Prius (2004-09) :: Number 1 Cylinder Misfire - Error Code P0301
So I dropped my prius off to get looked at for error code p0301 number 1 cylinder missfire. They ruled out Spark plugs, coils and fuel injector. What else is ther? Also could it be the battery or even gas?
View 12 RepliesFord F-150 (2004-2008) :: Code P0301 - Misfire Cylinder 1
This happened xmas shopping with the wife. Started misfiring on the highway,took the 1st exit to find a garage as I am 20kms from home. The vibrations were worse at stop, but made it to a garage. They gave me the p0301 misfire cylinder 1, said they don't touch 5.4 plugs, told me to go to ford 2kms down the road. NICE. 4 in the pm, FORD dealer worse case scenario. Nope gave me a loaner told me come back at 930am. Truck was just waiting for an injector when I arrived. Plug & coil were good injector was shot,changed the fuel filter & oil change.
View 6 RepliesFord F-150 (2004-2008) :: 2006 - Misfire On Cylinder 1 / Code P0301
I have a 2006 F150 with a cylinder #1 misfire only code p0301. I have done new spark plugs, new coil packs, and new fuel injector on cylinder #1 with no luck. What to do next?
View 5 RepliesAvalon 2005-12 :: Various Misfire - Common Code P0301 Which Is Cylinder 1
'07 Avalon with 169k miles. I replaced all 3 back coils and 6 plugs back in December when I had various misfires, but the most common code was P0301 which is cylinder 1.
Car ran great until last week when I made a hard left and accelerated. CEL started flashing, read code and it's P0301. Every time I accelerate half throttle or more I can set the code off, but then shutting down car and restarting it drives fine, until I go half throttle. Car runs better when cold, and worse when I turn left and accelerate.
As long as I don't mash the gas I can drive for a half hour or so without the strumbling/hesitation. Surely the new coil hasn't failed so soon, I hate to pull the wipers, plenum,etc. and buy another coil just on a chance that might solve the issue. Car is only throwing a P0301 this time, no other codes like before. I've read a clogged cat or sticky exhaust valve could cause a cyl misfire.
Ford F-150 - 1997-2003 :: CEL Code P0301 / Misfire With Cylinder 1
My 97 F150 through a CEL Tuesday night P0301 so I picked up a new plug because it's cheap and simple, but that didn't do anything. Spark plug wires are about 3 months old, I also swapped injectors between 1 and 2, and misfire stayed with cylinder 1. It also gained a tap when the misfire started but only above idle, but it doesn't sound like a rod knock.
I also noticed if you unplug injector 1at idle it taps/knocks 3 or 4 times, however if you unplug any of the others it doesn't do that. I checked and I definitely have good spark from the plug. I plan on picking up a new compression tester tomorrow since mine never was returned. If you take the oil fill cap off it doesn't have any blow by at idle, however if you rev it you get a quick cloud out of it.
I thought about picking up a kit to check the injector pulse.
Prius (2004-09) :: Engine Light, Error Code P0301 Came On
So I changed my spark plugs, due to an error code saying p0301 which means cylinder one misfiring. I reset the engine light disconnecting the negative battery terminal. Once it reset it ran rough for a few miles. I put about 50 miles on it and it seems better.
View 2 RepliesCorolla / Matrix 2009-13 :: 1.8L - Code P0301 And P0303 Misfire On Cylinder 1 And 3
2009 corolla 1.8l 155,000 miles. Replaced iridium spark plugs at 100,000
I got a CEL few weeks ago, P0301 Toyota - Cylinder 1 Misfire Detected
Car has been running bad for about 2 weeks now, excise noise on the highway, especially up hills.
Yesterday, I took a look, replaced the spark plug in cylinder 1, same results. Checked the coils using one of those flashing tools, all 4 flashed quickly, with no breaks in flashing. put it all back together, cleared the code, went home.
Took it out for a drive today, and it started running way worse. Checked the CEL, and now I have both P0301 and P0303 Misfire on cylinder 1 and 3. Barely made it home, ran VERY VERY bad.
Got home, and made a video of it. It just kept dying. Check it out here. [URL] .....
Also, when it does run, it almost sounds like I can hear excess air, its hard to hear in video, but doesn't sound right. Maybe air leak? How do I check?
Ford - F150 :: 2003 - Code P0301 / Misfire On Cylinder 1 Keeps On Coming
I am at about my wits end with this P0301 (Misfire On Cylinder #1) code on my 2003 Ford F150 4.6L. I've replaced the coil pack on that cylinder, all the spark plugs, and replaced the fuel injector on that cylinder. We keep clearing the code and it keeps on coming back.
