Ford F-150 - 1997-2003 :: Truck Starts And Then Immediately Stalls / Idles About 3 - 4k RPMs
If I don't keep in the throttle immediately after start up it will stall a lot of the time. It doesn't do this every time or if it sits for a while but if I drive it and then stop off at a store or something and then go to start it back up it gives me this problem. I notice it idles about 3-4k RPM's when I stop at a light or something too.
View 14 RepliesFord Ranger / B-Series :: Truck Idles With Very High RPMs When Driving And Shifting Gears
1999 ranger, 2.55 speed. truck idles with very high rpm's when driving and shifting gears. have changed the AIC, mass air sensor. Throttle position sensor and still does it. the AIC has been changed 5-6 times in 6-8 months as parts store kept telling me it was that. What can i look at, check, etc...
View 6 RepliesFord F-150 (2004-2008) :: Truck Idles High And Rough In Any Setting From Park To OD / Stopped Or Moving
I am trying to solve a mystery on my mom's truck. It's an '06 4.2L F-150 STX with about 133k miles. It had a check engine light on until today- I cleaned the TB and changed air filter yesterday, and both were filthy. Code vanished later on while driving.
I want to check the PCV because the truck idles high and rough in any setting from park to OD, stopped or moving. Worse when stopped though. Entire coil pack has already been changed due to previous misfire problems. This feels similar to a misfire but without the acceleration hesitation. It has also had a recent oil change, and fuel/oil filter change as well.
There is only one hose connecting to the intake on this truck, and it appears to be a vapor line of some sort to the valve cover, but isn't a PCV cause it's just a hollow tube. There is nothing else coming out of the TB at all, except for the throttle control cable. I don't even seen any nipples or connections or holes where a PCV hose or valve should go. I thought it was on the passenger side, under the TB... but there is nothing here at all. I'm stumped.
I am beginning to think the truck just does not have one at all, which I know for a fact is impossible. I have traced every line on this motor from top to bottom, and I do not see it. Should have a heater on it I assume? What else can make the truck so rough? I don't buy it that "it's just that way". That is complete, lazy, BS. I have had/driven many trucks; 4x4s, supercrew, diesels, jeeps, dump trucks... I have NEVER had a truck run as badly and roughly as this one does. Heck, a twin-turbo 700HP diesel doesn't run this roughly.
Ford 7.3L Power Stroke (1999-2003) :: 2000 F350 Idles Fine But Runs Rough After Warms Up A Little
2000 F350. Starts great. Idles fine. After it warms up a little, it will run rough and lose power like it is only hitting on a few cylinders. It will eventually stall unless I push the clutch in and bring it back to idle and then it smooths back out. I figured it was starving for fuel but I can rev it with the clutch in with no issue. I ran it up to 2500 rpm and held it there with the clutch in and ran perfect.
I let the clutch out and start rolling....missing again. The check engine light does come on but my scanner says that there are no codes stored. If I idle it, it will smooth out, and the light goes off. All I have done so far was change the fuel filter which was almost plugged shut and the housing was full of rust looking debris which I cleaned out. BINGO! Nope. Same issue.
I am really at a loss as to where to start. I bought this with 120k on it and it now has 170k and I have not had to do anything other than routine maintenance.
Ford F-150 - 1997-2003 :: Idles Fine With Occasional Surge / Sputters In All Gears Like A Misfire
I have a 01 f-150, 4.6L, with 160k miles on it. Symptoms: It idles fine with an occasional surge. It sputters in all gears like a misfire (all plugs and COPS replaced 2 months ago). Sometimes it stalls out going down highway or as I turn in my driveway. It also seems like its slipping a little without the "hard jerking into gear". Occasionally the rpm meter will peg low and then return to normal.
The only code that I received was P1451. I changed the canister vent solenoid but the symptoms remain. I've checked voltage on the TPS (the variable voltage checked out but I didn't get the 5V ref. voltage). I've cleaned the MAF sensor. I've also changed the fuel filter. I've resistance checked the connector to the PCM and found several pins that are at ground. I'm not sure what to do next.
Ford F-150 - 1997-2003 :: Idles Fine But Sputters Out As Soon Put It In Gear After Hitting Large Water Puddle
I have a 2002 F150 super cab with the 5.4 liter v8. I hit a large water puddle on my way to work Tuesday. I was going faster than I probably should have been. After hitting the puddle the truck lost power. It idles fine but as soon as I put it in gear it sputters and has no power. Also, the O/D drive light is now flashing. What might be going on with it.
View 4 RepliesFord 7.3L Power Stroke (1999-2003) :: After Start Up RPMs Drop - Stalls Out Then Idles Rough?
