Ford F-150 - 1997-2003 :: 2002 V8 - Misfiring / Exhaust Is Smelling Very Rich / Idles Rough And Stalls
2002 f150 4.6l v8... Truck is misfiring and the exhaust is smelling very rich, I have new coils and plugs, it also idles rough and stalls if i let it idle for more than a couple minutes. Could it be something with fuel delivery system?
View 1 RepliesFord - Taurus :: 2002 - Rough Idle / Misfiring During Operation?
I just recently purchased a used taurus and was experiencing rough idling and misfiring during operation. I replaced the EGR valve, the egr sensor, coil pack, spark plugs, iac valve, as well as check for vacuum leaks near all the hoses. I am a novice when it comes to this, but I was able to change those without issue. The misfiring was fixed during driving, but I still have rough idling. The needle seems to stay in check pretty well and the check engine light isn't on, but the car kinda hesitates and it causes the car to rock when idling. You can also feel the stuttering and rocking when cruising at very low speeds (5-15mph). I've already plugged in a decent amount of money into parts and am running out of patience when it comes to fixing what is a "potential" problem, and it winds up not fixing much.
View 5 RepliesFord F-150 - 1997-2003 :: 2002 V8 - Rough Idle Only When Cold - O2 Sensor?
So I recently acquired a 2002 F-150 4x4 super crew with the 5.4 V-8. It idles rough (surging from 400 - 700 rpm) when cold, and sometimes dies, but more often then not it stays running. It runs and drives fine when the accelerator is pressed and when going down the road. When it gets up to operating temperature, and has been there for a while, it seems to idle fine 95% of the time. The codes I have are P0136 (bad circuit to O2 sensor), P1151 (HO2S detects lean mixture or something like that), and the infamous P0171 and P0174, which is lean exhaust/mixture on both banks. Now I have read extensively on the internet about these symptoms and have done the following:
Sprayed every vacuum hose with carb cleaner, and even around the intake manifold and injectors.
Considered the IAC (its new, the guy I bought it from replaced it a couple months ago) Torque app for android phone says vacuum is good. Cleaned the MAF and air temp. sensor with electrical cleaner Checked all of the vacuum hoses on the engine by pulling them off
Put grease around the fitting where the PVC valve attaches to the valve cover. Seemed to make it idle a lot better after messing with it, but I don't know if it was a result of the engine being fully warmed up, or my messing with the PVC.
What to try next? I'm close to just dissecting the top part of this engine and seeing what the intake manifold gasket looks like..or could it really be an 02 sensor?
Ford Ranger / B-Series :: 2002 - Rough Idle Codes / Cylinder 2 And 3 Misfiring
I have an 02 ranger xlt 3.0, it started having a rough idle, codes say cylinder #2&3 misfiring, changed plugs, wires, coil pack, didn't work, still same code, checked injectors on right side, all 3 had ohm reading of 15.8-16.5, the injectors were clicking like they are supposed to, sprayed carb cleaner around the intake ports, didn't change the idle at all,what else can I check or do? with out tearing the engine apart, unless of course I have to, the truck has been very good to me, it's got 205,000 miles on it, I need it to last at least another year...
View 4 RepliesFord F-150 - 1997-2003 :: 2002 - A/C Causes Rough Idle And Stall / Sputter And Die On Restart
I have a 2002 4.6L FX4. When I run the A/C for an extended period (say 15-20+ minutes), it will start to cough and sputter and eventually just die. It will restart but run rough and cough, sputter, die.
If I turn off A/C and let it set a while, it runs fine. No check engine light. Possible EGR problem????
Ford F-150 - 1997-2003 :: 2002 Truck Started To Idle Very Rough - Codes PO308 And PO316
My truck started to idle very rough. I pulled the codes and I got po308 and po316. First I changed plug #8, the electrode was nearly gone. I have never seen a plug in worse shape. Replaced that plug and fired it up, it still idled rough and threw the same codes. Next I moved the #8 coil pack to the #1 location and vice-versa, still the rough idle and same codes. Then I moved the #8 injector to the #1 location same results. Finally I tested compression in the #8 cylinder and it read 32psi ( not good) everything else read 150 to 160 psi. Squirted some oil into #8 and no difference in compression.The truck is a 2002 with 184,000 miles, it burns a quart of oil every couple weeks but still is in perfect shape. Should I bite the bullet and invest in a remanufactured engine for 2500.00? I put one in my 97 f 150 a few years ago with no problems.
View 5 RepliesFord F-150 - 1997-2003 :: 2002 - Rough Idle - Hesitate While Accelerating - Replacing Coils And Plugs?
I have a 2002 f150 with the 5.4. Its got a rough idle and a bit hesitant on acceleration. Im wanting to replace the coils and plugs but what brand of coils should I use?
View 3 RepliesFord F-150 - 1997-2003 :: Rough Idle At Start Up
I just acquired a 2003 with 5.4 L. Did all new plugs and coils, cleaned MAF sensor, changed air filter, oil, transfluid and filter (obviously not related).
