Ford F-150 - 1997-2003 :: 2000 Truck Will Not Start After Running For A While Then Sits For About An Hour
2000 2WD 4.6L ... I was trouble shooting why the truck will not start after it has run for awhile then sits for about an hour. I was checking the connections on the solenoid switch on the fire wall when my wrench slipped and touched both terminals on the solenoid and the engine starter kicked in. I tightened the connection then tried to start the truck with no luck. so I tried leaving the key in the "ON" position and jumped the two terminals and the truck started. Does this tell me I have a bad solenoid switch?
View 6 RepliesLexus GX 2010+ :: Idles At 550 RPM And Truck Will Barely Move Forward Even With No Brake
Before I got my GX someone posted they had to press harder on the brake to keep the vehicle from moving forward. My truck idles at 550 rpm and the vehicle will barely move forward even with NO brake. Just resting my foot on the brake will hold it easily.
View 6 RepliesFord F-150 - 1997-2003 :: Truck Refuses To Move Off Of 12 Mpg / Terrible Gas Mileage
Why I am getting such terrible gas mileage? The truck refuses to move off of 12 mpg. I made a 500 mile trip half of it at 70 mph running 2100 rpm. And when I filled up I calculated out 11.3 mpg. After that fill up hopped on the interstate and was running around 85 @ 2600 rpm expecting my mileage to drop even lower. Then i was on two lane hwy again constantly passing people and it only dropped to 11.1 mpg. Now no matter how easy I drive or how hard I drive it will not move over 12 mpg. Whether the tank is 100% hwy or 50/50. Its a 5 spd manual 4x4 with no modifications running the 4.6 v8. I just swapped air filters to a K&N and still no change.
View 8 RepliesFord A/C :: Truck Running Cold / Heat Is Barely Warm
MY 2000 Ford F150 4.2L v6 is running cold. I bought it this summer and it ran a hair above the cold line on the temp gauge. Now that it is cooling off it doesn't come off the cold line. I have drove it for an hour and it never move. The heat is barely warm. I thought it may have been a stuck open thermostat so I changed it out with a 195 and it did not work. I can let the truck run parked for 15 minutes and still be able to grab the hose leading down to the thermo. What is wrong? The guy I bought it from used it to pull a small boat. He said it started running hot when he would pull with it so he had a new radiator, thermo and clutch fan installed. Then he said the truck ran on the colder side. Now the thing just runs plain cold!
View 1 RepliesFord 7.3L Power Stroke (1999-2003) :: 2000 - Truck Won't Move In Drive?
I have a 2000 Excursion diesel 7.3. I drove it for an hour yesterday and it drove great. When I arrived home I left the truck running and put it in park. Checked the mailbox and jumped back in the truck and put it in drive and it would not move. Tried FWD and reverse. Moved a little in reverse.
I turned the truck off then cranked it back up put it in drive and it drove fine..... Took it for a test drive and seems fine.
Did the same thing today. Went to drop my kids off and I put it in park and left the engine running. Put it back into drive and it would not move.
Turned the vehicle off and back on. Put it in drive and it drove off fine.
Fluid is full, red and no burnt smell. Wondering if this is converter or electrical and how long I can drive it like this.
Ford F-150 - 1997-2003 :: 2000 - Hesitation When Tank Not Full
Recently purchased a 2000 ford f150 4.2l. started hesitating when i would try to accelerated stressed or when a.c on. if i drive it like a grandpa wont do it. filled up the gas tank and it completely went away. the second it went down to the 3/4 line, started hesitating again. mind you when it was full even with the a.c on and going 80mph on expressway it would not hesitate.
View 2 RepliesFord F-150 - 1997-2003 :: 2000 4X4 - Floor Shifter Will Not Move?
Drove to work in 6" of snow in 4H with no issues. Shifted back into 2H for drive home as roads were clear with no issues. Went to shift into 4H moments ago and floor shifter will not move!
View 1 RepliesFord 6.0L Power Stroke Diesel :: 2006 F250 - Lack Of Power / Truck Will Barely Move And Takes Long Time To Accelerate Under A Load
I have a 2006 F250 6.0 Amarillo Edition. 133,000 When I bought the truck it was a theft recovery vehicle where the turbo, injectors, FICM and wiring harness were stolen. The company I bought it from replaced the injectors, wiring harness-new, and a used FICM, and turbo. Also has EGR delete and SCT tuner with basic tunes. I believe the SCT was put on to mask another problem. No dealer would spend that kind of money to sell a truck unless something was wrong. The truck would accelerate some with the tuner but shift the tires so hard it would bark them. I removed the tuner and went back to stock program.
