Dodge - Durango :: When Hit The Gas It Feels Like Driving Over Rumble Strips
I have a 02 durango. Yesterday once i was accelerating over 30 it started feeling like i was driving over rumble strips a little. It felt like it was towards the back. I drove 15 miles to the store and back. On the way home it died down and went away. Today I started driving to town and it is doing it at all speeds. The vibration doesn't seem to change with speed but is much more intense. Only happens when I give it gas. I have searched many forums and not sure where to start? I've read everything from torque converter to solonoids to u-joints, axle bearings, engine problems, or a bad differential.
View 5 RepliesDodge - Caravan :: 2007 - Intermittent Vibration Which Feels Similar To Driving Over Rumble Bars
Our 2007 Grand Caravan with a 3.3 Liter Engine has intermittent vibration which feels similar to driving over rumble bars. It usually occurs between 30-50 mph but sometimes at 70-80 mph as well. Have had the suspension checked and had outer tie rod end replaced. Also had sway bar bushings replaced and front end aligned. We then brought it to transmission shop and had a transmission diagnostic performed. They found no faults with the transmission and thought the engine needed a tune-up which we did with no success. At a recent oil change, we asked for them to test drive it and check again for any suspension problems. They did not notice any vibration during the test drive and found no problems with the suspension.
View 4 RepliesFord - Focus :: Vibration Like Driving Over The Intense Short Rumble Strips
Problem: Vibration together with a noise that sounds abrasive and destructive. Mechanics have failed me.
It feels like driving over the intense short rumble strips that are meant to tell you when a wheel is outside the traffic lane. I feel and hear it in any gear, whether I am moving or not, but hardly at all in Park or Neutral, and hardly at all when cruising at high speeds. It is worst on the first drive of the day - much less on subsequent drives, even if the engine has been allowed to cool fully.
History: When this began, less than 600 miles ago, I had the transmission checked, where I had warranty coverage.
Found: No transmission trouble but a broken engine mount.
I had the engine mount replaced (and two gaskets replaced because they had started to leak), together with Virginia's mandated annual inspection - passed.
Vibration lessened but continued and started to worsen. Within 3 days the engine stalled in traffic and THE NEXT DAY the "check engine" light came on. I went back to the same place. The ignition coil and spark plugs were replaced. Power returned, and no stalling or warning light, but the vibration persisted.
One mechanic baffled: "What do you expect with 101K mileage and 16 valves?" - But this came up too fast to be ordinary wear and tear. What should I do?
2.0L Zetec E engine.
Ford Ranger / B-Series :: 1998 - Randomly Feels Like Hit Rumble Strips
I have a '98 Ranger 4.0L SuperCab 4x4 Automatic
The other day i was driving, around 40 MPH and suddenly the truck felt like I hit rumble strips on the highway, I hit the brakes and when the truck got down to about 10-15 MPH, it went away. It didn't feel like an out of balance tire or anything like that. It felt exactly like I hit rumble strips. It was a strong, high frequency vibration. I then continued on my way, and it was fine for a little while, still doing 40 mph, then suddenly out of nowhere the same vibration came back. Once again, I slowed back down, it went away and stayed gone even when I sped back up.
Both front hub bearings are less than a year old, and a quick check of the driveshaft seemed to indicate the u-joints are still tight. Front diff/driveshaft turns freely and smoothly and the front hubs are not locked.
'm going to try and jack the truck up and check everything thoroughly, but I'm really at a loss here, as I've never experienced anything like this before in any vehicle. Some reading suggests that it might be transmission related to the 5R55, but I'm really unsure.
Infiniti - G35 :: Random Vibration When Driving Over A Smaller Version Of Rumble Strips On Side Of Road
My 2005 Infiniti G35 has 144,000 miles, two new rear tires and two good front tires. Sometimes, and I cannot nail down or reproduce-on-demand this situation, my car will suddenly begin to vibrate as if I'm driving over a smaller version of those rumble strips on the side of the road. The vibration continues when I take my foot off the accelerator, and will continue at a slower rate as I decelerate until I stop. Often it seems that when I come to a dead stop and accelerate again, the vibration stops, but other times it will continue as I accelerate.
But what's really odd is other times I'll just be cruising along and the vibration will begin, keep vibrating for a few miles, then peter out and disappear. I haven't totally nailed down whether or not braking affects it, but if pressed I would say that I would use the brakes at least once before it disappears. Also, it only seems to begin once I hit 50-60 mph, but again, it doesn't happen every time I go this speed. Other times this car drives incredible and makes the road feel as smooth as glass.
I haven't taken it to the shop because I'm sure they won't be able to reproduce it.
Ford F-150 (2009-2014) :: 2010 - Seems Like Driving Over Rumble Strips - Cylinder Misfire?
My 2010 F150 randomly feels like I'm driving over the rumble strips as well as a small jerk like there is a cylinder misfire. If keep it at constant speed it still happens, but under cruise control it stops. Even when load increases like going up a hill.
View 14 RepliesFord F-150 (2009-2014) :: 2013 - Shudder At Low Speeds Like Driving Over Rumble Strips
I hooked up the boat and went out for a tow. I ended up getting a pretty good vibration and thought maybe it was time for balancing the trailer tires. As it turns out I needed two new tires as they were at the wear bars (cheap crappy bias ply tires) so I ended up buying 4 trailer tire radials and had them balanced.
As it turns out I have what I guess is a shudder at slow speeds and also can feel it at other speeds as well. A way to explain it is that it sort of feels like you are driving over the rumble strips on the side of the road but really small ones.
