Ford 6.0L Power Stroke Diesel :: Long Crank Time And Starts After Sitting And Cold

The past couple of cold starts (not real cold mornings though) I have experienced long crank time to start. Once started she starts normally. No time to read but I'm getting a little worried that I'll get stuck somewhere. I'll check back with my phone when I get into an area with cel service.

View 14 Replies

Ford 6.0L Power Stroke Diesel :: 2006 F350 - Long Crank Time

I have a 2006 F350. I have long crank times. No Codes. I have Autoenginuity with Enhanced Codes and everything shows fine. I replaces standpipe and dummy plugs. Glow Plugs and harness. I was hoping it not be the STC but I needed to do oil cooler so wanted to eliminate STC. Got truck apart and the STC Fitting is newer style so I'm kinda bummed out. Not sure if I'm missing something and as far as I have it torn down is there anyway to test what could be causing the problem? Or just put it back together and keep my fingers crossed that whoever put the new STC fitting in screwed it up. I'm beginning to not like my truck.

View 8 Replies

Ford 7.3L Power Stroke (1999-2003) :: CEL On - Long Crank / Truck Starts Losing Power And Eventually Died

On the way to work, the truck seemed to have a miss at idle and the CE light came on. Long crank to start leaving work, and truck starts losing power and eventually died. No smoke while it was losing power. Towed it home and checked the fuel pump and lines for blockage and found nothing.

2003 7.3 F-250 430K miles
strong cranking but no start no smoke out exhaust
Oil changed recently
IPR changed
Both UVCH gaskets and pigtails have been repaired.
ICP sensor and harness changed, also disconnected no change in cranking.
fuel filter changed today (no oil in bowl)
3/4 tank of fuel
dash gauge for lpop goes up to normal range during cranking and oil light turns off.
WTS light comes on and turns off as normal
tach gauge moves up between 100-200 during cranking
fuel pump turns on and pressurizes system like normal and turns off.

Ordered AE for the truck, and it directed me to the passenger side bank high open. Fixed the harness on that side and still nothing.

Sent off the IDM and it passed with flying colors

So now i'm leaning towards the HPOP, but would hate to fork over the cash for it and still not get anywhere. I'm going to take the valve covers back off and check the discharge ports for the injectors tomorrow.

View 14 Replies

Ford 6.0L Power Stroke Diesel :: 2003 F350 - Intermittent Long Crank When Hot

2003 6.0 will fire within 2 seconds when cold, literally a "bump the key" and she fires up scenario. Recently and only when the engine is hot I'm getting extended crank times and sometimes it takes several attempts for the truck to start. I replaced the HPOP with an upgraded pump after the factory HPOP went out at 311,000 miles. I know this sounds like a standpipe leak scenario but it doesn't act up all the time, sometimes it fires right up even when its hot. my thinking is a leak is a leak and only gets worse.

My IPR is reading in the 26% range, FICM is steady in the 47.5 to 48 volt range and at idle 585 to 600 psi on the ICP with a good FICM sync. I'm going to to use my scan gauge and see if I can catch an extended crank scenario to see if the ICP is reaching 500 psi but is there somewhere else I should be looking? FICM relays possibly? I've noticed when i turn the key on I'll hear the fuel pump,vacuum pump but the clicking sound is very brief or nonexistent (not sure what the clicking noise is from I assumed glow plugs but its absence is noticed)...

View 14 Replies

Ford 6.0L Power Stroke Diesel :: 2007 F350 Running Extremely Rich When Accelerating From A Stop

I have a completely stock 2007 F350 turbo diesel with 98000 miles that i just bought . When accelerating from a stop, it runs so rich that it will barely move and it accelerates very slowly . It burbles excessively and spews black smoke . It slowly builds rpm . As it builds rpm it runs slightly better and the black smoke turns into a medium gray the faster it goes . It takes around 20 seconds to reach 3000 rpm on level ground with the accelerator pedal half way down . Once it reaches 3000 rpm, it runs fine and hauls a_s but looks like it still smokes a little.

The temp gauge stays right in the middle and it does not run hot . It starts and idles fine. The check engine light is on but i have not read the codes yet and can't do that until monday. I have read that it could be an injector that is stuck open but do not know how to check for that. I am a vintage car mechanic and engineer but I know zero about newer computer vehicles and very little about diesels.

View 14 Replies

Ford 6.0L Power Stroke Diesel :: How Long Is Extended Crank Time

So how long does one have to crank until it is considered an extended crank? 2 seconds, 5 seconds, 10 seconds.....?

The reason I ask is after all the motor work I did on my truck sometimes she fires up in less than 1 second of cranking and other times it take maybe 2 seconds of cranking. I do not think 2 seconds is considered and extended crank time but was just curious about what is considered extended cranking.

View 12 Replies

Ford 7.3L Power Stroke (1999-2003) :: Long Cold Crank / Hot No Start

I have a early 99 f250 super duty 7.3l and it's giving me fits. about a month ago the truck started to do a hot no start. drove truck for about a hour. Shut it off and half hour later no start. Let it sit over night and would start with long crank.