The truck will barely move and takes a long time to accelerate under a load. In park and neutral it is fine. A friend has a ford diagnostic program on his computer and says the readings were all good except EBP was a little high. Removed exhaust and air intake to verify no restrictions. Turbo sounded like the vanes might be sticking so I replaced the turbo and VGT solenoid. Now truck feels like its trying to make more boost but not transferring power to the engine. Have blown the silicone hose off twice now during testing. Checked the EBP sensor and tube and only thing I see is a little carbon buildup inside the sensor. What else to check. I'm new when it comes to diesels.
Ford F-150 (2004-2008) :: Truck Lost All Power / Barely Staying Running - Code P0012
2008 F150 5.4L .. The truck lost all power the other day driving and barely made it to work. On the ride home it was still running horribly, like it just fell on its face. the check engine light came on. Went to autozone and put HEAT in the gas tank cuz the night before it was at quarter tank and temp went from warm to freezing(thought maybe condensation in tank).. Truck ran a lot better( not perfect). Drove around that day and it was fine. Pulled down the driveway and CE light shut off. Ran the code anyways and it was P0012..
Talked to a few mechanics and they said try replacing the Camshaft position sensors..did so and it ran worse. the truck hardly would idle or rev and shook violently..i shut it down right away. Then it threw 9 codes..Cam shaft position- over retarded timing bank 1(P0012), misfire cyl2, misfire cyl3, misfire cyl 4, random misfire, cam sensor bank 1, three of them were repeated codes..
I replaced the sensors back to stock and cleared the codes. the truck is running like it was in the beginning of the problem..No vilant shaking but falling right on its face at idle and any rpm..not drivable. Would rather do the work myself. very capable except for replacing camshaft phasers which i have heard could be the issue..Could it by the VCT seliniod, EGR valve, plugs, wires...Did just change the oil a week ago and cleaned and reoiled air filter.
Ford 7.3L Power Stroke (1999-2003) :: Right Front Window Would Barely Move When Opening It
My right front window would barely move when I was opening it. Binding real bad on the way down. So I pulled the door panel, ( a two minute affair ) lubed all the tracks with silicone grease. Now the window goes down very easily.
I had all four doors done in an hour. To remove the door panels, remove the red reflector from the door, remove the screw underneath of it. Gently pry up on the window switch bezel at the front for the front door, and the side for the rear doors if so equipped. There will be another screw underneath. Unplug the switch, remove the screw. Remove the trip piece from above the hinge area. Push up on the panel and it comes off.
I used that real thick silicone grease that you can get a plumbers supply for lubing faucet o-rings. It looks like double thick vaseline. Windows work like a dream now.
Grand Prix :: 1997 GT Running Extremely Rich And Pressure Build Up In Fuel Tank
I'm having this weird problem with my car, 90% of the time it will start to run rich, until it reaches normal temp, to the point that I can smell it coming out from the exhaust. LTFT is at around -15% and it seems to go down after cruising for some time but will go back to negative at idle. My first suspect was the FPR so I checked it and found no gas smell on the vacuum hose, then I decided to run the engine with the vacuum hose disconnected and see if any fuel would come out, 5 minutes later and it was still dry.
There is a chance that the MAF sensor is bad, I'm 90% sure it is, because it will sometimes read 2.9-3.1 gps at idle and according to the rule of thumb of 1gps per liter of displacement, it shouldn't go that low but I might be wrong about it; I disconnected the MAF and the smell was still there, today while driving it was reading 5.45gps (A/C was on) and the smell was still present; car also feels sluggish from time to time only at normal operating temperature (which I assume is because of it running rich).
There is also a vibration felt through the steering wheel only while idling in gear at all temps. Today when I got home and after I turned off the engine I heard a noise like water was running. It was coming from the car so I tried to find where the noise was coming from and it's from the fuel tank. I removed the fuel cap and lots of air came out (or sucked in?). I reinstalled the cap and pressure started to build up almost immediately! I have a video, which I'm sharing, so you can see what I'm talking about; I was even able to hear the fuel tank expanding because of the pressure inside, not sure if you can hear it towards the end of the video (when I put the phone under the car). [URL] .....
It also happened today that I was cruising and the engine hit the rev limiter after I stepped on the gas (WOT) to overtake another car. I immediately removed the foot from the pedal and gave it less gas and it acted normal, no slipping from the transmission at any other time. There is one more thing that I'm not sure about it. Every morning, the engine will sputter for 1 or 2 seconds after starting it but it will be fine for the rest of the day. I once tried disconnecting different sensors from the engine and the only one that seemed to make a difference (it didn't sputter) was the TPS.
Things done so far:
- I replaced the EVAP purge solenoid (P0441 was present) back in february.
- Rubber pieces at charcoal canister also replaced, old ones were rotted to the point my hands would look black just by rubbing against the hoses.
- Upper intake manifold was also replaced by me in november last year.
- New NGK spark plugs and OEM spark plug wires last december.
- Cleaned the MAF sensor with MAF cleaner, no dice. Used brake clean, no change. It's a reman Cardone from autozone, which tells us it's 90% sure it's broken.