Upon start up and idle the truck has is rough, enough that it will vibrate the whole truck SLIGHTLY. Once in gear and warm, it smooths out and is fine. Unit the next stop and start.
Ford F-150 - 1997-2003 :: Idle Very Rough Like A Misfire
I got a 97 f150 4.2l from my neighbor. he takes good care of his vehicles. he sold it to me cuz it started to idle very rough like a misfire. it is hard to start when cold spits sputters and pops. once started idles like it wants to stall, then will idle normally then back to rough. back and forth like that. runs like a champ when going down the road . check engine light was on took it to auto store they checked codes . said bad o2 sensors so i changed them. still same issue. neighbor changed coil packs checked spark plugs and wire. every thing fires good. i changed iac. still didn't fix problem. could this be a bad egr valve or sensor? if so how can i diagnose this? he also thought was a clogged cat and bored it out. tight budget can't afford to take it to a mechanic. Was told spray carb cleaner spray around engine to check for leaks that did nothing at all...
View 14 RepliesFord F-150 - 1997-2003 :: Rough Idle When In Drive
I bought this truck used and when it's in drive the engine idles rough and seems about to stall when the ac is on at a stop sign or red light.. I've tried it w/o the ac on and it seems a little better but not as smooth. Idle in park is fine.
When I should start looking? Spark-plugs? spark plugs wires, disturber cap, fuel filter etc...
Ford F-150 (2004-2008) :: 5.4 3v - Rough Idle / Stalling And Misfiring
I recently bought a 05 f150 with 5.4 3v and 195k miles needing some work. Ran great, just had a code for timing over retarded. Originally it had a cracked timing cover, so i took it off to replace and found broken guides and bad tensioners on timing. I installed new guides, chains, and tensioners, and cleaned phasers, and put back together only to find it ran terrible and had a phaser rattle. I then went in and installed phaser locks, which took care rattle but not the running issues. I can not figure it out.
ISSUES: My issues almost mirror what is said in this thread here, but this issue was never solved. [URL] ....
My issue is when started cold it starts right up, idles ok, runs ok, although a bit sluggish. Once its warm it stalls at idle, shudders when giving throttle in overdrive, and if you kick it down it will continually backfire, and slowly accelerate... it kicks down but acts like its only getting 1/8 throttle, just kind of hangs at the same rpm and slowly climbs in rpm. Sometimes it wont backfire as much, and sometimes the check engine light flashes. After it stalls at idle and you start it back up it sounds like it shudders/backfires for a split second then starts.
It is throwing many engine codes, but most are from the phaser locks. Throws code for timing over advanced on each bank (phaser locks lock them fully advanced), cam timing codes for each bank, and then a code that doesn't have to do with the timing, P2106. I am going to run some live diagnostics on it today and report back but I am fully at a loss.
Ford F-150 - 1997-2003 :: 2000 - Rough Idle When Outside Temp Below 50
2000 Ford F150 1/2 ton 2x 5.4L... Last year, I started having a problem where when the temp dropped below 50 degrees outside, my F150 would idle really rough and sometimes stall out. The CEL came on and reported some codes that I don't remember but pointed to bad air/fuel mix. I consulted a friend and he suggested changing out the IAC. I did that just towards the end of the cold weather spell we were having and the engine ran great so I assumed it was fixed.
Well, the temps have been below 50 for 8 days now and ever since the temps dropped the problem has come back. I took it to AutoZone to have the codes read and they gave me the following:
P1151 - Lack of O2 switches -bank 2 sensor 1 : ECM could not adjust fuel trim because of a lean or rich condition
AND
P0171 - Fuel trim bank one condition : The powertrain control module uses the oxygen sensor to calculate the Air/Fuel ratio of the engine. The computer recognized a rich or lean condition on one engine bank only.
Both printouts that they gave me mentioned the following:
Poor fuel pressure
Bad or Malfunctioning MAF sensor - Dirty/defective
Oxygen sensor defective
Fuel injector problem - Leaking or fuel pressure high/low
Vacuum leak on engine
I again called my mechanic friend and he suggested cleaning the MAF and if that didn't work replacing the MAF. I cleaned it and the problem was better but still not fixed.
Ford F-150 - 1997-2003 :: Engine Went Into Rough Idle / No Acceleration
I have a 2000 F-150 5.4 L. I was driving from home and seconds after the engine went into a rough idle that wouldn't let me accelerate. I scanned it and gave me multiple transmission trouble codes, about 15. I checked the wiring, the transmission fluid and it all looked good. So, what could be the problem?
View 3 RepliesFord F-150 - 1997-2003 :: Rough Idle / Engine Vibration
Bought the truck knowing it needed a little work because it sounded like a diesel when running. So I had the timing chain, tensioners, water pump, etc. replaced and that fixed that problem. Then, a couple days later, a spark plug blew out of the engine. So, I go to do a full tune-up to find out that 3 of the 8 cylinders already had heli-coils in them.