Changed CPS no change. Pulled tuner and set back to stock. No change.
Changed fuel filter, no change.

After reading forums changed IPR and truck started and ran great. About a week ago back to the same problem. Battery's are about 2 months old. Oil change and oil filter a month ago.

Checked the hpop reservoir and its 1/2 from the top.
Checked fuel bowl and it has fuel. no sign of oil in it.
Drained bowl and watch bowl fill back up. seems to fill quickly.
Pulled passside valve cover to check for bad orings while cranking.

Every thing seems fine. have not done driver side yet. used FORSCAN and ran buzzed test on injectors and they all buzzed what seems to be about the same. ran test couple of times to make sure. this morning I ran a live scan while cranking and this is what I got right before it started. ICP 660.6psi, IPR 64.84% and RPMs 227. took 8.86 seconds to start. after work scaned again for hot no start and this what I got. ICP 292.9psi, IPR 55.86%. and RPMS 203. unplug ICP and no change. still will not start. one thing I did notice when plugging ICP back in I looked down in side at the pins and can see what seems to be bubbling around one of the pins. the pig tail has just the slights sign of oil.

View 14 Replies

Ford 7.3L Power Stroke (1999-2003) :: 2002 - Long Crank Even Plugged In

Little background- this is my first winter in a diesel truck. When I purchased it- it had 4 glow plug codes. Everyone around me just told me to plug it in and fix it later, that if I plugged it in, glow plugs don't matter much.

Had hard starts all last week with temps down to -20, turns out my block heater wasn't turning on due to a bad cord. Replaced cord end today. Let the oil temp get up to around 60F according to torque pro.

Still had a long crank despite warmer oil (15ish outside). Batteries dip to around 10V when plugs are on, then cranks at around 11V. Lots of white smoke which I know is normal.

I still had to fight with it a little bit to get it to start, as soon as she was actually going- runs flawlessly, no lope, no smoke. Runs and drives flawlessly. If I turn it off, she fires right back up instantly every time without hesitation, until she cools off again.

From what I'm seeing I'm thinking my batteries are fine, and my starter is probably fine. Are glow plugs making this big of a difference even though the truck is plugged in?

Truck has 0 codes when warm, 0 blow by, drives fantastic, Just under 300k miles. The only thing I'm thinking of is the glow plugs need swapped. I have a set of ZD11s sitting in the truck waiting for a warm day.

View 6 Replies

Ford 7.3L Power Stroke (1999-2003) :: Repair Of High Oil Use And Long Crank?

Parts came from Riffraft Diesel Performance. A set of "o" rings for the injectors. High flow CVD fittings for the fuel lines. Turbo rebuild kit. (its got 210,000+ miles) Anti Surge compressor wheel.(ok its not part of the oil problem)

Photos to come. I will take during the rebuild.

View 14 Replies

Ford 7.3L Power Stroke (1999-2003) :: 2001 E350 - Long Crank Before Starting

I have a 2001 E-350 w/7.3. When I start the truck first thing or when engine is cooled down it starts fine. I checked the high pressure pump pressure and it is 500 - 600 psi start up great. But when engine warms and try to start it it has long crank before starting. I checked pressure and it is between 425 to0 450 and takes awhile for it to get to 500 or better. Is this a cause of the high pressure oil pump ? I changed the oil and still does same thing. Also I noticed that after engine is hot and I try to start it, while cranking the engine the oil gauge does not move. I don't know if it supposed to when you crank it or not. I thought on other 7.3's I've worked on that the gauge builds up pressure....

View 14 Replies

Ford 6.0L Power Stroke Diesel :: Long Crank Time To Start After Oil Rail Removal

Removed my oil rail to replace standpipes/dummies (04 Wavy rail) and now I have huge crank times to start. This is after the initial Huge crank to get it started. Do I have air in the system, or did I bugger something. I did the whole deal very careful. I lifted the rail up very carefully, pipes removed. I lined up the rail nipples with the injectors and evenly pressed it back in place, and then inserted my dummies/standpipe. Tightened the rail to 120 inch lbs then the dummies/standpipe to 60 ft lb. I did my son's '06 a month ago with no troubles. (didn't remove rails though). Once running it sounds perfect, turn it off and re-start and it's a long crank (30 seconds or more). I have not monitored ICP/IPR while running, will try that today.

View 8 Replies

Ford 6.0L Power Stroke Diesel :: 2005 F350 - Long Crank Times

So my recently purchased 2005 f350 has an abnormal long crank. I searched all the internet and everything pointed to STC fitting. Well I knew I had some other things I wanted to knock out so I ended up buying an update kit from sinister diesel. It included an updated fitting, new degas cap, updared turbo oil feed and return lines, blue spring update, and "dummy" tubes or something like that.

