Ford F-150 - 1997-2003 :: 2002 5.4L Engine Stalls Out Unless Keep Foot On Gas Pedal On Hot Days
As the title says, I have an 02 Supercrew with the 5.4. The engine starts when cold and runs fine but sometimes when I start it hot after running for a bit, it will stall out unless I keep my foot on the gas pedal. This seems to only happen on hot days. It was about 90 F here yesterday and I drove it to a shopping mall after supper - maybe 5 miles. It sat for maybe 20 minutes and when I re-started it, it stalled out.
The tach needle just drops slowly to zero and the engine stops. It will re-start without any problem but will only keep running if I keep my foot on the gas and keep the revs up a bit. It has done this a few times in the past few years and only on hot days after it has been running and then sat for a few minutes.
What I should look at? It does not throw any codes and generally runs ok after a few minutes. For example, last night I managed to keep it going by shifting into neutral when required until I got back on the road. I drove 2 or 3 miles and at the next light, it acted like nothing happened.
Ford F-150 - 1997-2003 :: Loud Popping Noise Almost A Clunk When Making A Slow Sharp Turn
Lariat stepside, 5.4L with 150k miles. Loud popping noise, almost a clunk, when making a slow sharp turn. Put it on jackstands and did the normal tire grab and shake and found no issues there. Tie rods, ball joints and sway bar links all seem tight. Looked for signs of unusual rubber to metal and metal to metal wear and found nothing. The only thing I did see was the rubber boots on the upper control arm ball joints were split. What I have checked or if I am missing something?
View 9 RepliesFord F-150 - 1997-2003 :: 2002 - Brake Pedal Goes Half Way To Floor?
2002 F-150 4x4 w/ 5.4 v-8. Brake pedal goes half way to floor before it starts to stop the vehicle. I have replaced and bled the master cylinder, bled out all of the calipers, and the calipers are installed correctly because the bleeder screws are at the top on all of them so no air can be trapped up there. The truck seems to stop fine, but just takes more pedal to get it to start stopping than I'm comfortable with. Could the ABS unit need bled out too? Or could it be an adjustment issue with the booster rod?
Also, something else I noticed, and it may be related..the ABS unit usually makes a slight clanking sound (like someone kicking a metal garbage can) a couple seconds after the key is turned on. I know its the ABS unit because a couple weeks ago I had a friends scanner hooked up to the truck, and I went into the ABS computer to clear the codes (have ABS light on from what I found to be a bad sensor wire on the front drivers side according to the scanner) and as soon as i cleared the codes on the ABS, it made that sound. I don't know if maybe there is something wrong with the ABS actuator, or if it's related to the brake pedal issue.
Ford F-150 - 1997-2003 :: 2002 - 4x4 Does Not Engage When Shift The Lever On The Floor
4x4 wont work, when I shift the lever on the floor it doesn't engage so i bought two new solenoids.. didn't work, have power on both solenoid connections. If I unhook my vacuum lines from the solenoid, I can push the Actuator rod in making my 4x4 work. I've gone threw everything.. have vacuum, have power on my solenoids. Just nothing works when I shift into 4x4 on the floor.
View 3 RepliesFord F-150 - 1997-2003 :: 2002 - Brake Pedal Fade / Started Going To Floor When Stopped
Last week my brake pedal started going to the floor when I stopped, it still stopped and felt fine on the top half of the pedal travel but then it would just slowly fade to the floor. I took it to a local shop and they said the master cylinder was leaking internally and my rear brakes were shot. I have 75,000 miles and the rear brakes were original so I told them to fix it. This is basically what I expected it to be.
They kept thinking they were getting defective master cylinders but after the two Napa parts and two Carquest parts they realized they misdiagnosed it and said I needed to take it to the dealership. I paid for the rear brake job since it needed done anyways and have an appointment for next week at the dealership. What might be causing the problem? I see no brake fluid leaks, no vacuum leaks, the booster was replaced 25,000 miles ago due to noise, no ABS light on, no CEL on, no other symptoms.
