Ford F-150 (2004-2008) :: Misfiring - Rough Idle - Got Codes P0340 / P0344 / P0345 And P0349?
I recently purchased a Ford pickup. I bought a 2004 F-150 with the 5.4L 3V engine. I have only driven it for about 300 miles so far and am having problems. The engine has 200,000 miles on it. I have read several posts on here about the cam phasers which I believe that I may have some issues with. The engine will run good when cold, on the road, etc. The engine does have a slight ticking after it warms up (cam phasers?). When I come to a stop after the engine is operating temperature, the engine will start to miss and shudder and all 4 above codes come active and are also pending (8 codes in total).
All 4 codes are logged at the same time. I have replaced both cam position sensors, both sensor ends and terminals for cam position sensors, checked wiring around rear of engine (does not appear to be rubbed through), all plugs were replaced, and all COP boots are good. Is there anything that can cause these codes that may not be the actual cam position sensors, ie. VTC, COPs, cam phasers? What pins the cam position sensors come to on the ECU (so I can ohm the entire wire harness)?
Also, if the engine is missing with the codes active and I rev the engine up it will come back to idle and run great. The engine never dies out, just runs horribly. I have also unplugged each sensor with the engine running which has no effect on the way it runs.
Lexus RX 2004-09 :: Misfiring And Check Engine Light Codes
The car was misfiring and the check engine light codes were all sensor coils were bad. Lexus told me that it was coil6 bad and they fixed it. I should have had no problems, I got a whole 2 miles and I misfired and engine light back on. I drove for a while and light went off and then misfired again. Before I bring it back in I was looking for some insight. I can't understand how it wasn't fixed right the first time but I don't want to go back and get a few thousand bill either. Could fixing one coil cause another to go bad.
View 1 RepliesFord F-150 (2004-2008) :: 5.4 3v - Rough Idle / Stalling And Misfiring
I recently bought a 05 f150 with 5.4 3v and 195k miles needing some work. Ran great, just had a code for timing over retarded. Originally it had a cracked timing cover, so i took it off to replace and found broken guides and bad tensioners on timing. I installed new guides, chains, and tensioners, and cleaned phasers, and put back together only to find it ran terrible and had a phaser rattle. I then went in and installed phaser locks, which took care rattle but not the running issues. I can not figure it out.
ISSUES: My issues almost mirror what is said in this thread here, but this issue was never solved. [URL] ....
My issue is when started cold it starts right up, idles ok, runs ok, although a bit sluggish. Once its warm it stalls at idle, shudders when giving throttle in overdrive, and if you kick it down it will continually backfire, and slowly accelerate... it kicks down but acts like its only getting 1/8 throttle, just kind of hangs at the same rpm and slowly climbs in rpm. Sometimes it wont backfire as much, and sometimes the check engine light flashes. After it stalls at idle and you start it back up it sounds like it shudders/backfires for a split second then starts.
It is throwing many engine codes, but most are from the phaser locks. Throws code for timing over advanced on each bank (phaser locks lock them fully advanced), cam timing codes for each bank, and then a code that doesn't have to do with the timing, P2106. I am going to run some live diagnostics on it today and report back but I am fully at a loss.
Ford F-150 (2004-2008) :: Truck Started To Develop A Miss - Multiple Codes
Apparently yesterday (no known reason) my sons truck started to develop a miss (so it feels like to me).
2005 f150 5.4 auto 215000km 4x4 stx. No specific cylinder codes. All general codes.
P1000
P1464
P1550
P1703
P1780
None of which I can see causing the miss. No check engine lite, no other codes. Not sure what to look at next. I am starting to disconnect the coil packs one at a time and see if I can pin down the cylinder.
Ford Ranger / B-Series :: 2002 - Rough Idle Codes / Cylinder 2 And 3 Misfiring
I have an 02 ranger xlt 3.0, it started having a rough idle, codes say cylinder #2&3 misfiring, changed plugs, wires, coil pack, didn't work, still same code, checked injectors on right side, all 3 had ohm reading of 15.8-16.5, the injectors were clicking like they are supposed to, sprayed carb cleaner around the intake ports, didn't change the idle at all,what else can I check or do? with out tearing the engine apart, unless of course I have to, the truck has been very good to me, it's got 205,000 miles on it, I need it to last at least another year...