The weird thing is that it only misfires after the truck has set for a few hours and then it only misfires when I first put it in gear. Once I am out of the driveway and on the road it's fine for most of the day unless I let it sit for several hours and then it might misfire again.
We noticed that the connector to the fuel injector is wobbly and doesn't snap tight to the fuel injector (before and after it was replaced) due to the clips on the side not working well. We zip tied it together this afternoon to make it fit tightly to the fuel injector to see if that works.
What could be causing this? Other than that misfire the engine sounds great and the trucks runs very well.
Ford F-150 - 1997-2003 :: 1998 - Cylinder 1 Misfire / Code P0301
I have a 98 F150 4.2L with code P0301 Cylinder 1 Misfire.
This is what I have done so far. New plugs, coil pack, plug wires, TPS, EGR, EGR Vacuum control regualier, DMCP, canister, all of these parts are new and was bought from the ford place. Have taken the egr value, and egr value bracket off to see if carbon blockage was present, but it was clean. It was clean in the motor also. Have blown air through the metal tube that connects to the egr value and it come out the tail pipe very good, so no blockage their. Have cleaned throtle body and injectors. Have tested fuel injector with tester and it works correctly. Motor holder pressure. Have correct fuel pressure.
Do not have any vacuum leaks, it holds vacuum correctly. Crankshaft sensor is fine. Went throw 4 cans of break parts cleaner, spraying on intake while motor was running, motor did not idle up or change. I have done all this and it still shows code P0301, and it still skips. Here's the catch, if you unplug the vaccum off the egr the misfire goes away, or unplug the EGR vacuum control regulator it goes away, or if you unplug the DMCP sensor it goes away, it does not matter witch one you unplug, the misfire goes away.
I have had several different test done the the truck, but all the test only show that one code P0301, they do not show any other codes, or problem's with my truck.
Passat (B5) :: 1999 1.8 Turbo Automatic AEB Engine - Cylinder 1 Misfire Code P0301
I have a 99 Volkswagen Passat 1.8 Turbo Automatic AEB engine. I recently did a rebuild on it and ever since I keep getting this code P0301 that says "cylinder 1 misfire". The engine is also running rich and the spark plug in cylinder 1 keeps getting gummed up. I've changed the coil and the spark plugs and the injectors and it works temporarily but then the problem keeps reoccurring.
View 7 RepliesPrius (2004-09) :: Gen II Car Started Randomly Shaking Both When Accelerating And At Idle / Code P0301
I bought a second hand 2005 prius (gen II) at 125k km. Soon after I got the car I got p0402 and p0505. After clearing the errors, I got back only p0420.
About a month later, my car started randomly shaking both when accelerating and at idle. This happened 2 or 3 times in the span of 2 weeks. The CEL and traction control light started flashing. I stopped the car and started again like absolutely nothing happened 10 seconds ago. (This time I got only p0301.)
Yesterday, the situation with the shaking was horrible and I got p0301. Naturally, average fuel usage went up a lot. Even at idle on the parking lot, I turn on the aircon so the engine would start - the feeling is like the car is going to collapse any second.
I have recently used a new gas station, so I thought possibly bad fuel. However, if it was bad fuel, i should have gotten all misfire mistakes, right (p0300~p0304)?
So if I am getting only p0301, the problem should be either the spark plug, injection coil, fuel injector etc. for cylinder 1. My car is currently at the mechanic's place, so all of the above are being checked as we speak.
However, what I am worried about is that this shaking / lights flashing drama is happening at random. If it was any of the above, shouldn't is just happen all the time? When I went to the mechanic yesterday, I barely made it there. He was busy, I waited for 20 minutes, then he wanted me to drive the car for a bit to see the problem. This time the car was working like a brand new car. Absolutely nothing happened. He probably thought I was crazy.
So yeah, he will closely inspect spark plugs, injection coils, fuel injectors etc. If all of them are fine, where should we look next? Head gasket leak perhaps?
Prius (2004-09) :: Shaking When ICE Is Running - Misfiring On Cylinder 1
My Prius started shaking pretty bad when the ICE is running. This morning I got the codes read and it came as Cylinder #1 misfire. I figured the coil pack is going bad (as is known to happen) so I swapped #1 and #2. The misfiring actually got better for about 30 minutes, but it finally happened and the CEL flashed again.
