Ford F-150 - 1997-2003 :: 2000 - Transmission Miss Between 45 - 55 MPH?
My dad has a 2000 F-150 with the 4.6L with 90,000 miles. He just had the transmission rebuilt 5,000 miles ago if that. It seems to miss between 45-55 mph when you have a little hill and give it some gas. Once its shifts out of over drive, it seems to be better. With over drive off, it does not miss as much. I know we put new plugs in it but don't remember how long ago it was. He bought the truck brand new.
View 2 RepliesFord F-150 - 1997-2003 :: 2002 Truck Won't Shift Into 2nd Or Drive
Today at a light my truck wouldn't upshift. I can manually shift from low to second but not to drive. Reververse works fine. I was noticing a slight slip between 45 & 55mph and would sometimes go away if I disingaged the overdrive.
View 2 RepliesFord F-150 - 1997-2003 :: 2000 - Drive Line Vibrating?
t's a '00 extended cab swb 4.6L with 4r70w trans. I have a Hotchkis TVS 2/4 kit on it. It's been lowered 3 years now and I've never had any real issue. But I started noticing a small vibration through the floor so I took my driveshaft out to be balanced and new U joints installed. Ever since then I've had an audible "hum" from the rear whenever I go over 75mph. It only does this under load (hill, etc) and I don't hear anything until then. The driveline shop told me it was my pinion angle and I've tried shims with only slight improvement. I'll replace the driveshaft after I do a motor and trans swap down the line, but it's out of the budget for now.
View 2 RepliesFord F-150 - 1997-2003 :: 2000 - 4 Wheel Drive Will Not Disengage
I have a 2000 ford f-150 4 wheel drive that will not disengage, I am down here in south fla where and don't put it in 4 wheel drive much, but yesterday I put in 4 wheel drive and I heard the click click and it engaged I put it in drive and drove it about 5-10 miles parked it and turned the switch to 2 wheel high and got out , got back in the truck turn her back on and the 4 by 4 lamp came one went off then came back on and stayed on and it still in 4 wheel drive and wont disengage.
View 4 RepliesFord F-150 - 1997-2003 :: 2000 - 4 Wheel Drive Isn't Engaging Properly?
I have a 2000 F-150 4x4 and the four wheel drive isn't working properly. It does work,but to get it to engage I had to drive in reverse for a couple feet then it locked it and everything was fine,pretty sure that isn't normal. What could be wrong with it? As soon as I turn the lights up on the dash,but the front tires don't spin.
View 1 RepliesFord F-150 - 1997-2003 :: 2000 5.4L 4x4 - OD Hard Shift / Slams Into Gear When Give It Little Gas
I have a 2000 F150 5.4l 4x4. When I am going over 50 on the highway and I am in OD, if I let off the gas a couple of seconds later it feels as though the brakes come on because the truck slow down so drastically and when I give it a little gas it slams into gear. It feels as like there is a "gap" where nothing is engaged before it slams back in. This is a rebuilt tranny with less than 7K miles on it. I took it back once and they said it was the motor mounts. I had those replaced and still the same problem. I replaced the spark plugs 6K miles ago and the COPs 3K ago. There is 170K on the truck. I only drive about 8K miles a year.
View 2 RepliesFord F-150 - 1997-2003 :: Truck Seems To Surge Or Hesitate At Pretty Much All Speeds
I have a 97 F150 4.2l auto 4x4. The truck seems to surge or hesitate at pretty much all speeds. I have had the truck on fords so-called super "sbds" computer and they found nothing. I am taking it tuesday to have the o'2 sensors and CAT. Convertors checked at a local parts/service store. Also found out today that my speedometer is 5 mph to slow (doing 65 but speedo only registers 60).
View 14 RepliesFord F-150 - 1997-2003 :: Bad Miss Under Acceleration Below 2500 RPM
I have a 97 f150 with 4.2 4x4 auto. I have a bad miss under acceleration. if i ease on the gas no problems. stomp it and it chugs and pops back thru airbox til it gets to 2500 rpm then clears up. If I shift it manually and keep rpms up its fine till it gets below 2500. I have replaced spark plugs, plug wires, fuel filter, upper and lower intake gaskets, cleaned injectors, new air filter and cleaned o2 and mas sensors. Had vacuum system checked and was told all good.
View 12 RepliesFord F-150 - 1997-2003 :: 2002 - Rough Idle - Hesitate While Accelerating - Replacing Coils And Plugs?
I have a 2002 f150 with the 5.4. Its got a rough idle and a bit hesitant on acceleration. Im wanting to replace the coils and plugs but what brand of coils should I use?
View 3 RepliesFord F-150 - 1997-2003 :: 2001 - Miss At Low RPM - Light Throttle
My 01 Super Crew 5.4l is missing at light throttle. Cruise control on flat hwy, no miss, slight incline, starts missing. Put my foot into it and either it stops missing or it covers it up where I don't notice it. No codes set at this point. It's got about 135k on it and for all I know it may have had the original plugs in it so I figured I'd change them. Changed the plugs, still misses. Shortly a code set, something about the EGR sensor (it's got another name but I forget what it is at 1:30am). I found I had broken a hose while changing plugs, fixed it, no more code, still misses.