View 4 RepliesFord F-150 (2004-2008) :: Miss At Idle - Got Codes P0351 / 356?
I bought a 04 FX-4 a couple months ago with 102k on it. Brought it back to selling dealer, they replaced #1/#6 coils, its ran great till this past week. Again it has stumbled a couple times this week. It only seems to have the miss at idle (comes and goes) take off from light, within 50 feet its running like a champ again. I cleared the codes (disconnect battery)and now it seems my idle is not steady, it fluctuates. Is the idle a product of the codes?
View 2 RepliesFord F-150 (2004-2008) :: 2006 - Rough Idle With Many Codes
I just received a 06 F150xl with a 5.4 triton and idles rough with the following codes! p0357 p0012 p0340 p0344 p0351 p0352 p0356 p0358 p0357 p0102 p0113 p0353 p0354 p0355 It's amazing the truck even runs and with no light on but it will accelerate. someone mentioned to clear the codes and drive it 50miles or so and read them again.
View 9 RepliesFord F-150 (2004-2008) :: No Codes / Low Idle / High STFT And Load?
For the techs in here, I have a data logger (AutoTap) and the symptoms are low idle and sometimes it runs rough idling and driving. It had me thinking the fuel pump was going out. That is not the case. I did get into part swapping mode so I have new plugs and coils and new VCTs all in the last 24 hours. The engine has 85K miles on it (rebuilt ford long block), truck had 150K. I'm not sure what parts were replaced when the longblock was replaced but I'm guessing the 02's are original.
Data that looks odd to me in the Autotap real time data logging is this:
- STFT Bank 2, goes from 10-15% and climbs till its over 300% and then the truck goes into Open Loop due to an error (per the Autotap) but it never says what error and the CEL never lights. Idle goes up when its in open loop and then after a minute or two it will drop back into closed loop.
- Fuel pressure never drops below 37
- Idle will drop to 250rpm
- Engine load at idle is 25%?! With AC on and idling (at 550rpm) engine load is 42%? Seems high no?
Nothing else other than the STFT Bank 2 and the high engine load seems out of miss. No misfires, codes, etc. What else should I look at?
Other background/patient history:
- Alternator #3 was installed 2 weeks, It replaced alternator #2 that went in 4 months ago to replace the original alternator (144K miles). Both died and caused low voltage/battery dying symptoms and verified by volt meter.
- FPDM was replaced proactively 8 months ago just because I don't want it to break down when I'm towing my race car.
- I have not tried cleaning MAF, EGR?, IAC, nor have I replaced O2s. The only thing that leads me to believe MAF might need cleaning is the load?
Ford F-150 (2004-2008) :: 2005 - Check Engine Light Came On And Pulled Codes P2160 And P0506
I have an 05 F-150 Lariat 5.4 and it has been going haywire today. While driving if I hit a hard bump the power will cut off (radio, a/c) and even sometimes the truck. Check engine light came on and I pulled codes P2160 & P0506. Also, when it completely cuts off and I start it back up it says "engine in failsafe mode".
View 1 RepliesFord F-150 (2004-2008) :: Battery Drains When Truck Idle
I have a 2008 F150 that the battery drains after sitting 4 days or longer. This has happened about a dozen times since I bought the truck and the dealer could never figure out why. Warranty is up now and it is STILL happening! I had corporate office insult me by telling me everything "checks out" and it is just like a cell phone. If you don't periodically charge it up, the battery dies. I asked her where I was supposed to plug my truck in at night and there was silence on the other end. I am 62 and have never had a car or truck do this from just sitting. The dealer insists everything checks out.
View 14 RepliesFord F-150 (2004-2008) :: Rough Idle / Truck Wants To Stall
Let me describe this perplexing issue. I have a speratic rough idle problem. When it happens it's almost like the truck wants to stall. Once going the truck is fine. There has never been any acceleration issues, but for a short time the truck would kind of lunge off idle. It hasn't done that for quite some time. I've replaced the fuel filter. There are no vacuum leaks that I know of. I've tried higher octane fuel. I've tried injector cleaner for a month. What should the fuel pressure be and what is the test port located? Is the fuel pump in the tank? If so, whats that big log looking thing behind the gas tank that the fuel lines run to? Also, there are no MIL codes...
