Ford F-150 (2004-2008) :: 2006 - Misfire On Cylinder 1 / Code P0301
I have a 2006 F150 with a cylinder #1 misfire only code p0301. I have done new spark plugs, new coil packs, and new fuel injector on cylinder #1 with no luck. What to do next?
View 5 RepliesPrius (2004-09) :: Number 1 Cylinder Misfire - Error Code P0301
So I dropped my prius off to get looked at for error code p0301 number 1 cylinder missfire. They ruled out Spark plugs, coils and fuel injector. What else is ther? Also could it be the battery or even gas?
View 12 RepliesFord F-150 - 1997-2003 :: CEL Code P0301 / Misfire With Cylinder 1
My 97 F150 through a CEL Tuesday night P0301 so I picked up a new plug because it's cheap and simple, but that didn't do anything. Spark plug wires are about 3 months old, I also swapped injectors between 1 and 2, and misfire stayed with cylinder 1. It also gained a tap when the misfire started but only above idle, but it doesn't sound like a rod knock.
I also noticed if you unplug injector 1at idle it taps/knocks 3 or 4 times, however if you unplug any of the others it doesn't do that. I checked and I definitely have good spark from the plug. I plan on picking up a new compression tester tomorrow since mine never was returned. If you take the oil fill cap off it doesn't have any blow by at idle, however if you rev it you get a quick cloud out of it.
I thought about picking up a kit to check the injector pulse.
Ford - F150 :: 2003 - Code P0301 / Misfire On Cylinder 1 Keeps On Coming
I am at about my wits end with this P0301 (Misfire On Cylinder #1) code on my 2003 Ford F150 4.6L. I've replaced the coil pack on that cylinder, all the spark plugs, and replaced the fuel injector on that cylinder. We keep clearing the code and it keeps on coming back.
The weird thing is that it only misfires after the truck has set for a few hours and then it only misfires when I first put it in gear. Once I am out of the driveway and on the road it's fine for most of the day unless I let it sit for several hours and then it might misfire again.
We noticed that the connector to the fuel injector is wobbly and doesn't snap tight to the fuel injector (before and after it was replaced) due to the clips on the side not working well. We zip tied it together this afternoon to make it fit tightly to the fuel injector to see if that works.
What could be causing this? Other than that misfire the engine sounds great and the trucks runs very well.
Ford F-150 - 1997-2003 :: 1998 - Cylinder 1 Misfire / Code P0301
I have a 98 F150 4.2L with code P0301 Cylinder 1 Misfire.
This is what I have done so far. New plugs, coil pack, plug wires, TPS, EGR, EGR Vacuum control regualier, DMCP, canister, all of these parts are new and was bought from the ford place. Have taken the egr value, and egr value bracket off to see if carbon blockage was present, but it was clean. It was clean in the motor also. Have blown air through the metal tube that connects to the egr value and it come out the tail pipe very good, so no blockage their. Have cleaned throtle body and injectors. Have tested fuel injector with tester and it works correctly. Motor holder pressure. Have correct fuel pressure.
Do not have any vacuum leaks, it holds vacuum correctly. Crankshaft sensor is fine. Went throw 4 cans of break parts cleaner, spraying on intake while motor was running, motor did not idle up or change. I have done all this and it still shows code P0301, and it still skips. Here's the catch, if you unplug the vaccum off the egr the misfire goes away, or unplug the EGR vacuum control regulator it goes away, or if you unplug the DMCP sensor it goes away, it does not matter witch one you unplug, the misfire goes away.
I have had several different test done the the truck, but all the test only show that one code P0301, they do not show any other codes, or problem's with my truck.
Avalon 2005-12 :: Various Misfire - Common Code P0301 Which Is Cylinder 1
'07 Avalon with 169k miles. I replaced all 3 back coils and 6 plugs back in December when I had various misfires, but the most common code was P0301 which is cylinder 1.
Car ran great until last week when I made a hard left and accelerated. CEL started flashing, read code and it's P0301. Every time I accelerate half throttle or more I can set the code off, but then shutting down car and restarting it drives fine, until I go half throttle. Car runs better when cold, and worse when I turn left and accelerate.
As long as I don't mash the gas I can drive for a half hour or so without the strumbling/hesitation. Surely the new coil hasn't failed so soon, I hate to pull the wipers, plenum,etc. and buy another coil just on a chance that might solve the issue. Car is only throwing a P0301 this time, no other codes like before. I've read a clogged cat or sticky exhaust valve could cause a cyl misfire.
