Ford Ranger / B-Series :: 1988 XLT V6 Won't Start Just Crank
I have tried about everything i know about cars on this truck!! It ran great when I got it until a head gasket got blown so I tore into it and replaced them both torqued heads to specs. Made sure valves wasn't to tight. Distributor is in correct spot timing is correct had ignition module tested good!!! Coil tested good replaced both fuel pumps and put new tank and sending unit in the truck b/c it needed it new fuel filter replaced return line firing order is correct 1 4 2 5 3 6 it is getting fire it will crank and crank sometimes act like it is going to start then not also I can get it to run for about 3 sec on 3 or 2 cylinders it seems to have plenty of compression as well!! only thing really I can think of that could be wrong is computer? Also one last detail tried pull starting it as well still wouldn't go.... V6 2.9L...
View 9 RepliesFord Ranger / B-Series :: 1988 XLT - Oil Light Comes On / Lifters Start Clanking
My 1988 XLT 4x4 2.9L truck can't make up it's mind. Oil light comes on when ever it wants. I replaced it with a new one to make sure it wasn't bad. My lifters start clanking then they'll stop making noise when ever . Oil light goes out.Runs great. I let it Idle and once warm oil light pops on again. Rev it up light goes out then comes back on at higher rpm. Let Idle lifters clank again...and so on. seems erratic. Weak oil pump???? slop plugging pick up screen??? I'm running 20w50 oil is has 188,000. It ran today for 1/2 hour no oil light no noise then Here we go again..clanking valves ,oil light on...
View 4 RepliesFord Ranger / B-Series :: 1988 V6 Won't Start After Fuel Pump Replacement
I have a 1988 Ranger 2.9 V6 that sits most of the time. The fuel pump quit working so I removed the bed and replaced the pump in the tank and the inline filter near the engine. I did not replace the inline high pressure pump because it still made a humming sound so I assumed it is working. Now when I turn the switch on I hear both pumps working but the truck will not start. It seems like it wants to fire or fires for just a second but just wont completely start. Is the system supposed to be primed and if so how?. I suspect a fuel problem but I dont know how to check pressure or check to see if fuel is getting to the engine. What to do next?
View 6 RepliesFord Ranger / B-Series :: 2001 - Won't Start - No Spark
I have a no start no spark situation i am having trouble diagnosing
Truck started and then died it has fuel pressure but no spark I know that there is a theft light that is flashing (slowly) when the key is off. Could this bee the problem?
Ford Ranger / B-Series :: 1997 - No Spark / Start When Wet Or Humid Outside
997 2.3 TruckSo this has been an issue for a long time, actually one of the issues I had when I got the truck 3 years ago. After it rains or is extremely humid, my truck does not want to start. Sometimes it will after cranking and cranking and cranking for a while (stopping to cool the starter of course) and other times it won't start.
This time around, it won't start. I cranked it for a little bit and had my dad check for spark while cranking. No spark at all. What should I start looking at? Coils, crank sensor and wires are all newer. As mentioned before, EEC has been replaced. Could it just be bad luck and I got a crap crank sensor? All fuses and grounds are good.
No codes, either except for the occasional misfire code that I get for some reason after pushing in the clutch to decelerate from a higher RPM. It'll fall and start to misfire, but clear up when taking back off.
Ford Ranger / B-Series :: 1992 - Turns But Will Not Start / No Spark
My Ranger was running great when suddenly on the highway it just died. I towed it to local nationally known brake/ muffler shop where a good friend is the manager. He narrowed it down (guessed in my opinion) to no spark and no fuel. He thinks it could be the crank sensor, the fuel pump or the ignition module. Is there any way to pinpoint the problem without replacing parts? It will sometimes start and run for about 2 seconds before shutting off. It will not repeat this unless it sits for a day or two. I am not sure if there are different 2.3 engines available but mine is fuel injection and has two sets of spark plugs and wires.
View 9 RepliesFord Ranger / B-Series :: 1984 Has Spark / Cranks But Won't Start
working on a 84 ranger it did run fine for 3 wks then while driving there was a thump and it stopped and wouldn't start. Now working on it has spark cranks but won't start. while trying to start when I let off the key it tries to catch but only at that time not when the key is turn to start normal. we poured fuel into the carb and it still didn't start. Leaning toward compression maybe?