When I sent my GF up to get the non-existent codes checked the parts guy sold her some Lucas fuel system cleaner. I'm figuring a COP going out but the cleaner pretty much completely fixed the miss, till that tank of gas was gone. Few tanks later and it's back again as bad as ever. I bought some seafoam as I've had good luck with that in the past. It almost completely fixes the miss but I get a rare 'bump'. What do I need to look at next? Can it be the fuel filter? I'd think no because I'd figure it'd be even worse at greater throttle opening. Injector? How do I check them?
Ford F-150 - 1997-2003 :: Rough Idle And A Miss While Driving
I recently inherited a 99 Expedition 5.4 with 90k miles. I'm trying to fix it up so I can sell it. Like the title states, the truck runs rough but there's no check engine light on. I did some research and ended up replacing the PCV elbow and that made it run better for a while but now it's back like it was. It won't die, just a really rough idle and a miss while driving. I imagine it's probably a (or a few) coil pack(s), but I have no way of knowing which one(s) to replace. I would think that would illuminate a CEL though. I'm also having problems with the AC. Upon inspection, I found that the compressor clutch assembly was completely gone from the front of the compressor. I replaced the whole clutch assembly, then voided the system of Freon and refilled it to spec, still no cold air. The compressor clicks on and off like it's low on Freon but it can't be. I'd just sell it as is but in south Louisiana a working AC is a huge selling point!
View 1 RepliesFord F-150 - 1997-2003 :: Miss At Idle When Warm Low End Power Slacking
Alright so I have an 03 5.4 with 144000 miles. once it warms up to temperature it has a miss and low end power is low and no fuel mileage gets 12 to 13 if I'm lucky. From idle to 3000 rpm its doggy get it over 3000 rpm it runs great. All new plugs and coil packs. What it could be. When the motor is cold it runs great has most its power.
View 3 RepliesFord F-150 - 1997-2003 :: Bad Miss / Exhaust Smells Like Fuel / CEL Blinking
I have a 97 f 150 with the 4.2 bad miss on # 6 changed plugs and wires still missing. Also have a bad tick and exhaust smells like fuel. Check engine light is blinking.
View 10 RepliesFord F-150 - 1997-2003 :: 1999 V6 - Engine Will Miss In A Pull And Die Sometimes But Start Back
Engine will start and run but will miss in a pull and die sometimes but will start back, we hooked it to a scanner and it said (intake wiring) it wasn't a dealer hook up just a gas station garage, we have already done plugs and wires.
View 2 RepliesFord F-150 - 1997-2003 :: 1998 F250 - Transmission Shudder Or Engine Miss Below 10MPH?
I have a new to me 98 F250LD with the 4.6/4R70W. I have maintained this truck fro my FIL as best as I could get him to spend (neglected). Filter and fluid replace with Mercon VI last year due to 2-3 shift slip.
He gave me the truck after it would not climb a hill, just hit stall speed and would not move up a steep hill, as I understand it. I put Seafoam trans tune in hoping it would free up sticky solenoids or valves in the VB.
I finally got it registered in my name and drove it to work and back today. After about 25 miles highway driving it shudders pretty bad trying to climb a hill at low speed.
It seems to me that at this low speed, torque converter lockup should not even be a possibility. I do not have COP, but rather a single coil pack. I replaced the wires and plugs for Dad a few years ago, but some shady shop later told him that I didn't replace the left rear (to make an upsale I suppose). Not sure what they may have done in there.
I have scanned with my ELM 327 and Droid using Torque Pro, and the only Fault is EGR flow.
Ford F-150 - 1997-2003 :: Slight Miss / Rough Idle - Hesitation Or Stumble On Acceleration
2003 F150 5.4 72852 miles
I have a Rough Idle & sometimes a hesitation or stumble on acceleration. I cleaned the MAF & IAC motor & Air & Fuel Filters are new. I got a 20890 scanner & ran test 6 53 as suggested in many posts by BlueGrass. Here are My results & what They Convert to.
1 00F5 .3675
2 0051 .1215
3 0000
4 0000
5 00A3 .2445
6 0000
7 0000
8 0000
I'm guessing the cop's are ok & probably need plugs? I was hoping to just swap a coil. Too cold to do plugs & truck won't fit in my garage.
Ford F-150 - 1997-2003 :: Starts Perfect After A Cold Soak But Then Miss / Sputter And Loss Of Power
1997 F150 4X4 4.6 engine with 285,000 miles
Truck was running perfect down the road, then suddenly it lost power and started missing at all RPM ranges. So i keep driving another 6 miles and then POOF the miss is gone and truck runs perfect. Couple hours later i hop back in it and its running good and then suddenly it starts missing and loosing power again except this time it never started running good again. Never did throw a CEL.
I hooked up my SCT Tuner (for my F250) to check for codes and came up with P0171 which indicated one of the banks was running lean, but no missfire codes. Did a search on here and learned the common problems(vacum leak) of that code.