View 14 RepliesFord F-150 (2004-2008) :: Truck Quit Running At Idle
This morning I drove down to unlock my gate and got out of the truck while it was idling. When I got to the gate the truck just stopped running it did not sputter or anything it was like a light switch and just shut off. I got back in the truck and tried to start it but nothing happened starter did not engage at all or even try to run. I put a new battery in it knowing that is not the problem but it will just not start or even turn over.
View 1 RepliesFord F-150 (2004-2008) :: Vacuum Leak Causing Erratic Idle - Codes PO171 / 174?
I tugged on the little hose on the back pass. side of the engine,(5.4),...
and I could hear the vacuum leak that is apparently causing the erratic idle, and PO171 & PO174 to come up.
I know this hose is hooked to the Charge motion Control Valve on the back of the manifold,..I can't imagine what it does, as it terminates with some kind of plug or check valve??? Haynes say's to remove the entire manifold to get to the CMCV.
I can see it with a mirror,. I am thinking maybe long needle nose from Harbor freight,...bend the tip short,..maybe be able to change it out?????
Ford F-150 (2004-2008) :: Rough Idle / P0012 - Misfire Codes Associated With Bank 1 And Cylinder 3
5.4 3v. my last few weeks have not made me a fan. Here are the details:
I bought a 2008 F150 XL 5.4 3v with a cam phaser knock. Have done other timing jobs in past with no trouble so I was not too afraid to tackle this one. famous last words...opened the motor (shout out to the passenger side valve cover and its designer here) and found semi damaged roller follower on driver side. Worn cam lobe on the corresponding lobe and a loose chain on passenger side. proceeded to :
Change all timing components: phasers, chains, tensioners crank sprocket, all applicable bolts and BOTH cams as well as all lash adjusters and roller followers. most looked fine in fact all really did with a bit of wear on a few roller followers but only one bad one. engine didn't look to bad pretty clean.
Double and triple checked my timing chains and it was spot on. dark link on spot on crank, two dark links on the L and R dead on. put it back together. oh yes, changed all plugs with motorcraft ones, didn't even break one. did not change vct solenoids because I falsely assumed I could change the later easily if needed. they looked ok. screens intact etc... silly me for not realizing how kind Ford was in 2007 and later to necessitate removal of valve cover. I was reading a previous one on the how tos and assumed later models would be the same since it was the same sensor...
Cranked truck ran great. I mean perfect. sounded perfect. ran like a scalded cat. till it got to hot idle then it started doing its thing. rattle shake till you revved it. ran fine just wouldn't hot idle fine especially in reverse or under slight load. replaced driver side vct since ford only had one and I started on the easy side ordered the other one waiting for it. seemed to improve dramatically meanwhile I am driving this truck to test it. I drove it to work 50 miles each way and it ran great.
After a few trips it popped the P0420 light, seemed to run ok, cleared it watched it wouldn't come back. O2 sensor did seem to imply a bad cat on bank 1 since it seemed sensor two was mimicking sensor one and not staying stead like the other bank. still ran fine,
So I decided to check back pressure on the cat. I pulled sensor one out of bank one (really a joyously tight squeeze in there) hooked up my gauge and got 0 back pressure. revved it and all nothing. hooked sensor back up pulled truck out of shop and it commenced to running like crap. I mean bad. running worse than before I got it. Popping P0012 code continuously, and tons of misfire codes associated with bank 1 ..cyl 3 etc.. I tried swapping coils, pulled coils and checked spark with a tester and firing away looks like tons of good spark.
Now the weird part is : looks like bank one is dead. I can unhook any coil pack and/or injector and it runs the same and sounds like it is missing. if I unhook one off of bank 2 it almost dies or does. so bank 2 seems to be running fine. it will start and run but sounds like it missing sets flashing check engine light and backfires and stalls like crazy. I even second guessed my pressure gauge and unhooked exhaust manifold from pipe and it sounds even prettier when it backfires out of there but no change. I pulled cam sensors and cleaned it again and even tried swapping them since they looked identical but no change so I put them back.
Now I can only surmise that I am out of time somehow? or I have a gremlin perhaps? I like working on cars (usually) but this one is getting old. how do I verify what is wrong. if it is timing related how do I verify that now definitively once my marks moved I really cant figure out how to tell if it is in time? Since it has all new parts and they all ran beautifully till now. could it possibly be the vct solenoid doing all this? I plan on changing it when it comes in but surely it cant cause this many problems.. I unhooked it no change, and it does it at a cold idle and any rpm. really runs worse at idle but bad at any rpm.