During the last few days I have removed the turbo, and finally got to the hpop. As I was removing the turbo I thought I might have the updated lines as there was no braided area in the feed tube. Sure enough I pulled the hpop and I have the one piece fitting. So now that I have wasted all this time removing all this stuff for no reason I still don't know what is causing my long crank. I am going to probably install the new fitting and lines anyway but where do I go from here?

View 3 Replies

Ford 7.3L Power Stroke (1999-2003) :: Truck Stutters On Road After Long Drive When Running

This is wife typing in middle of trip. Today we drove almost 300 miles down the road before it stuttered. We lost the tach but nothing else. No check engine lights. It has done it a few times since. Watching with Torque and don't see anything there. Have 100 miles to go and it's happening more frequently. Replaced CPS 4 weeks ago with a Ford grey. Running down road it's 95 day. Oil was checked to be good at 211, transmission 182, EGT 790, pulling enclosed 6x12 cargo trailer. What can I check?

View 14 Replies

Golf/GTI VI :: 2013 - Long Crank Time Before Engine Starts?

I own 2013 Mk6 GTI. I am having to over crank the engine for a period of 8 seconds or so before the car starts, especially after it has been sitting for a few hours. My thought was a faulty check valve in the fuel pump. I have heard that our fuel filter has a built in pressure regulator that may get stuck open for whatever reason and that may also cause a long crank time.

View 9 Replies

Dodge - Ram1500 :: 1998 - Crank For Long Time Until The Car Starts

I have a 1988 Dodge pickup 1500 with a 5,9 gas engine. It used to pop right over all the time. Now, in the morning, I have to crank it forever until it starts, and if it sits for 1 hour or more, same thing (have to crank for a long time). It is my understanding there is a valve called a one day valve that holds pressure on the gas line. Is it possible this valve is not working properly? And if so, do I have to replace fuel pump to fix problem? once started it starts up with no problem until it sits for hour or more then hard to start.

View 15 Replies

Ford 7.3L Power Stroke (1999-2003) :: F350 Won't Crank At All / When Turn The Key To Start Power Drops

New to the forums, not new to fords. 1999 F350 7.3L Diesel. This has been a work truck and has seen multiple devices in and out over the years. I removed the last crap for GPS tracking etc from the last owners. The truck has worked well for a long time since until...

I'm moving slowly to a different state and so the truck got parked for 2 months. went to start it and nothing. the dash comes on and all the lights come on but when you turn the key to start the power drops and nothing.

Testing so far:
replaced the fender Solenoid
tested the starter motor and solenoid -passed
replaced the ignition switch
tested continuity of the hot and ground wires to the fender and starter and everything passed

When I shorted across the fender solenoid the starter works and tries to start the truck (unsuccessfully so far)

So the wire that goes to the fender solenoid is not working and where to trace it to and what needs to be fixed. Is there a relay or fuse besides number 30 that is in the way? where does the magical wire go so i can check its continuity?

I am stuck 800 miles from where i need to be and I am stuck here. I don't have the cash to get a mechanic and my mechanic friends are stumped. I do have a Snapon modus tester, what to do with it.

FYI the batteries are new and fully charged.

View 14 Replies

Ford 7.3L Power Stroke (1999-2003) :: 2001 F350 - Crank But No Start

I've replaced the alternator and starter recently and both batteries and the truck ran fine befor that. But it sat for roughly 2 months and now it seems as if its not getting fuel. Will start with a shot of ether but will die as soon at it burns it off

View 14 Replies

Ford 7.3L Power Stroke (1999-2003) :: 2000 F350 - Crank But No Start

I have a 2000 F350 7.3 ... A couple weeks ago I noticed that it was taking longer to start then it should be. Now I have to cycle the key switch 3 or 4 time to get it to start. There is a clicking coming from the relay block under the radio. Sometimes the truck will start sometimes it has to be rolled off. I have recently replace the starter and alternator. I have had the batteries tested and they are good. I replaced the two small relays in the block under the radio, one is for the fuel pump and the other I understand is for the door locks? I also read on here the large blue one is for the turn signal so I have not changed that one. After all this I still have the same problems.

View 9 Replies

Ford 7.3L Power Stroke (1999-2003) :: F350 Will Crank And Run But Shuts Off When Gets To 150 Or 180 Degrees

I have a 99 f350 Ford 7.3 service truck. It will crank and run but when it gets to 150 or 180 degrees it shuts off and will not crank back until it cools off. I have change the ECM I have change the IDM still same thing it runs till gets hot and then it cuts off. I have changed IPR valve IPC sensor .check the high pressure oil pressure it is around 800 900 at an idle it is around that pressure but when first starts up it is higher once it starts and runs it idles around that pressure 800 900 psi....

I have hooked up my scanner and it shows around 150 degrees oil temperature it shuts off . The high pressure oil stays the same as it was when you first crank it the low pressure crankcase oil is 60 psi ... Once the oil temperature reaches around 150 ~160 degrees the engine will shut off . Once you let it sit overnight or for several hours it might crank up ....

View 2 Replies