Saab - 9-5 :: 2003 - Coolant Standing In One Cylinder - Blown Head Gasket?
A local mechanic tells me I have a blown head gasket on my 2003 Saab 9-5. He also said there's coolant standing in one cylinder. If this is due to stretched head bolts, might I remedy the problem by replacing the head bolts and torqueing to specifications?
View 4 RepliesFord F-150 - 1997-2003 :: Blown Head Or Intake Gasket?
My 97 f150 5.4 started missing on 5,6 it had antifreeze on top of the spark plugs but i cant figure out where its coming from my truck has been loosing coolant and it seems like the system is holding pressure because every time i take the cap off the radiator overfill i can hear it hissing then i see the antifreeze level plummet there's no visible leaks that i have seen when the truck is running an missing it steams out the exhaust but when its no missing it doesn't seem to be there's no milky oil or anything the thermostat doesn't seem to be leaking either the truck has over heated a couple times due to the antifreeze disappearing or the temp wont move at all then it shoots all the way to hot and cools down within seconds to normal i just put a new thermostat in. Also it sometimes misses on 4 and my exhaust smells like straight gas i put 4 gallons in it got 29 miles out of it .
View 10 RepliesFord F-150 - 1997-2003 :: Engine Has Blown Head Gasket
I just bought a used 5.4 for my 99' F150 4X4. My current engine has a blown head gasket. Anyway, I was able to hear the engine run before I bought it, and was able to check it out some. (oil, anti-freeze) I was told that this engine was bought from a salvage yard with 50K, and 50K more put on it before I bought it.
I was also told that the intake manifold is newer, from Autozone, and it has newer Accell coils. My question for you all, is ..... What do YOU think I should do otherwise before I install this engine. Oil pump? water pump? seals? ...
Ford F-150 - 1997-2003 :: Head Gasket Blown - Camshaft Retainer
I have my 4.6L engine on a stand in the garage. I think I have a blown head gasket. I am ready to remove the heads.
My Haynes book says: "Caution:Use the required camshaft retaining fixtures to lock the camshafts and leave the tools in place."
A google search shows nothing. Why, what does it do?
Ford F-150 - 1997-2003 :: Water In Oil And Exhaust - Blown Head Gasket
I just purchased a 2003 F150 Supercrew 4.6 that had been wrecked, but somewhat repaired. I knew the owner said it had a blown head gasket. It has water in the oil (small amount asi it is lightly milky) and water starts dripping from the exhaust after it has run for a few minutes. I did not run it long, but throttled it up to warm the engine. It started dripping soot filled water from the exhaust connections. I bought it to put a 4bt in it anyway, but want to sell the motor with the ability to tell the buyer the skinny on it. I drove it on the trailer and off with no apparent loss of power noticeable.
View 2 RepliesFord F-150 - 1997-2003 :: Ticking Noise Coming From Driver Side Cylinder Head
My wife is talking to someone about purchasing a 1998 4.6 4x4 EB Expedition. The owner says the only issue is a tick coming from the driver's side head. He claims the shop told him it was "just a cam stator". Now, say what you will, but I've dabbled just enough with mod motors (2v and 3v, 4.6's and 5.4's) to feel like I'd rather stick to old pushrods. I've never heard of a "cam stator" on a 2v 4.6. I also realize that stator is a word that gets tossed around a bit by people who don't fully understand what it is.
Now, this is a relatively high mileage engine (something like 220k I think) so I know it could be a whole slew of things from cracked/leaking exhaust mani, lifters, timing chain, etc. But, in all my searching, "2v 4.6 cam stator" keeps leading me to people troubleshooting pushrod distributors, 3v VVT troubleshooting, and alternator related posts. Is this such a thing, what this shop may have been trying to refer to? He claims it's done it for about 5 years now, and runs perfectly fine. I'm leaning towards lifter, but the truck is 3 hours away so I haven't got to check it out yet....
Ford F-150 - 1997-2003 :: Truck Running Rough / Intake Manifold Gasket Blown
I have been having some issues with my 97 ford f150 4.6 liter, started out running rough, then hydrolocked with no serious damage, blown intake manifold gasket, fixed that, alternator over charging do to bad voltage regulator, fixed that. and airbag code 52, still working on that, as well as failure to connect when trying to do diagnostic scan. now I am wondering if the engine diagnostic is still even working. still running good just a very slight vibration when warms up. I am not getting any code. or my check engine light is not showing any codes. What I want to do is force a code. What would be the safest way to force a code or force engine light to give a code?