Found the vacum leak at the PVC elbow, so i replaced both ends of the plastic tube.
Pulled the throttle body elbow and cleaned out the clogged up EGR ports.
Put a new air filter in and took the MAF out and cleaned it with MAF cleaner.
Put it back together and it idled way better but still ran like crap with the bad miss/sputter. Ran it down the road a few miles and came back thinking of the catalytic converter, i crawled underneath and it was glowing red. It does run and feel like the converter is stopped up but if i have a dead miss and dumping fuel wouldnt that make it glow red to or no? Still no CEL and now no codes.
Also i held the engine at about 1000 rpms where i could here the miss good and unplugged the fuel injectors one at a time to see if that made a difference. Each one i unplugged made it miss worse, so wouldnt that tell me that all 8 cylinders are firing?
And i changed the spark plugs (motorcraft) 250 miles ago.
So it still cranks and runs smooth after a cold soak overnight and then after a mile of driving or less it starts the dead miss/sputter and loss of power.
Ford 7.3L Power Stroke (1999-2003) :: 2000 - Bad Miss Or Stutter / Knock At High RPM And Deceleration
2000 F250 7.3L ZF 6spd 4x4 regular cab long bed 253k
DP F6 chip, 4" exhaust, WW2, EBV delete
I run 5w40 Rotella Synthetic. Oil was changed about 1,000 miles ago. I also added a quart of Hot Shot stiction eliminator. I use Power Service and Stanadyne lubricity in every tank. Fuel filter is new.(motorcraft)
For a month or so its been acting weird. I get a stumble/miss/stutter, at random, but mostly under hard acceleration and high rpm (specifically approx 2500-2800rpm). It will also do it on decel when I lift after accellerating . Recently, I noticed it is also idling roughly. The engine is shaking and it feels like a miss. When it does its "thing" it sounds like a single "knock". Occassionally, it sort of sounds like an injector "buzzing". I've been using the "stock" tune for the last few weeks, to minimize any chance of engine damage, as I have to drive it. Turning up the chip makes the problems more noticeable and happen at a lower rpm. The truck has plenty of power, and pulls hard, except for the "stutter". If I hold my foot in it to "push through" the initial stumble at 2500 or so, it will keep going a few hundred more rpm, and then really start bucking.
There are no meaningful codes. I DO have:
EBV related soft codes - makes sense since its deleted.
Overboost related codes- from turning the chip up - won't happen in stock setting
A soft code for the back pressure SENSOR. I have a new one and will be cleaning the tube when I get a chance. I unplugged the sensor and it made no difference in the miss issue.
I have recently done the following in pursuit of a solution to all this:
New IPR (autozone) valve and pigtail
New ICP (motorcraft) and pigtail ( sensor had oil in it)
New CMP and pigtail. (2 actually. First a standard pc139 for the obs, and currently a Napa echlin correct for '00) No change. Although it initially had the dreaded Ford small head light grey sensor and failed cct for #3 & 8. After the cps change, it passed cct.
Accellerator Pedal Position Sensor. It would not read any higher then 3.95v at wot, and only 0.50v at idle, so I installed a new one. After adjusting it a little, I have 0.76v at idle, and 4.02 at wot. Didn't affect the stumble issue, but it seemed to greatly improve/eliminate my parking lot speed "bucking".
I just did the UVCH's. The passenger side was pretty much unplugged. But they all looked good. No burnt, melted,or chafed wires anywhere. I probably could have just plugged it back in, but I changed both sides with new Motorcraft parts anyway. I did the gaskets and the uvch, but not the engine side harness/pigtail, as they looked ok. I also did the 0.50 mod as a preventative measure. After seeing the unplugged harness, I really thought this would be the end of the problem, but its not. Very frustrated.
As a side note, I was surprised to see that I have 8 AD injectors, and not an AE in cyl 8.
I have an old outdated snapon scanner. Its only good up to '99, but I am able to scan my 2000 as a '99. I think I'm missing some pids though.
I can do cct and buzz test, but no PERDEL readings.
As far as ICP, it idles at about 450psi, at approx 12% IPR dc. On a brief 2nd gear wot run, it will hit (and hold as long as I have road to stay in it) a little over 2900psi, at 41-42% IPR duty cycle. I did notice, during these near instantaneous stumble events, ICP would flutter on the scanner about 75-100psi. Its almost too quick to even see it.
Ford 7.3L Power Stroke (1999-2003) :: 2000 - Occasional Miss At Highway Speeds / Bucking And Jerking During Even Gentle Acceleration
165k miles 4x4 6 speed, bone stock unmolested
Slowly progressing problem over 6 months. Occasional miss at highway speeds uphill has progressed to bucking and jerking during even gentle acceleration attempts.
I hadn't got my cam sensor recall done but no change after that procedure completed yesterday. Oil recently changed as well.
I have a torque pro but it never finds any fault codes even though 'service engine' light comes on sporadically. I'm not sure I'm operating it properly but it at least reads rpm when its running.
I'm contemplating the hutch mod but I'd like to have an official diagnosis beforehand if its possible in my case.