Corolla / Matrix 2009-13 :: 1.8L - Code P0301 And P0303 Misfire On Cylinder 1 And 3
2009 corolla 1.8l 155,000 miles. Replaced iridium spark plugs at 100,000
I got a CEL few weeks ago, P0301 Toyota - Cylinder 1 Misfire Detected
Car has been running bad for about 2 weeks now, excise noise on the highway, especially up hills.
Yesterday, I took a look, replaced the spark plug in cylinder 1, same results. Checked the coils using one of those flashing tools, all 4 flashed quickly, with no breaks in flashing. put it all back together, cleared the code, went home.
Took it out for a drive today, and it started running way worse. Checked the CEL, and now I have both P0301 and P0303 Misfire on cylinder 1 and 3. Barely made it home, ran VERY VERY bad.
Got home, and made a video of it. It just kept dying. Check it out here. [URL] .....
Also, when it does run, it almost sounds like I can hear excess air, its hard to hear in video, but doesn't sound right. Maybe air leak? How do I check?
Passat (B5) :: 1999 1.8 Turbo Automatic AEB Engine - Cylinder 1 Misfire Code P0301
I have a 99 Volkswagen Passat 1.8 Turbo Automatic AEB engine. I recently did a rebuild on it and ever since I keep getting this code P0301 that says "cylinder 1 misfire". The engine is also running rich and the spark plug in cylinder 1 keeps getting gummed up. I've changed the coil and the spark plugs and the injectors and it works temporarily but then the problem keeps reoccurring.
View 7 RepliesFord F-150 (2004-2008) :: 2007 - Cylinder 3 Misfire Code
I know there is a tun of info on the spark plug problem on the f-150. Here is the problem I have and I don't know where else to look.
Cylinder #3 misfires
1. swapped coil with #2 cylinder and still throws #3 misfire code.
2. Changed the plug on #3 and still the same code #3 misfire.
Where to look next?
Ford F-150 (2004-2008) :: Cylinder 8 Misfire Code Randomly
Having a misfire problem I can't track down. First issue was random cylinder 8 misfire code. Checked everything, nothing obvious. Cleared code, problem stopped and engine ran fine. Then came back, cylinder 8 misfire. Swapped coil with #5 but problem did not return. Since I assumed it would come back, I went ahead and bought Accell supercoils and new Motorcraft plugs and replaced them all (120k miles, no broken plugs ). Truck ran great on the test drive! Then it sits overnight and bam, cylinder 5 misfire as soon as I start it next morning. Then after messing with it I get cylinder 5 bad coil (code 355 I think). Put one of the Ford factory coils back back on #5, no change and still misfiring. New plug, new coil on all cylinders... Why did it move from #8 to #5? If it was an in injector, seems it would still be #8 since I did not mess with those.
View 10 RepliesFord F-150 (2004-2008) :: Code PO306 Which Is Misfire On Cylinder 6
I have a 2004 f150 with the 5.4 and was wondering what would cause a spark plug to do this. Its on cylinder 6 and i have pulled the codes off of the truck before and one was PO306 which is misfire and can't remember other one but it was saying system was too rich. I have only has this spark plug in maybe 500 miles. but was getting a misfire code before that. Do you think it could be a coil or the injector?
View 3 RepliesFord F-150 (2004-2008) :: Code P0308 Read Out Misfire On Cylinder 8
Started as I was warming up the truck,a slight vibration/shudder. First thing that came to mind was F150. Torqued words of wisdom that it might come back, I had a p0301 before. Had no CEL, so decided to drive it to see if it got worse. Turned onto the main road and on came the CEL. Pulled into my FORD dealer, told him about my problem. Code P0308 misfire on #8cylinder was the read out, COP was done and the plug. 40 min of labor. She's even quieter than when #1 got changed.
View 3 RepliesFord F-150 (2004-2008) :: E250 - Code PO306 Misfire On Cylinder 6
I have a 08 E250 4.6 getting code po306 misfire #6.. What should I check or change first and where is # 6 looking from the front of truck looking at the seats the driver's seat on my right # 1 is where and #6 is where oh 57,342 miles...