View 4 RepliesFord Ranger / B-Series :: Rough Idle At Start Up - Spark Plug 4 Keeps Going Bad
I'm getting tired of the same problem about every 6 months. Plug #4 keeps going bad. Its been doing this for years. It starts with rough idle when first starting up that clears up quickly then eventually it leads to a misfire when accelerating. Every time this happens I replace plug #4 and its good to go. Just recently (roughly 6 months ago) did a full tune up and all new injectors. About a week or 2 ago it started its rough idle at start up and just the other day it started misfiring again. What would keep causing this??
View 14 RepliesFord Ranger / B-Series :: 1994 4X4 Would Not Start / No Spark And No Fuel Pressure
Sons 94 ranger 4.0 4x4 Auto 185k got him to work yesterday but would not start to bring him home. No spark, checked with timing light, and no fuel pressure. Searched and read alot of tips from Pawpaw so I tried a few things with no luck. Swapped the relays around, inspected coil pack and plugs. CEL was not on and goes out while cranking. I have a OBD scan tool but this truck must be too old or I need finding plug. Crank sensor maybe?
View 7 RepliesFord Ranger / B-Series :: 1988 - Headlights Won't Turn On At All?
I have a 1988 ford ranger and my headlights won't turn on all my fuses are fine but no headlights! All the other lights work fine blinkers, parking, brake ,and tail lights! What do I need to look for????
View 14 RepliesFord Ranger / B-Series :: 1988 - Overheats While Idling?
My 88 2.9 ranger keeps heating up badly while idling. Was waiting in the drive-thru at Wendy's and it was taking them longer than usual, the temp guage started climbing closer and closer to 'H'.. I revved it up a bit to a fast idle (1500-2000rpm) and it did not work much... figured the gauge was being screwy. But when i finally got my food and started moving the truck was pinging..it really was hot..
But as soon as I got her moving at a steady 40mph, engine cooled back down to normal temp as if nothing ever happened..i put an extra wide two row aluminum radiator from a 4.0 explorer in it, fan clutch is not very old, no coolant leaks that i can see.. can't figure out why it heats up so much so fast at idle. Not enough air or coolant flow?
Ford Ranger / B-Series :: 1988 - Won't Idle - Starts Right Away Then Die?
88 ranger. 2.9L manual. Just bought this truck. It ran great when I bought it. After a day or 2 it would idle rough. Almost die but it wouldn't. No check engine light. It seemed to do this intermittently. Some times I'd start it and it be fine. Other times I'd start it and I'd expect it to die at each stop light.
Now for the last couple days it dies on every start up. It won't idle. It'll start right away and then die. I can keep it going by keeping the engine rev'd but the check engine light is one. If I keep it running and start driving down the road it'll drive with the check engine light on for about 5 minutes. Then the light goes out and it runs like normal, even at idle, until I shut it off. Then it's the same story at next start whether it's right after I shut it off or hours later.
It doesn't seem to matter whether the engine is hot or cold. When the check engine light is out, it runs great the rest of the time whether at speed or at idle. To me it sounds like a sensor is on it way out. I figure if it was vacuum, it happen at every idle, and if it was fuel it happen all the time or at least every idle. Tried to get a code at parts store but the reader wouldn't work. It couldn't tell it was plugged in the the truck for some reason.
Ford Ranger / B-Series :: 1988 - How To Tightened The Valve
It's an 88 2.9 and sounds like a little diesel! The fellow I purchased it from said the valves need tightened, I thought perhaps a timing chain, but figured valves would be an easier place to start. Yet, I'm not sure where to begin? Or how tight the valves need to be, are there torque specks?
View 2 RepliesFord Ranger / B-Series :: 1988 - Turn Signals Not Working
I have an 88 ranger with the 2.9l. The headlights work and the markers do to. The brights don't though. and also none of the turn signals work, the brake lights work though but i don't think the reverse do, I can't see them. Do the turn signals and brights share a fuse on there own? How to diagnose it or what it may be?
