Ranger too. It's not the heater core.
I think the evaporator case is filling with water and dripping down under the carpet. So the drain tube must be stopped or the case must have a bunch of leaves stopping it up. But where is this tube you're suppose to check? I don't see a conventional drain tube I only see a blower motor vent tube that doesn't drain to the outside of the car anywhere. I know my 73 Charger has a rubber drain tube that comes out of the evaporator case and drains onto the ground. But where is this one on a Ranger or what else could it be? It's only the passenger side so it's got to be that.
Ford Ranger / B-Series :: 1992 - Wheel Cylinder Blowing Out?
'92 Ranger 2WD with 4 cyl and 9" brakes, right rear wheel cylinder keeps blowing out, replaced it twice. I've thought about maybe an obstruction in the left brake line creating too much pressure, or in the junction block on the rear axle. I believe only one line leads to there from the master cylinder, so what else could it be? Only other thing I can think of is that the right brake has a mechanical problem which is causing the forward shoe to move too far away from the cylinder, leaving no 'stop' so the piston just slides right out of the cylinder. But I can't figure that. Original adjuster star wheel was chewed up so I swapped in another, doubt it's that.
View 14 RepliesFord Ranger / B-Series :: 1992 - EEC Relay 30 Amp Fuse Keeps Blowing?
I recently got a ranger from my buddy and it keeps blowing the EEC fuse in the engine compartment. We have replaced the EEC relay and the EEC power relay. As soon as you turn the key it is blowing the fuse.
View 1 RepliesFord Ranger / B-Series :: 1992 - Code 212 With CEL - No Power On Acceleration?
I have 92 ranger with 3.0 v6 in it.
It flashes out code 212 ive replaced the ICM and checked the spout connector for corrosion but it still flashes out 212 and has a rough idle no power on acceleration condition.
also when the idle starts acting up the check engine light stays real dim and if you rev it it will get brighter
Ford Ranger / B-Series :: 1992 - No Heat / Power Steering / AC?
1992 Ranger 4x2 with 2.3L stick shift no AC no power steering. Recently the temp gauge began fluttering in the cold range from far left to just below the normal range. The defrost and heater blows only cold air. I had a professional shop radiator flush done. No change. I changed the engine thermostat out for a new one but no change. The upper radiator hose feels hot, so I assume the thermostat is working.
Questions: Where is the temp gauge sensor located on the engine? Is there another sensor or shutoff before the heater that might not be working? Where do I take things apart to check if the heater blend door is working?
Ford Ranger / B-Series :: 1992 - Starts And Stalls / Won't Run More Than 3 Seconds
The truck started acting up while driving. It would shut off (no miss or anything), but would start again. Now it is sitting in the driveway and wont run more than 3 seconds. The fuel pump has been changed and did not work. The fuel pump relay is new and did not work. I read that the fuel pump goes to another circuit after start up. Could it be running to start and then shutting off? Inertia switch is not tripped. Where to look next. 1992 Ranger 6 cylinder ....
View 10 RepliesFord Ranger / B-Series :: 1992 - Front Brakes Pulling To Right
All I did was take wheel off to tap a stud and I saw the inboard pad shim came off. So I removed the shim and reinstalled everything and the wheel is severely pulling to the right. Yesterday I took the caliper off but did not take off hose, cleaned slide pins and lubricated with anti seize. Still pulling to right bad. Don't hear any squealing or grinding. But pass side wheel is definitely hotter than drivers side. One mechanic said he thinks it would be a bad hose before replacing caliper. What could it be?
View 8 RepliesFord Ranger / B-Series :: 1992 - Both Power Door Locks Won't Working?
So I've got this 1992 Ranger extended cab with power door locks and neither side is working. It has power windows too and they work fine. I checked the 30amp fuse under the hood for the power door locks and it's good and checked it with a test light and it's good. What's most likely the cause that both sides don't work? Is there a way to troubleshoot with a test light to trace down the problem as a bad switch or actuator?
View 10 RepliesFord Ranger / B-Series :: 1992 - Fuel Pump Does Not Work When It Is Cold Outside
I have inherited a 1992 Ford Ranger 4.0 with an unusual problem. When the temp drops outside the truck will not crank. The relay is coming on for a sec or 2 to bring the system up to pressure but the pump never turns on. This happens every time the outside temp drops below 60. I can wait until later in the day or until a warm day, hit the key and drive it till it runs out of gas. A week later (and another cold front) and it is sitting dead in the front yard. I have traced the grounds, checked the power thru the relay (and replaced the relay too), but it still does this. What I want to know is am I the only one to ever run into this and if not then what is causing it. Pump shows no sings of trouble on a 70 degree day, even runs the proper pressure and volumes. I am stumped at this point and I am ready to try replacing the pump (though the one in it looks brand new). comments?
View 11 Replies