- New Duralast MAP sensor back in 2010 because a mechanic broke the original.
- 10qts transmission fluid and filter replacement 2 weeks ago.
- Fuel pump was also replaced back in 2009 maybe, can't remember the exact year. The old one would start making some kind of a hissing noise after prolonged driving.
NO DTC'S PRESENT. I once checked Mode $06 data with a mid-level scanner I have (AutoXray EZ-scan 6000) and saw a test had failed, I think it said something about the MAF and EGR. IHaven't connected my fuel pressure gauge tester. Since I can smell it running rich, I didn't think it would be necessary. I'm thinking that there could be a problem with the EVAP system that's causing the excessive pressure in the tank but I'm not sure what that could be. Is there any chance that the pressure is also causing the rich mixture?
Ford F-150 - 1997-2003 :: 2002 Truck Running On 3 Cylinders
My aunt recently gave me her 02 f150 for free because it got flooded and she didnt want to fool with it. she said it ran great before it got flooded. I flushed everything. oil, gas, and tranny. I blew water out the cylinders and replaced the spark plugs. I took the fuel injectors out and cleaned and cycled some b12 threw them. The truck starts and gets spark to every cylinder and is only running on 3. I can pull 3 plug wires off and the idle does not change. Idk what it could be but dead cylinders. I am afraid I am going to have to find a new engine. I am going to do a compression check later this week when I have time. I am new to fords so if there is anything I should check...
View 2 RepliesFord 7.3L Power Stroke (1999-2003) :: Battery Light On / Voltage Meter Only Show Barely 12 Volts At Full Throttle
The brief information:
1. Stuck/non moving in traffic on the freeway for roughly 1 1/2. During that time the AC was running, but once I noticed my "battery light" on the dash turn on, I turned everything off.
2. Since then while on my way home from work the voltage meter only showed barely 12 volts at full throttle.
3. I charged my battteries, and started it up today to go into work. While going to work the voltage meter showed 14 at its high point, but shortly there after it dropped back down to 12. At which time the battery light came back on.
New battery or alternator?
Ford F-150 - 1997-2003 :: Code P0172 / Bank One Is Too Rich
So my truck is reading a code at P0172 which means bank one is too rich. I replaced all of my o2 sensors, cleaned my MAF, and replaced PCV and hoses connected to it. What else could it be?
View 3 RepliesFord F-150 - 1997-2003 :: 1998 - Rough Running Truck When Accelerating
I have a 1998 F150 4.6 2wd regular cab with 255,000 miles on it. Lately it has had some problems. The first is that it will run really rough when under a load, meaning when I step on the gas. It runs smooth at idle and at cruise but when I step on the accelerator it bogs way down and almost shuts off. I have changed the spark plugs, spark plug wires, coil packs and fuel filter. Now I'm thinking maybe fuel pump?
The other issue is that when the truck is having to work a little harder (i.e. pulling a trailer or running in the summer with the AC on) it will start to run hot. I have changed the thermostat, flushed the coolant, cleaned out the radiator, etc. and it still does it. Could both of my issues be related to a fuel problem??
Ford F-150 - 1997-2003 :: 2002 - Truck Is Hard To Get Started And To Keep Running
Sometimes the truck is hard to get started and to keep running, Once it warms up it will run fine. The next time it is started it will start fine but when you are going down the road if I try to accelerate it will start backfiring and not pick up any speed. I am getting a lean code on both banks. I have changed the IAC, the throttle position sensor and mass air flow sensor. 2002 F150 with 6 cyl
View 1 RepliesFord 7.3L Power Stroke (1999-2003) :: F350 Running Rich / Crank Very Long Time Before It Starts
I recently (in the last few months) have noticed my truck (1999 F350 duallie) seeming to be running very rich … I pull a 32' trailer with it and noticed on the art few trips the front and right side of the trailer covered with diesel fuel spots when I got home …. It also smells very rich when idling…. The last couple times I started it in the mornings it seems to crank a very long time before it starts …it still runs but its got issues evidently … it has these 3 codes :
P1280
P0475
P1670
The 1670 will clear , but the other 2 I can't clear, they are right back every time you turn the key on …
Chevrolet - Blazer :: Barely Move Forward And Will Not Move In Reverse
My trailblazer will not move in reverse , and will barely move forward, i checked transmission fluid hot and it's not even on the dipstick but when it was cold. it was?? Do I add more or what?..
View 9 RepliesFord F-150 - 1997-2003 :: Truck Quit Running / Engine Turn Over But Will Not Start
I have a 1997 ford f150 V-6 4.2. My son was driving the truck on the expressway and it quit running. The toe truck has delivered the truck back to my house. The engine turns over but will not start. I shot gas into the engine with a spray bottle and the engine still would not start. Was going to check the coil for spark next. What to check first. Was thinking the problem could be the modulator or coil.
View 10 Replies