Ford 6.7L Power Stroke Diesel :: Loud Clunk When Shifting Into 4x4
So I took the wife to the pumpkin farm today, and was we were pulling into the grass/mud parking lot, my tires just started spinning. I stopped because I wasn't going anywhere and I turned my truck to go into 4x4(SOTF) and it made this LOUD clunk and then went into 4x4. Everything is ok and I tried it 4-5 after that to see if it would keep making that noise and it did not.
View 14 RepliesFord F-150 - 1997-2003 :: 2002 - 1000 RPMs At Stop Sign And Clunk Sound
My 2002 F-150 with the 5.4 has an issue with a high rev (1000 RPM for a few seconds) while at a stop sign, along with a clunking/banging sound coming from under the truck. This is when I have the brake mashed all the way, and this all happens at the same time, almost every time I come to a stop at a stop sign or light. I do have an intake manifold leak, which i have recently determined, but I do not know if the high rev at a stop sign has to do with the manifold leak or to do with the transmission sounding thump I hear. Could this be a torque converter not unlocking, and then suddenly unlocking? Because after the thump sound, the RPM's go down to around 650 from 1000 every time.
View 4 RepliesFord Super Duty (1999-2016) :: Clutch Slipping - Harsh Shifting - Loud Clunk Noise Into Gear 2 Then 1
New truck 11000kms ago thats done medium amount of work but nothing heavy or sustained for long periods of time. I get the feeling of clutches slipping especially when truck is cold but also when normal temps. Doesnt make any weird noises or anything. I can really notice the difference in torque if in manual mode being much better, but still not perfect if i stomp on the gas pedal and go through the gears in manual mode will still slip. Also is really harsh shift if i come to a halt in 3rd manual mode with the brake pedal depressed push minus button the truck makes very loud clunk noise into gear 2 then 1. Took it to ford they couldnt find anything ? Thinking of trying another dealer.
View 2 RepliesFord Super Duty (1999-2016) :: 2002 F250 - Clunk In Front End / Felt In The Floor And Steering Wheel
I have a 02 F250 4x4 5.4. As I drive and when pulling into a driveway I hear a clunk that can be felt in the floor and the steering wheel. I've replaced the wheel bearings and seals, shocks, ball joints, sway bar links and bushings, tie rod ends at the gear box and "right hand inner". The other two tie rods are tight and so is the track bar. I cannot duplicate the sound if I jack it up and move parts around with a pry bar. I can however move the steer box sector shaft upwards about an 1/8. I've adjusted the screw but it didn't do anything. Could it be the steer box or the springs? I've even mounted a GoPro underneath but everything moves and I can't tell why it is.
View 14 RepliesToyota - Dolphin :: 1977 - Loud Clunk When Shifting Into Reverse Gear
Sometimes when putting the vehicle into first it's almost impossible to get it to go into gear. Sometimes it's super smooth. Also when putting into reverse we hear a loud clunk. That one is most of the time but sometimes it goes in smooth. I was doing some looking around at the pedals because I think I am going to have to replace my master cylinder and noticed that on the inside of the vehicle where the clutch master cylinder comes into the vehicle it's leaking black fluid. Does that automatically mean my clutch master cylinder needs to be changed? Could this be the cause of it being difficult to shift because the clutch isn't fully disengaging?
View 11 RepliesHonda - Pilot :: 2003 - Shuttering Sound That Vibrates Through Front Floor Boards
I have a 2003 Honda Pilot with 117,947 miles on it. When I reach 40 mph there is a shuttering sound that vibrates through the front floor boards. Took it to a Honda dealer and they could not duplicate the issue. It happened intermittently. Does not appear to be related to outside temperature or level of gas in tank. What the issue may be for the shuttering?
View 3 RepliesCorolla / Matrix 2009-13 :: Auto Transmission Has A Loud Clunk When Down Shifting On A Hill
We have a 2009 Matrix, 68000 miles. automatic transmission has a loud clunk when down shifting on a hill. Has only happened a few times and cant seem to make it happen. Am really concerned what this might be.