Ford F-150 (2004-2008) :: 2005 FX4 Truck Extremely Rough Idle
A week and a half ago I went out to my truck to go somewhere and I got about 2 blocks away and the truck started running really rough and had a big lack of power, so I turned around and scanned it with my code reader and the codes I got were p2271, p2196, p0303, p0012, p2197, and p2272. since then I've changed all the spark plugs, boots, swapped all the coils and injectors from a great running truck, fuel filter, and the bank 1 upstream O2 sensor.
the other thing that came to mind that could of caused the problem is that a few days before the problem started. I jump started a co-workers car and he hooked the cables up backwards on his car. Could this be the cause of the problems I'm having.
The truck is an 05 F150 FX4 5.4 with 180,000 miles on it.
Ford F-150 (2004-2008) :: Idle Will Drop Down When Stopped And Truck Sounds Like It Is Going To Die
My friend just bought a 2008 F150 5.4 110k, it ran great all day during all of the test drives, after he gets it home it has started acting up. Most of the time it runs great, but sometimes when you stop the truck the idle will drop down and the truck sounds like it is going to die but so far it hasn't actually died, it starts knocking really badly and runs very rough. If you let it keep running like that it sets P0340. If you rev the truck up it cleans up and sounds fine again and it will even drop back down to a clean idle most of the time. I swapped the cam sensors because it was easy and just to see and it didn't make a difference, I was hoping after switching the sensors the code would switch to the other head but it didn't.
View 14 RepliesFord F-150 (2004-2008) :: Truck Is A Bit Rough At Idle - B1360 Code - No CEL
So I bought a 2006 F150 stx reg cab with the 4.6l motor with 90k miles on it a few weeks ago. It was in really good condition and I couldn't pass the deal up. All in all, I love this truck. However at idle the truck is a bit rough. No check engine light, but a bit rough non the less. So I hooked up my obd2 torque app and I see I have anywhere between 6 and 60 total counted misfires, but none detected by individual cylinder. So I ran a scan and have a B1360 code without the CEL on. So I changed the plugs and coil packs and cleaned the k&n filer (non cold air filter, just a replacement k&n) and I still have all the symptoms and the b136p code. So I Google the b1360 code and there's very little on it. Basically says open circuit ignition.
View 1 RepliesPrius (2004-09) :: 2008 - Check Engine Light Came On With Codes
I have a 2008 Prius that I purchased used last year. It has just shy of 139,000 miles on it. Recently the check engine light came on, and I dropped by AutoZone to have them pull the codes. They are as follows:
C1241
P1121
P3193
I haven't been able to find a full explanation of the codes online, so I need to know what they mean, how much it would cost to fix, and how urgent the repair is. I will be going on a 5 1/2 hour road trip next week, so I want to make sure I'm not going to break my car (or myself!) by doing so with the engine light on.
Ford F-150 (2004-2008) :: 2006 - Missing And Rough Idle - Codes P0340 / P0344 / P0345 And P0349?
I recently purchased my first Ford pickup. I bought a 2006 F-150 with the 5.4L 3V engine. I have only driven it for about 300 miles so far and am having problems. The engine has 146,000 miles on it. I have read several posts on here about the cam phasers which I believe that I may have some issues with. The engine will run well when cold, on the road, etc. The engine does have a slight ticking after it warms up (cam phasers?). When I come to a stop after the engine is operating temperature, the engine will start to miss and shudder and all 4 above codes come active and are also pending (8 codes in total).
All 4 codes are logged at the same time. I have replaced both cam position sensors, both sensor ends and terminals for cam position sensors, checked wiring around the rear of engine (does not appear to be rubbed through), all plugs were replaced, and all COP boots are good. Is there anything that can cause these codes that may not be the actual cam position sensors, ie. VTC, COPs, cam phasers? What pins the cam position sensors come on the ECU (so I can ohm the entire wire harness)?
Also, if the engine is missing with the codes active and I rev the engine up it will come back to idle and run great. The engine never dies out, just runs horribly. I have also unplugged each sensor with the engine running which has no effect on the way it runs.