Ford F-150 - 1997-2003 :: Fuse Blown When Shift The Gear Lever To Below D
1997 F150 xlt 4x4 ... When I shift the gear shift lever to below D (2-1) it blows a fuse and I lose instruments. Replacing the fuse is not difficult, just tiresome..
View 6 RepliesFord F-150 - 1997-2003 :: Odometer Quits Sometimes / Transmission Skids Loudly / Gear Shift Lever Sloppy
The Speed Needle works fine. But...the Odometer part quit some time ago. I can't tell what my fuel Mileage is now. How to troubleshoot this problem?
Things that might affect this problem; Transmission skids loudly when going in and out of 4-OD. It could be the Torque converter clutch?
The Gear shift lever is sloppy. Doesn't fill me with Confidence.
Brake fluid warning light is on most of the time. Fluid level is up hi though. Driver door mirror control switch don't work in one direction Who on this Forum has a Switch for me?
Ford F-150 - 1997-2003 :: 2001 Won't Shift Out Of 1st Gear
I have a 2001 Ford F-150 5.4L Supercrew that won't seem to shift out of 1st gear. This morning coming out of stop light on the way to work, the truck seemed to jerk when it was supposed to shift into 2nd gear. I was told by a friend that the speed sensor may be it?
So I took the truck around the block just so I can get a feel for what is going on. So the truck shifts into 2nd, but not past that. It seems that around 30mph the RPM's go up jump up quickly to 2k+ and no shift or increase in speed. I was reading up a bit on it and came across the possibility of a TPS?
Ford F-150 - 1997-2003 :: Overdrive Button Blinking On Shift Lever
So I drive a 19 97 F150 v8 5.4 4x4 and while on the freeway I noticed that my overdrive button was blinking on the shift lever. The truck wasn't driving any different than usual, so Im just trying to figure out what this means.
View 1 RepliesFord F-150 - 1997-2003 :: 2002 - 4x4 Does Not Engage When Shift The Lever On The Floor
4x4 wont work, when I shift the lever on the floor it doesn't engage so i bought two new solenoids.. didn't work, have power on both solenoid connections. If I unhook my vacuum lines from the solenoid, I can push the Actuator rod in making my 4x4 work. I've gone threw everything.. have vacuum, have power on my solenoids. Just nothing works when I shift into 4x4 on the floor.
View 3 RepliesLincoln - Towncar :: 2001 - Intermittent Vibration When Move The Gear Shift Lever To D For Drive
I have a 2001 Lincoln Town Car that has an intermittent vibration that can be felt when seating in the car and you move the gear shift lever to D for drive. The car has 141,000 miles. It is an automatic transmission. The vibration cannot be felt when touching the steering wheel. What could be causing the vibration?
View 3 RepliesFord Aerostar :: 1991 - Shift Cable Popped Off Gear Select Lever
I have a 1991 Aerostar 2wd 3.0. I recently had freeze plugs replaced and the mechanic had to drop the tranny to get to some. Now the shift cable has come off the gear selector lever. I have googled everywhere and can't locate the procedure for reattaching it. My mechanic was doing the work on the side and charged me only labor for his assistant. He is at work right now..
View 5 RepliesFord Super Duty (1999-2016) :: Gear Shift Lever Is Loose / Periodic No Start
I think the gear shift lever is loose and so I get a no start every day or two. I remembered seeing somewhere here that there was a way to tighten up the grearshift lever to fix this problem. I did a search to no avail.
View 5 RepliesFord F-150 - 1997-2003 :: Gear Shift - Stuck In Park
I have a '97 F150 Lariat Ext cab, 5.4, 2Wd, 175K, a bit rusty but for the most part functional. Unit is parked for long periods of time.
3 - 4 years back the gear shift did not want to go into PARK and and the gear indicator was out of register. Unit would not start and I had to move shift lever to N to start. Fixed the two screws on shift plate/column per this site. Then 18 months ago same thing begin to occur but this time I used blue thread lock to hold screws in place. Still had to throw into park to get it to stay.
6 months ago shifter became very difficult to move and near impossible to get into PARK. When in PARK the interlock must have not been engaged so had to move to N or push lever hard into PARK to start.
Tired of this so I cruised the site and found several posts on taking dash apart, repairing a broken shift tube and or replacing bushings.
Battery disconnected, dash apart, cluster out, steering wheel still on and steering column still in position. Shift tube appears OK, i.e. not broken as in one post, bushings appears OK as there is no play or slop evident, but I cannot get the shift lever to move from PARK, period.