I pulled those three and bored out and re-tapped the cylinders using the Cal-Van inserts. This has worked beautifully so far. I also replaced all of the other plugs as well with double platinum plugs. I also replaced all COPs. This got the truck running again and it drives great. No loss of power whatsoever. It just runs like a dog at idle. As soon as I give it throttle it smooths out completely.
It seems like the problem gets worse as the engine starts to get up to normal operating temp. Basically, if I am idling, in gear or in park, the truck shakes pretty bad. It kind of feels like it's starved for fuel or barely missing. I do not have any codes though and if it is a miss, it is completely gone under throttle.
Other things I have replaced within the past couple of weeks:
EGR
EGR vacuum solenoid
DPFE
Both PCV elbows
PCV valve
Air filter
Harmonic balancer
Other things I have done:
Cleaned IAC
Cleaned throttle body butterfly (including EGR ports)
Checked TPS voltage
I'm sure there are other things that I am forgetting.
The idle seems low to me but I'm not sure what is considered standard for the 5.4l. Mine idles around 600 in park once engine is warm and the needle doesn't move despite the roughness felt. Just going by the tach, you would think that the idle was smooth as silk.
Truck info:
2000 Ford F-150 XLT
5.4L V8 2V
150k miles
Ford F-150 - 1997-2003 :: Rough Idle / No Power Under 2500 RPM
I bought a 99 f150 lariat 4x4 with the 5.4 from a guy who said that it needed an oil pump. He said it lost pressure coming into work, he turned it off and coasted in. I towed it home and replaced the battery and bought a new oil pressure sending unit just to be sure it wasn't that.
Those things are so hard to get to. Finally I got an oxygen sensor tool on it and it was only hand tight. Rather than take it off I just tightened it up and started the truck. The dash guage read normal but the truck was idling so badly. Steady at about 1000 rpm and tooth rattling. 1500 with the foot on the pedal it evens out but still rough. Not sure if this was a good idea but I took it around the block. No power under 2500 rpm. Barely moving even. Just felt like there was no throttle response at all and again very rough.
Got it home and parked it. Now I'm wondering what to do to fix the Idle and power problem. Where to start would be great. And input on the oil pressure sending unit too. I suppose I'll have to get under there and replace it at some point anyways.
Ford F-150 - 1997-2003 :: 2010 - Rough Idle Under Load
My daughter has a 2010 F150 with 5.4, when pulling her horse trailer or extended idling her truck starts running rough, so far her husband has changed the fuel pump and 2 coil packs, no luck.
View 3 RepliesFord F-150 - 1997-2003 :: Rough Idle And A Miss While Driving
I recently inherited a 99 Expedition 5.4 with 90k miles. I'm trying to fix it up so I can sell it. Like the title states, the truck runs rough but there's no check engine light on. I did some research and ended up replacing the PCV elbow and that made it run better for a while but now it's back like it was. It won't die, just a really rough idle and a miss while driving. I imagine it's probably a (or a few) coil pack(s), but I have no way of knowing which one(s) to replace. I would think that would illuminate a CEL though. I'm also having problems with the AC. Upon inspection, I found that the compressor clutch assembly was completely gone from the front of the compressor. I replaced the whole clutch assembly, then voided the system of Freon and refilled it to spec, still no cold air. The compressor clicks on and off like it's low on Freon but it can't be. I'd just sell it as is but in south Louisiana a working AC is a huge selling point!
View 1 RepliesFord - Explorer :: 1999 - Misfiring - Shaking - Rough Idle - CEL Flashing?
My 99 Explorer XLT V6 SOHC has been misfiring lately. In idle the RPM needle fluctuates a bit and the vehicle vibrates and shakes. At night when the lights are on I notice them dim a bit as the engine struggles in idle. It doesn't stall very often at all. Accelerating I notice way less power and the engine studders. That's when the engine light comes on flashing. Then remains on solid afterward. I brought it to a mechanic friend who read the code and it was cylinder two misfire as well as the O2 censor.
I replaced the plugs and leads and censor. Noticed the plug in cylinder two had little to no gaping. Thought I had fixed the problem. The vehicle ran perfectly. Three or four days later driving on the hwy same problem came back. Thinking it must be the coil pack I got one for a good price and replaced it. Again, the truck ran great for four days and now the problem has returned. Same thing, shaking studdering and flashing engine light. I have verified the locations of the wires and plugs a few times so i believe they are all properly installed.
Ford Ranger / B-Series :: 2002 - Running Rough Like Misfiring
My ranger just started running very rough. Like misfiring, but I think it may be the fuel pump. It starts and drives...but it surges then drives normal, as if fuel is being fed, then starved, then force fed etc. My father asked if I had trouble starting it and to be honest in the last 6 months it was a little harder to start on several occasions. On a few occasions it required more cranking. But that was only a few times.
I tried putting in a fuel injector cleaner and 93 octane gas but it is still running even rougher now. I changed out the fuel filter under the rail about a year ago (maybe 8000 miles ago at most). My father thinks the fuel pump is shot and he laughed because his went on his expedition and he said it is inside the fuel tank and there is no way to get at it without dropping the tank. Is that true? 2002 ranger xl 4cyl