View 6 RepliesFord - Taurus :: 1997 - Blown Head Gasket - Overheating - Antifreeze Came Out Of Reservoir - Leak?
Radiator replaced 2 yrs. ago - required major rust cleanout; reservoir replaced shortly thereafter. Recently engine always hot, antifreeze disappearing, reservoir always looks rusty, nothing much coming out underneath, mechanic pressure tested and couldn't find a leak, told to watch for antifreeze in oil, none apparent. Now suddenly car ran hot, antifreeze came out of reservoir, cap replaced, still couldn't find leak. Today said head gasket blown. Repair head gasket, but can't guarantee wouldn't still have radiator problems. Suggested could try Blue Devil head gasket repair but may not work.
Is it worth :
(a) trying the Blue Devil;
(b) repairing the head gasket?
Or will I still have major repair needs with radiator etc.? I really can't afford even a cheap replacement car.
Ford F-150 - 1997-2003 :: Head Gasket On Passenger Side Number 3 Is Leaking
I have a 97 with a 4.6 Triton motor I need to replace the head gasket on the passenger side number 3 is leaking nothing else is wrong with motor so I have it torn down to timing chain cover and ready to remove. do i have to take the drivers side valve cover completely off to take timing chain cover off or can I take to first 2 studs out of the drivers side front valve cover and side the timing cover off. I just want to replace the passenger side head gasket and get rid of truck.
View 6 RepliesCamry :: 2003 - Oil Leak From Driver Side Head Gasket
I own a 2003 Toyota Camry with 195,000 miles. We have owned the car for about 6 years. It is now leaking oil from the drivers side of the head gasket. The oil has been leaking down onto the exhaust and smoking, and it has been getting worse and worse. This is a second car and is not used much, only once a month for short trips. Is there any temporary fix for this that can maybe get me through a year? Also, I have heard mixed opinions on how hard replacing the head gasket is, does the engine really need to be removed?
View 9 RepliesFord F-150 - 1997-2003 :: Leaking Antifreeze Externally At The Front Of Passenger Side Head Gasket?
Working on a 2000 F150 with the 5.4 and as near as I can determine its leaking antifreeze externally at the front of the passenger side head gasket. Seems a little odd. The coolant is a nasty dirty orange color. With the truck running on the hoist it was dripping very steady off of the very front exhaust manifold bolt.
View 3 RepliesImpala - Chevrolet :: 2003 - Stalled After It Ran Out Of Oil - Head Gasket Blown?
My 2003 Chevy Impala stalled after driving it for about a mile. The 'low engine oil' came on. I noticed white smoke coming out from under the hood. I pulled the dipstick and it was out of oil.
I poured 2 quarts of oil and attempted to start the car. The car started after I pressed the gas pedal but shut off when I took my foot off the gas. I tried several times. It started butshut off when lifting the foot of the pedal.
I'm hoping it's not the head gasket.
Civic - Honda :: 1997 - Cylinder Head And Gasket Replacement
I have a 1997 Honda Civic that I was given by an elderly neighbor's daughter after the elderly lady went to the grocery and ended up 100 miles away when she could not figure out how to get home. The car was smogged at the beginning of the year but when I got it ran very rough and the temp went nearly to overheating on the drive home when I was stuck in stop and go traffic.I found the radiator fluid level low and an oily residue inside the radiator water bottle. I took it to a mechanic to check it out and was told it had a blown head gasket and maybe worse.
I am thinking of buying a rebuilt cylinder head and replacing it myself but I am not sure how to diagnose if any other damage could have been caused to the engine. It's hard to know but I am guessing that the engine was damaged during the 100 mile road trip due to low coolant level. It turns out short term memory loss was the diagnosis for my elderly neighbor. I filled the coolant level and ran the engine for a bit and the temp stayed normal but the rough running remains. The oil dip stick shows no signs of coolant in the oil and the coolant looks bright green when I looked in the radiator after topping it up with some water.
Any way to detect if I could be facing bigger issues like failed bearings? I am OK to do the head replacement but an engine replacement starts to get into the realm of what it would cost to get another car of the same age.