When the shift lever is pulled toward the wheel, a pawl on the tube causes a plastic or nylon arm to move about 90 degrees. It must be a stop or safety of some sort. I have not dug deep enough to see the shift plate with the two screws. At 75 I find it difficult to lay upside down to reach and hope I can get to them from the top.
Questions:
1. How do I get it out of PARK to check all things on shift tube and gear selector units?
2. Does the battery need to be connected for the interlocks to function?
3. Do I need to drop the column to check on shift tube items?
4. With a rusty trans, can the shift cable to trans connection be the problem?
5. What to look for, how to repair. etc.
Elantra MD (2010-15) :: 2012 - Car Won't Shift Into 5th Unless Manually Do It With Gear Lever
I have a 2012 Elantra Limited with about 36000 Miles. I purchased this car used with 12000 miles. I commute to work about 90 miles round trip a day mostly highway. I usually average about 33 or 34mpg. Recently, my mileage has fallen to 22 or 23 mpg and I have noticed my car having problems shifting. When accelerating normally, 1st - 3rd shift normally. Once I get into 4th, the car won't shift into 5th unless I manually do it with the gear lever or play with the throttle. If I just accelerate it will go all the way up to over 6000 rpm before it will shift. There are no problems with down shifting. Once it gets into 5th it will shift into 6th normally. There are not warning lights on and it doesn't always do it so of course when I need to recreate it I can't.
View 26 RepliesFord F-150 - 1997-2003 :: 4r70w Trans Won't Shift Past 2nd Gear
My 4r70w is having some issues. It drives/shifts fine in reverse, 1st and 2nd but wont shift past 2nd gear. Doesn't even act like it tries. No CEL. I dropped the pan yesterday and there wasn't any metal chunks or any other debris in the pan and only the normal fuzzes on the magnet and there wasn't even an abundant amount on the magnet. This is a junkyard trans that was put in before I purchased the truck (2001 F150 supercrew 2wd).
I've ohm'd the shift solenoids and they seem to be within spec (below 30 ohms) so i want to rule them out, but still thinking of replacing all 3 solenoids just to be safe. Also, the filter just fell out with the pan so I'm assuming that might be part of the problem. My next thing to check is the 2-3 accumulator and spring to see if its stuck or broken.
Ford F-150 - 1997-2003 :: 4R70W Shift To Neutral Between 2 - 3 Then Drop Into Gear
4R70W. This one is in my 99 F-150 with the 4.6. From what the previous owner told me this trans only has 13k miles on the rebuild and I believe him because the converter is bright blue and when it does shift right, the shifts are solid and fluid is very clean. Truck only has 98k miles on the body as well, so it's possible the truck did sit a while because my tires have a ton of tread on them, but they are dry rotted a bit (dated 2006 IIRC).
Issue: When the trans is cold (sat overnight) it will shift to neutral between the 2-3 shift for 1-3 seconds depending on outside temperature and then drop into gear. But it only does this for the first 30 seconds or so of driving, after that it shifts normal (although it does seem to hold gears a little longer than I would think it should on occasion and not upshift). I have only gotten it to do it once per cold start so it seems like once the trans gets any heat it's fine.
I was also thinking I was getting drain back and maybe it wasn't heat related so I dropped the pan, replaced the filter, fluid and pan seal (it had a small leak) and torqued the valve body. Two of the bolts were a little loose, but the rest were fine. Tightened them to spec and put it back together with no dice. Truck also gets pretty bad fuel mileage so I'm starting to think maybe there is some temp sensor screwing everything up?
Ford F-150 - 1997-2003 :: 2000 5.4L 4x4 - OD Hard Shift / Slams Into Gear When Give It Little Gas
I have a 2000 F150 5.4l 4x4. When I am going over 50 on the highway and I am in OD, if I let off the gas a couple of seconds later it feels as though the brakes come on because the truck slow down so drastically and when I give it a little gas it slams into gear. It feels as like there is a "gap" where nothing is engaged before it slams back in. This is a rebuilt tranny with less than 7K miles on it. I took it back once and they said it was the motor mounts. I had those replaced and still the same problem. I replaced the spark plugs 6K miles ago and the COPs 3K ago. There is 170K on the truck. I only drive about 8K miles a year.