2003 7.3 excursion.. The truck starts every time revs up and idles about 3 seconds then the rpms drop and it tries to stall out catches itself then revs backup and idles rough similar to if you have got air in the fuel lines from changing the fuel filter.. About 1 in five times the truck will stall out and it starts and immediately and idles rough but the rpms and everything runs at speed and rpms don't drop again! This is a reman engine/transmission recently installed.. The mechanic who installed it was unable to figure the problem out.
View 6 RepliesFord Ranger / B-Series :: 2003 Truck Idles A Little Rough - Code P1450
Where to start looking to resolve this code. It is not an intermittent code. It returns after about 3 to 4 key turns. Truck idles a little rough but runs fine. I have looked up the code and causes but wondering how to deal with this directly and fixed it. I'm wanting to sell my truck for something bigger and would like to solve the issue before hand. 2003 Ford Ranger Edge...
View 4 RepliesFord F-150 (2004-2008) :: 2007 - Starts Good Idles Fine Jumps And Shakes Over 800 RPMs
2007 5.4 . Starts good , idles all day. As soon as you try to rev it, it stumbles rattles etc. Shut it off, wait a second, restart then Idles fine. I watched live Data and it carries on when the VVT solenoids become active (above 800 rpm).There duty cycle goes to 60-70 percent while revving. I think it Is just one side of the engine. Could be VVT solenoids sticking on? yes ? No?
View 3 RepliesFord F-150 - 1997-2003 :: Idles Rough And Seems To Lack Power
I am working on a 97 4.6 with 146k for a friend. It idles rough and seems to lack power (then again a 4.6 lacks power )
Has New:
plugs
wires
coil packs
fuel filter
sea foam intake
sea foam fuel
I have checked:
proper egr function
vacuum leaks
cleaned IAC
steady 17-18 in vac
clean air filter
cats do not seem to be getting too hot.
no codes
KOEO test ok
KOER test ok
The plugs worked some. Dirty MAF, clogged cats??
Ford F-150 - 1997-2003 :: 2001 - Idles High For A Few Seconds When Putting In Reverse?
I got my first truck about a months ago 2001 ford f150 v8 5.4.. has 155,000 seems to run good.. but about 3 days ago i started to notice that when I am in my driveway ill start it let it idle for say a min or so... then when I go to put it in reverse it will idle up for a lil bit.. it didn't do that till about 3-4 days ago.. other them that everything is fine.. should i get the transmission fluid flushed??
View 7 RepliesFord - Escort :: 1999 - Rough Start / Couple Of Hiccups But Runs And Idles Fine
I have a 1999 Ford Escort SE wagon with 112k miles on it. Last week when leaving work my car started very rough. This was unusual so I killed and restarted the car about three times before letting it run it's course (~30 seconds), after which the car ran fine. About a week later on my way to work the car seemed to 'sputter' (for lack of a better word) when I pushed down on the petal looking for some power on two separate occasions. On each side of the sputters the car seemed to respond fine, but when it did sputter there was a severe lack of power. I got to and from work just fine, but while letting the car idle in the parking spot of my apartment for a minute before shutting off the engine the check engine light finally came on. The following morning the car again started rough (as if it were misfiring/running on 3 of 4 cylinders) and this time it took a good minute before smoothing out. However, after the car smoothed out I experienced no issues on the way to work, no sputtering, no loss of power, nothing. Doing some initial online research I feel that the problem may be one (or more) of the following:
-Fuel pump
-Vacuum lines
-O2 Sensor
-Spark plugs (they are original)
-Fuel Filter (it is actually past due for replacement)
I plan on getting this checked out ASAP, but that still may be 2ish weeks away with my schedule. Some similar reports say that I may be having a 'lean mixture' issue (not getting enough fuel), but I haven't had the time to check the code. My question is, how "safe" is it to continue driving my car with the current situation? Is it at a super high risk of failure/random stalling during rush hour? Will it cause any damage to the engine if there is a cylinder misfire upon start up? I was also wondering if the car would be reasonably reliable to drive on a ~400 mile road trip on an upcoming weekend, but I am making plans as if it is not.
Additional Details:-Tried charging the fuel lines (car to 'ON' then 'OFF' position 3-4 times), had no effect on the morning start-up-Commute to/from work is about 20 miles
Ford F-150 - 1997-2003 :: 2002 V8 - Misfiring / Exhaust Is Smelling Very Rich / Idles Rough And Stalls
2002 f150 4.6l v8... Truck is misfiring and the exhaust is smelling very rich, I have new coils and plugs, it also idles rough and stalls if i let it idle for more than a couple minutes. Could it be something with fuel delivery system?