View 5 RepliesFord - Explorer :: 2002 - Loud Clunk Noise When Put It In Reverse
2002 ford explorer 4x4 150k miles when i put it in reverse a loud clunk noise but when put in drive no clunk noise. But on highway when its shifts a very loud clunk and like a real hard shift !!!!!o/d light is flashing also .transmission shift solenoid ? rear ?
View 8 RepliesFord F-150 - 1997-2003 :: Vibrates While Driving - Is This Normal?
just curious if this is normal? My trucks been vibrating when I drive it and my mechanic says it's normal
View 10 RepliesFord F-150 - 1997-2003 :: Shakes When Foot On The Brake Idling
I've owned the truck for 8 months, did a fair bit of maintenance in the first two months (plugs, tranny fluid change, maf cleaned, o2s replaced), 320,000km runs very well, no codes.
When the truck is in gear and I put my foot on the brake after a second or so idling, the engine shakes. Releasing the brake, the shake stops, but it does it every time. Also, the belt or one of the pulleys will squeak a bit at the same time, but only idling with the brake on.
It doesn't seem like it is a serious problem, but what and why? My instincts are telling me it may be transmission related.
Ford F-150 - 1997-2003 :: Start When Put Foot On Brake / Selector In P But Will Not Shift
Put foot on brake, selector in P it will start but will not shift.
Put foot on brake, turn key on, put selector in N it will start and shift R or D as normal EXCEPT do not shift to P as it will lock up and you have to start all over again.
Selector is basically aligned on the letters appropriately.
2001 F150 supercrew 5.4
Golf IV / Jetta IV :: 2002 - Loud Clunk When Going Over Bump
I've had my 2002 Golf GLS for about a year now. It has 127k on it and I absolutely love it! Saves a lot on fuel driving 100 miles a day for work compared to my Ram 2500 diesel!
Anyway, lately ive been hearing what I can best describe as a "clunk" or maybe the sound of metal hitting metal when I go over a bump. From what I can tell it sounds like its coming from the front passenger side. Maybe the rubber grommit on the strut tower is gone? I havent really checked it out becasue I havent had much time on my hands lately.
Also, ever since I have had the car the engine seems to run louder than what I expected for a VW. It has the 2.0 engine in it. Is this normal? It kinda hard to explain how its running loud but when its at idle and I have the hood up it just doesnt seem as quiet as I thought a VW motor would sound.
Ford - Explorer :: 2003 - Loud Clunk When Put The Truck In Reverse And Once Hit The Gas
I am trying to track down where exactly a clunk is coming from on a 2003 Explorer 4x4(auto, hi, low). My buddy brought it by my house yesterday and i cannot pin point it. If you put the truck in reverse, once you hit the gas, it clunks pretty loud. If you just put it in reverse, let off the brake, it will not do it until you hit the gas.
I got the explorer up in the air and crawled under it. I had my buddy switch from forward to reverse, and back again. Every time he let off the brake in forward or reverse, it would clunk. The reverse clunk was definitely louder.
It does the clunks in all settings, -auto,hi,low. No flashing dash lights. The dash lights do come on accordingly. One thing he pointed out was the Auto,HI,Low Buttons themselves are not backlit anymore. Not sure if that has anything to do with it?
I cannot narrow it down as the whole transfer case, front driveshaft and front diff, shake with the clunk. U joints don't seem to have play (prying with small prybar). I then went ahead and unplugged the big wire connector at the transfer case and the clunk went away.
Ford F-150 - 1997-2003 :: 1999 - Torque Converter Vibrates - Engine Misfiring?
I have a '99 F150 w/ the 5.4 and 4R70W, with 226K miles. I am experiencing what I believe is a TC shudder after the tranny shifts into OD between approximately 40-50mph. This sounds like a pretty common problem with this particular tranny, but some of what I've read describes the shudder as feeling akin to driving over rumblestrips, but what I'm experiencing is a very sharp, bucking. Is this how the TC shudder feels, or am I actually dealing with a misfire. Btw, I did completely change the tranny fluid with Mercon V, and added a friction modifier, but no change. I also read that the TC unlocks when the brake lights come on, so I tried lightly hitting the brakes when the bucking was occuring, but it continued.
View 14 Replies