View 2 RepliesVolvo :: Gear Shift Got Stuck In Neutral - Control Rod Loose From Transmission Lever
Volvo Automatic 1992 240 - So, just started to back out of the garage and, all of a sudden, my gear shift got stuck in neutral and then started shifting without engaging the transmission at all. Pushed it back into the space and, taking a look underneath, I realize the control rod's completely detached from the lever in the transmission.
I can re-attach it, but it just comes loose again when I shift. It seems like something should be in there to hold the control rod in place with the transmission lever, but I don't know what because I can't seem to find any documentation on what everything should look like down there.
Attaching a couple shots, one with a circle around the area that's coming un-attached since the angle's a bit off.
Attached File(s)
IMG_8972.jpg ( 1.09MB )
IMG_8978.jpg ( 938.64K )
Sonata I45 (YF - 2011+) :: Braking Noise When Coming To A Stop Near Gear Shift Lever
I have a 2011 Sonata with 4,000 miles. Recently, I have noticed that when coming to a stop, I hear a light thump noise in the center console area near the gear shift lever. If I put my hand on the gear shifter, I can feel it move ever so slightly at the time of the noise. The noise is very repeatable. If I take my foot off the brake and start rolling and then I reapply the brake (either softly or hard) it will make the thump noise. It is not very loud and can be drowned out with loud music, but if listening to news, it is very noticeable and annoying in city traffic, where stops are very frequent. I put the car up on ramps and looked underneath and did not see anything noticeable. It will probably require the center console between the seats to be removed.
View 14 RepliesHyundai - Sonata :: 2006 - Gear Shift Lever Wet / RPMs Went Up High And Car Barely Moving
I had to stop quick today. My ice water spilled into the gear shift lever. A mile down the road my rpms went up high and the car barely moving.
2006 Hyundai Sonata...
Chrysler - Cruiser :: 2007 - Won't Start Easily After Maintenance - Gear Shift Button At The Top Of Lever Sticks?
I have a 2007 Touring Edition PT Chrysler Cruiser which was just a few days ago repaired because of damage under the front of the car. Front bumper, ouside and inside grills, all housings and connecdtions in the front area were replaced, including air conditioning mechanisms. Received car on Monday, Friday evening, it wouldn't start. Just made a tet tet tet or clicky kind of noise, no turning over of engine, then there was no noise ... just wouldn't start. Got jump, still wouldn't start until the third cycle that peddle was pressed. Now I'm finding that the longer I let the car idle, the more likely it will be to start after more than two hours of non-use. Had all electrical circuitry checked ... battery's 100 percent, alternator is working fine, but it's still not starting.
Car's gear shift button at top of lever is also sticking when I put it in park to turn the car off. Have to pull the top button up to get the key out. This was happening before car was repaired underneath front. Talked to warranty person, and he felt that maybe the ignition starter switch (if that's what's wrong) and sticking gear shift may have something to do with each other. Since car is actually starting after being run, maybe it's not the starter switch. I'd hate to get it repaired if that's not what it is. Thinking about having a Chrysler dealership do a diagnostic test on it to pinpoint exactly what is going on.
What's happening? Why is my car cutting not starting in selective situations after not having been idled for a couple hours or more?
Toyota - Camry :: 2000 Won't Start When Warm / Gear Shift Lever Is Not Finding Park Or Neutral
My Daughter owns a 2000 Camry. It has a very annoying habit of not starting when it is warm (think driving to the gas station, turning the car off to fill it and then it doesn't start again). We have tried new solenoids, a new starter and several other tweaks but nothing seems to fix the problem. Recently she discovered if she jiggles the gear shift lever (it's an automatic) it will start. So, obviously she gear shift lever is not finding Park or Neutral so that it can be in position to start. She has experimented with this concept and it appears to be the only thing that consistently solves the starting issue. What would we have to fix in the gear shift lever, or elsewhere, to fix this problem?
View 5 RepliesFord 7.3L Power Stroke (1999-2003) :: 2001 F250 - Won't Shift To 3rd Gear - No Codes?
i bought a f250, i rebuilt the 7.3 after installing it the transmission isn't shifting correctly. Reverse perfect, 1st and shifts to 2nd great. wont go into 3rd. i replaced the 2 sensors on the transmission, i replaces the sensor on the 3rd member. the speedometer works but not correctly, i can unplug the sensor on the front of transmission and it shifts into 3rd. but when i plug it back it doesn't. no codes. could it be the ecm?
View 10 Replies