So I took it to get the code read but he said the only code is still #1 misfire. Perhaps the ignition coil is OK then? I bought a new spark plug, maybe the plug has gone bad. The plugs only have 45k miles on them. I'll swap it out and see what happens. What I should do to diagnose the issue? It seems to be slowly getting better...this afternoon it was much better than this morning but still shaking sporadically.
Corolla :: 1999 - Fixing Misfiring Code P0303 On Cylinder 3?
The issue with 99 Corolla CE with 147,000 miles....
I have a misfiring P0303 Code - Cylinder #3 Misfire. Here is what has been done in an effort to remedy the misfire. A major tune up, new spark plugs, new fuel injectors, new spark plug wiring, new coil packs, The car runs ok once warmed up but in the morning the engine vibrates until warm and also shivers a little while the car is stopped at a stop light. I have dropped it off at the mechanics a couple of times now to no avail. Once the code is reset it will not display the CEL for a couple of days but the symptoms still remains. The CEL comes back on within 2-3 days with the same code. Really frustrating! Well, at least this time CEL in not flashing like before it comes on and stays on.
Chrysler - Pacifica :: 2006 - CEL On / Code P0305 Cylinder 5 Misfiring
So my Pacifica, after a long road trip around a year and a half ago, had it's check engine light come on. The meter read P0305, which is cylinder 5 misfire. When I got home, my local trusted mechanic replaced the coil and wire. Since then, the same misfire has occurred at least 4 times, and 3 of which he replaced the same parts (free warranty swap of the parts). The last time, he was determined that it wasn't simply the parts going bad. I concur. It has now lasted roughly a month and the light is back on with the same code. The spans have been as little as a week between leaving the shop and the light coming back on. I personally don't feel the car riding rougher than normal, but my wife does. I don't smell gas, have odd colored exhaust, or any other issue. The only other thing, which idk if it's related, is a clicking noise from the engine, which quickens with revving, perhaps the risers. What else could it be? I read that Chrysler's go to is a valve spring retainer lock and a MAP sensor that accompanies it.
View 19 RepliesCorolla / Matrix 2009-13 :: OBD2 Error / P0304 Code / Cylinder 4 Misfiring
Went on a trip Sunday, and i saw my engine light come on after i put gas in the car. I pulled over, re-checked the gas cap, and it was fine. Car felt fine.
When i got home, i used my OBD2 scanner, and got the error P0304 Code - Cylinder #4 Misfire. I cleared the error and drove the car some more, no issues.
Yesterday, my wife took the car and she said it was hesitating and sputtering, but the light hasn't come back. I have an appointment at the dealer tomorrow, the car has under 80,000k, so the warranty should kick in.
Ford - Taurus :: Check Engine Light Keep Flashing - Code PO302 Cylinder 2 Misfiring
I have a 1996 ford taurus lx v6 3.0 dohm..my check engine light flashing. then it stop flashing..i did replace spark plug,wires,coil pack..when it start to flash i put it gear the car start to shake and sputter.i really don't know why its doing that the car has about 150000 miles on it..i do get a code p0302 Cylinder #2 Misfire..the new plugs and wires and coil pack is about 2 weeks old..
View 11 RepliesPassat (B5) :: 2001 - Misfiring - Got Codes P0300 / P0301 / P0302 / P0303?
i have a 01 passat with a v6 in it on 4 motion and im having an issue with soem mis-firing
i pulled the codes. P0300 P0301 P0302 and P0303 which are all saying that there are missfires in cylander 1,2 and 3 and random miss fires.
im also getting a P0340 which is cam sensor A or the right hand bank. problem is i just replaced the cam sensor and when the motor got warm, the code came back. I was told by the previous owner that the car needed a Coolant Temp Sensor....can this be the cause of my mis-fire issue? hear me out.... it only happens when the car is warm so im thinking that the car is warm but the ecu thinks its cold cause its not getting a good signal from the CTS. thus its either advancing the timing as if the motor is cold and cuasing a miss fire or something along those lines. any thoughts?
Ford - Explorer :: 2004 - Misfiring On Cylinder 3 And 6
Changed the spark plugs now I have misfire in cylinders 3 and 6. Do I change the spark plug wires or the coil pack?
View 5 RepliesGolf IV / Jetta IV :: 2004 - CEL Came On - Cylinder 2 Misfiring
CEL came on and the report says #2 cylinder misfiring. Changed plugs, wires and coil. Last step was to change the #2 fuel injector. I changed the 2nd injector from the left but I'm still getting the same message. I was wondering if maybe they aren't numbered that way. It's a 2004 Jetta with Car engine: 2.0L L4 SOHC 8V. Did I change the wrong injector?
View 1 Replies