Ford F-150 - 1997-2003 :: Fuse For Driver Side Power Seat Blown
I don't know what to try next. I have a short somewhere, just don't know how to track it down. I checked the fuse for the drivers seat and it was blown. I stuck a new one in and the thing blew as soon as I stuck it in. I disconnected the seat motors, plugged in a fuse and it blew again as soon as I stuck it in. How to track this down?
I don't see any worn or shorted wires under the seat. I checked under the passenger side kick panel per another post I found, but that looks fine. I don't know where to look or what to test.
Ford Super Duty (1999-2016) :: 2003 5.4 F250 Head Gasket / Misfire Code On Cylinder 4?
After replacing most of the underside of my Super Duty, Complete front end, backing plates, brakes, rotors and shocks, I have a misfire code on cylinder #4. I replaced the plugs, cleaned the MAS and filter and rotated the coil to cylinder #1. Still have a misfire on #4 and noticed the coolant slightly low and some condensation on the oil cap. Could this be the intake gasket? My mechanic is away for 2 weeks and I think the price at the dealer will kill me. I have 63K on the truck, don't tow and plow mostly family members. It's getting a little rusty but is still in good shape.
View 13 RepliesFord - Explorer :: 2006 - Head Gasket Blown?
i have a 06 explorer with the 4.0 V6. 4x4 XLT with 106xxx miles. i just bought this thing back in January. of corse, i didn't get an ext warranty. well the past couple months its been loosing power, its got a stumble and seems sluggish. its losing water. no water in oil, no oil in water, don't smell coolant in the exhaust. yesterday i went out and looked and found at front of head on pass side at front cyl, there was coolant from head gasket down the block and also in the valley of the block. i started the engine and once warm, everything was dry. shut it off after about 20 minutes and still nothing wet. this afternoon the only wet spot was in the valley which was dry after running yesterday. is there anything else i can check before tearing it down? with the water in the valley, it looks like it could be coming from the thermo housing.
View 6 RepliesFord Ranger / B-Series :: Blown Head Gasket?
I have read all I could find on replacing a blown head gasket and and after absorbing everything that TigerDan posted on here, I dove in and began. After disassembling all the topside junk I finally got the intake manifold loose and got down to the head. I began undoing the head bolts and found two broken bolts. The head won't budge so I am calling in a cherrypicker. I don't know what kind of mess I'll find when the head comes off. I assume the head will be warped or the block may be damaged.
View 6 RepliesFord - F150 :: Intermittent Overheating - Blown Head Gasket
I have the same problem as the gentleman w/ the '97 4x4 4.6. Intermittent overheating. The water pump and t-stat have both been replaced, as well as the radiator. Some one told me a piece of gasket material from the heater core may be floating around and periodically clogging things. Could this happen? and what's the fix? Also, someone told the guy w/ the 4x4, that he could have blown head gasket, and to perform a sniffer test to find out.#1. What is a sniffer test? #2. If the head gasket is blown, wouldn't there be water in the oil?
View 4 RepliesFord 6.0L Power Stroke Diesel :: Possible Blown Head Gasket?
Truck is a 2006 F-350 6.0, ARP studs, Ford Head Gaskets, Bullet Proof Diesel Oil Cooler Kit and EGR with an SCT tuner on tow mode.
Towing approx 15,000 pounds noticed truck started to lose power and misfire. Pulled over and noticed engine oil all over the driver side on engine, looks like it sprayed to top of engine as well. Oil on valve cover, FICM, exhaust manifold. I looked under the truck and saw that oil is all over bottom of the truck, differential covered in oil as well. Looks like blue smoke coming from tailpipe and smells of oil burning. Cannot tell where oil originated from.
I removed the EGR Valve, to see if there was moisture on the valve and when I looked into the intake manifold there is engine oil pooled in the bottom of the intake manifold and on the EGR Valve.
This is not dirty water from soot, it is oil. Truck is misfiring, with no codes being thrown. I noticed a small amount of white residue around the radiator cap however I had just filled up the reservoir, week prior. I unfortunately do not have gauges in the truck and rely on the factory gauges; coolant temps did not rise or move at all when this happened. I am not sure if I blew a head gasket, and really confused on how engine oil got into the intake manifold. I ran the engine with the air filter removed and can see blue smoke coming out of the CCV and oil in residue in front of the turbo inlet.