View 9 RepliesFord Ranger / B-Series :: 1988 - Missing / Stumbling Especially At About 55 MPH While In Overdrive
I've got a 1988 2wd Ranger with a 2.9l v6. I just recently got it running. It has been setting for awhile. I replaced fuel tank, both pumps, fuel filter, Plugs, Wires, Cap, Rotor, TPS. It ran great for about 100 miles. Then yesterday on my way to work about 4 miles down the road it started to miss/stumble especially at about 55mph while in overdrive. When I got home I pulled the codes and I got KOEO 22 Map sensor signal out of voltage(engine off), 53 TPS signal voltage to high, 95 Thermactor Air System Problem, or Fuel Pump Monitor signal, indicates circuit problem.
KOER I got 21 ECT sensor signal voltage out of range or loss of signal during normal operation or Crank Sensor problem, doesn't have a crank sensor I believe. But I did change the ECT sensor and it still stumbles and seems like it misses. Noticed it is sluggish getting up to speed kinda surges and bogs. Im at a loss it isn't showing any more codes. Checked all plug wire connections and made sure everything was making connection. The only other thing I can think of is that the ignition module on back of distributor is going bad. Not advancing the time correctly.
Ford Ranger / B-Series :: 1988 2WD Dies When Clutch Is Released
My Grandpa has an 88 Ranger 2wd with the 2.9l V6 and a 5 speed, I believe, M5od. I was driving down the highway when I heard a noise. I tried throwing the tranny in neutral but when I pressed the clutch pedal in, I had no pedal whatsoever. Engine took awhile to restart. It'd turn over a little almost as if a rod was bent or something of the sorts. Eventually the engine started and would stay running as long as the clutch was pressed in (disengaged).
The engine dies no matter what range the transmission is in,neutral included unless the clutch pedal is depressed. It Will die when the clutch is released in any gear with no forward movement that is noticeable. I can spin the tail shaft with the driveshaft installed and all gears in neutral but the input does not spin at all. Input shaft wont spin at all, period. I originally thought the slave cylinder was KIA but now I am very confused on what the problem could be? Is there a bearing the input shaft rides on that may of seized?
I pulled the tranny last night and took the top cover off. Yes, I made sure it was in neutral when I removed the cover. I can manually shift the collar to all gears by hand, 5th and reverse included. I'm stuck between a rock and a hard place here and where to go from here. I have bought a new clutch assembly and slave cylinder. This truck was bought by my Grandpa brand new in 1988. It has 98,000 miles and everything is original. I did forget to mention that there was very little oil in the trans when I drained it and it appeared to be gear oil vs ATF.
Ford Ranger / B-Series :: 1988 4x4 - Stalling / Cutting Out Sputtering
When I'm driving it starts to cutout (but it never dies) and it won't stop cutting out until I floor it and then it's fine for a little bit and it starts doing it again.
View 1 RepliesFord Ranger / B-Series :: 1988 - Power Loss Like Coil Getting Bad
Bought my third 88 ranger today, drove it 55 of 60 miles home and it died. It lost power and acted like the coil was going bad. This one is a 2.9 5 speed 4x4. The a/c compressor is gone; but the 365 a/c works okay, or did.
My daughter was following me in her car; by the time we got back with my F150 and a chain, it started and ran until it was a half maile from home then lost power and died again.
Drug it home, put a new coil on and it started and revved up fine. Went to move it a couple of hours later and it will crank with the starter, but not fire.
I am getting 12 volts to the primary side of the coil, is there any way to check the TFI module without taking it off the distributor? (they are so accessable).
Or is there something else that I need to check? I really don't want to just throw money at it, I like to know for sure what is wrong before I buy parts.
Ford Ranger / B-Series :: 1988 - Rusted Rear Brake Lines
I am going to fail State safety inspection due to a problem with my brakes. Months ago when I was trying to get it through emissions testing the mechanics looked under the truck to see where the brakes were leaking. All they told me was the rear lines are rusted through and need replacing.
From my reading I believe the lines are 3/16" line and I think they go around the back of the fuel tank and up the frame rail. Correct?
My questions are, what length line do I need (I am not a hard-line expert, but I will try). I want to order some ss line so it won't rust through again. Is the system made of small sections threaded together? Or is it one long section? And what else would I need/want to replace along the way?