View 1 RepliesPrius (2004-09) :: Starts Fine But Idles A Little Rough
Just recently my Prius Taxi with 340,000+Km has developed a little problem,it starts fine but after 20-30 seconds it begins to feel like it's not running properly on all four cylinders,if i go to the exhaust pipe it seems like it's spluttering slightly.
Yesterday I changed the plugs,checked air filter and all connections,everything fine, when I accelerate it feels hesitant but after the car gets up to temp it seems to go away,it only happens when i start it first thing or if it's been left for a few hours, it's never had the throttle body cleaned and I'm wondering if what I'm describing is a symptom of this?
Ford F-150 - 1997-2003 :: Truck Stumbles - RPMs Drop When In Gear
I have a 1997 forkd F150 with a 4.6L Romeo engine. I have recently rebuilt the engine and now since it is put back together I am having a issues that i cannot pin point. When the truck is running and in gear my RPM drop to around 500 or below and my oil pressure drops and comes back up when the rpm's come back up this an intermittent problem and I have replaced the IAC valve and every once in a while i get a P0401 code for the exhaust recirculation. I think I am loosing some kind of vacuum. It was not doing this when I tore into the truck. It seems to be running okay not hesitation.
View 2 RepliesF Series :: 1982 F150 Truck Starts And Idles Just Fine But Stalls At Stops
Today I acquired a 1982 F150 with a 302 engine, 4 brl. Edelbrock carb. The truck starts and idles just fine, but when I come to a stop, try to give it gas to go it dies. It starts right back up, and I have to rev it high a couple of times then put it in gear and it will finally go. When I got it home I let it idle a few minutes and tried playing with the air and fuel mix but don't know what I'm doing, really. It seems I can hear a hiss, and when I was reaching for the air/fuel screws I got a little shock on the hand from the distributor. We want to use this truck as a farm truck, and plan to get a manual for it, but what might I might check for the cause of it stalling.
View 1 RepliesLS / MKZ :: 2002 Lincoln Idles Rough On Cold Mornings But Runs Fine
The car idles rough on cold mornings but runs fine. It will stall while idling but starts back easily. I am getting a 1131 and a 1151 code with my scanner along with 0300 and lean bank 1 codes. I started having these problems after I had to remove the upper intake to replace coil packs. I was getting egr code and had an egr port completely block off but cleaned that out and no longer get the egr codes. Spraying carb cleaner around the engine I get a very slight bump in rpm around a couple of the intake ports could that be my problem or should I look deeper?
View 5 RepliesFord F-150 - 1997-2003 :: Rough Idle / Engine RPMs Go Up To 2k Before Dropping Down
1999 F250 LD with 5.4 w/ 225k miles... Was running perfect yesterday when I shut the engine off. Started back up about 20 minutes later and Idles was up and down and rough.( 400 - 900 rpms) Drove and ran fine except Idle. I know that those codes are for the o2 sensors but don't believe they're bad. I hear what sounds like a vacuum leak somewhere behind throttle body. Either IAC or EGR or it could be coming from the line that runs in beside the IAC valve to the air intake in front of the throttle body. Tried spraying water in those areas with no results. Could it be a bad EGR valve or a stuck IAC valve? I have also noticed that lately when I start the engine the engine rpms go up to 2k before dropping down. Would a bad IAC valve cause such rough idling along with the codes that I described?
View 7 RepliesMazda - Protege :: Very Rough Start / Idles Fine And Stalls As Soon As Touch The Pedal
1995 Mazda Protege1.5 LAuto153K miles.
My car was running fine, then one day it started sputtering while driving, mostly when I accelerated. It stalled and I could not get it started. This happened on a day when it was raining hard, but not sure that had anything to do with it. A few days later when I went to pick the car up it started right up, it had stopped raining and been dry for 2 days prior. But about a mile into the drive back home it stalled and I could not get it started.
Here is what I have tested so far.
- Put in new fuel filter.
- Tested the fuel pressure and pressure regulator
- Tested the injectors with a noid light.
- Tested that the spark plugs were producing a spark.
After I pulled the plugs and cleaned and dried them (they were wet with gas) the car started, but I think not because of anything really related to the plugs. What I've noticed is that when cranking the engine if I give it gas it will not start but if I keep off the throttle it will reluctantly start. But once it starts the idle is smooth and as it should be. Then if I give it any gas it immediately stalls. It seems to me given these symptoms that it is getting enough air to idle but not enough air to match the increased gas.
The only CEL code that I'm getting (which I had before this issue occurred) is the "closed throttle position switch" (I forget the number). If it was an MAF, or IAC, or EGR issue would I not get a code? What this could be and how to test it. Again my guess is its an air intake issue but not sure where.