View 4 RepliesFord F-150 (2004-2008) :: Loss Of Power - Code P0306 / Misfire On Cylinder 6
Having 3 new codes coming up. P0306-misfire on cylinder 6, p0158, p2272. Use my truck as a daily driver for work. Driving along before 80km/h is not to bad but can still feel a little loss of power. If i step down on gas the truck has no power and sounds like maybe cat converter is plugged. If truck is pushed to limit she will make it to her 4000 rpm and will change her gears. So i'm just glad its not tranny.
View 3 RepliesPrius (2004-09) :: Code P0301 - Cylinder 1 Misfiring During Warm-up
I have a 2009 Prius that I purchased 6 months ago and have been really happy with it until the last couple of months. As the weather is getting colder appears I have a misfiring problem on start-up
I have had this problem now for a little while and have been trying to get it understood before paying $$ at the dealer for "maybe" solutions.
It started as the weather got colder. Intermittently the check engine light would come on. Then after a few days would go off.
I have considered water in the line: fuel injection cleaner/antifreeze
I have considered bad gas in the tank: problem persists several fuel tanks later
I have recently purchased a trouble code reader/diagnostic that plugs into my laptop. Trouble code is p0301. Cylinder 1 misfire.
I have taken it in to the shop.They tried:
>>moving the ignitor coil from cylinder 1 to cylinder 4,
>>and also tried moving the spark plug from cylinder 1 to cylinder 2.
>>performed compression test. Ok
The dealer suggests replacing the injector line for $1400+.( They did this with warm engine. They have not diagnosed cold engine yet. That is new, read more,...) I still have 5K kilometers left on the power-train warranty. If it is power-train I would like it resolved before warranty expires.
Now. Some new info as of yesterday:
Up till now I was not using the diagnostic monitor real time. but that started yesterday,... Last night when I got home from work while the engine was still warm I connected the diagnostic monitor and went for a drive. Every few minutes I would pull over and refresh the cylinder misfiring data. I had hardly any misfires across all the cylinders at all. Maybe 1 or 2, here or there over the span of a 10 minute warm engine ride. Up and down hilly terrain. Nothing that came close to triggering the p0301 trouble code. I parked the car outside and let it rest overnight.
Ford F-150 (2004-2008) :: Cylinder 7 Misfire / Cylinder 6 Has Oil On Plug
06 F150 fx4 has cly 7 miss fire cly 6 has oil on plug .Check engine light comes on only if you step into the gas, The oil was low. If you drive normal the check engine light does not come on, but you can fill the miss when in gear. Change the plugs an coil add oil still no change.
View 4 RepliesFord - Taurus :: 2001 - 3.0 Engine Misfire Consistently / Code P0301
I had a consistent misfire on this car and finally got a P0301 trouble code. I installed new Autolite AP 104 plugs and wires. Now, when I start the engine. it runs perfectly. But when I put it in gear, it misfires. After a minute or so, the misfire clears and the engine runs perfectly. I have not received another trouble code. One thing I did notice is that the plugs I took out (Motorcraft AWSF 32P) had a much larger gap than the .044 the associate at AutoZone set the new plugs to.
View 7 RepliesFord F-150 (2004-2008) :: Misfire On Cylinder 4
2004 F150 XLT 5.4l (3v)... Problem started with misfire on No.4 and then I went through the tedious job of changing every plug (all 8 broke) and coils in an attempt to resolve the problem. After the changes I had misfire on no.1 and no.2, so I changed the injector on no.2 and coil on no.1 again + had broken pigtail wires on No.4 and No.1. Now I remain with a P0301 misfire on No.1. The problem won't go away, its fine idling, but misses bad when driving. The Snapon scanner reads fine for all injectors and compression reads ok also. The mechanics are baffled and what else could it be? (rail? computer? intake gasket?)
View 4 RepliesAccent MC (2006-11) :: 2008 - Code For Cylinder 1 Misfire / CEL Flashing
I have a 2008 Hyundai Accent that is giving me one heck of a headache. I keep getting a code for number 1 cylinder misfire. When you start it up it runs fine for a while then the CEL will flash and it will start running rough. As soon as I shut it off and restart it, it runs fine. I even experimented with it this morning on the way to work. It started running rough doing 60, I put it in neutral, turned the car off and then right back on, put it back in gear. It ran fine the rest of the way to work. I have swapped coil packs, fuel injectors, spark plugs, and have even hang tested another ECM. Still number 1 cylinder misfire.
View 8 Replies