Ford - Explorer :: Torque Converter Replaced - Sound Like Driving Over Rumble Strips
Had the torque converter replaced twice on my 2007 Explorer Limited last December. Ford dealer did it once and then there were still issues so they had to replace it again. All seemed fishy to me.
Now a new issue that sounds like driving over rumble strips. Torque converter?
Dodge - Stratus - Wheels :: Feels Like Driving Over Warning Strips In The Road
2001 Dodge Stratus R/T, 5 speed manual - under load, it feels like I'm driving over warning strips in the road, and stops when I coast. The CVJ's feel and look OK. So do the wheel bearings. Could it be something in the final drive? It happens in all the gears.
View 1 RepliesFord F-150 - 1997-2003 :: Slight Rumble When Driving - CEL Came On - Code P0306
I have a 99 f150 5.4 and i am pretty sure I have a cop issue. I have changed a few over the past few years and this one is acting about the same. The other day i felt a slight stumble but it went right away and drove fine. Well after heavy rain all night i went to take the kids to school and it was stumbling and acting like it was not firing on all cylinders. CEL came on and got the code read at the auto part store. Well driving it home it just cleared and drove fine. So i checked the #6 plug and changed the boot on the coil but all the same symptoms came back. It is the original coil so i am figuring that it is bad.
View 3 RepliesFord 6.0L Power Stroke Diesel :: Truck Felt Like Rolling Across Rumble Strips At About 1500 Rpm And 30 Mph
Very weird thing happened on the way home from work. When I left work (not to full temp) at about 1500 rpm and 30 mph (had to be at 30mph--seemed to be the key) the whole truck felt like it was rolling across rumple strips (the ones one the shoulder of the road) all vitals were normal and it was gone once on the interstate and up to temp (I did gon on it to blow out anything that may have needed to be) it felt more like drive line but honestly can't say. 2006 F350 4X4 ....
View 7 RepliesFord F-150 (2009-2014) :: Shudder Like Riding Over Tiny Rumble Strips Or Pebbles And At All Speeds
I've looked at all the shudder issues thru the forums and mine seems a little different. Mine feels like I'm riding over tiny rumble strips or like pebbles and at all speeds. I just got new tires and a front end alignment. mine seems to do a little bit of that shudder thing but all the time. I bought it used from a honda dealer with 48k on it. I have to take it to them for the warranty they gave me. Curious how that's going to work out. 2009 5.4 3.55 rear and 157" wb. 4x4.
View 3 RepliesChevrolet - 1500 :: Truck Vibrating Like It Is Going On Rumble Strips Only Over 40MPH
My truck just recently started to vibrate like it is going over rumble strips. It only happens over 40MPH and sporadically. It seems to happen when I'm just giving enough gas to maintain speed. Once it starts if I let off the gas or give it more gas it goes away. It reoccurs anywhere from 20 seconds up to a few minutes. I'm afraid my tire is going to fly off or my drive shaft is going to drop. There is no unusual noises or thuds if I go on and off the gas and the universal joints seem tight, and there is no vibrations from on steering wheel.
View 10 RepliesFord Ranger / B-Series :: 1997 - Vibration Feels Like Wheel Hop
I'm having a bit of an issue with my 97 ranger 4.0 auto 2wd. I have an vibration which from a stop up about 10 mph feels like wheel hop not bad but you can definitely feel it it and over 50 mph the whole truck starts to shake again not bad but you know its there. the truck sat last summer it was my dd till a bought a new car and now vw is buying it back ill be driving the ranger in the mean time. I have been trying figure it out for a few months but no luck i have put new tires , front rotors and rear drums , drive shaft support bearing ( 2 pc shaft) new u-joints and a used boneyard shaft with new u-joints as well, checked the tail shaft bushing which had about .008" of play.
Pulled the drums Off today and checked the axle bearing for play only .004" of play pulled the diff cover and checked for carrier play as well as pinion play but can't find anything. I'm at a loss here and looking for other things to check ... Don't know if its possible that something in the transmission is loose it was rebuilt about 75k miles ago I was going to stop and talk to the trans shop to see what he thought (its a 5r55e ) ....
Subaru - Forester :: 2009 - Transmission Vibrations Going Over Rumble Strips When Upshifts From 3rd To 4th Gear
I have a 09 Subaru Forester with 66k miles that vibrates like it is going over rumble strips when it up shifts from 3rd to 4th gear. It occurs under normal (not brisk) acceleration. I had the trans fluid changed at both the 30k and 60k services. I have owned this since new. It began before the 60k service. Also, sometimes the tach will increase revs during this as well. I don't know if this next thing is related but when I once need to merge quickly into interstate traffic I gave it a good amount of throttle and the tach revs increased but the trans did not follow with an immediate down shift.
View 4 RepliesFord F-150 - 1997-2003 :: 2000 5.4L - Intermittent Engine Knocking Underneath
The knocking started very suddenly 2 days ago - but not after any unusual events, other work etc. Truck has 145 K, and otherwise starts & runs perfectly. Doesn't use oil.
I heard it from in the cab, windows closed. At first, thought it may be a rod bearing - but if so, not terribly loud. Didn't drive it any more after getting home. But starting it in the drive, the knocking was audible.
Then I discovered it * completely disappeared * several times, after shutting off engine, then restart a few seconds later. When that happens, absolutely no knocking at idle or reeving it up a bit. But it may return on the next 1 or 2 restarts, then disappear again.
Since the knocking * completely stopped * on some restarts, does that rule out a bad rod or main bearing?
I haven't seen oil gauge pressure fluctuation, whether it's knocking or not. The gauge is where it's always been - well above 1/2 way. But, the gauge also doesn't move when I rev it to around 2000 RPM (? may be normal not to move, after engine's already running?). When the knocking is happening, increasing RPMs also increases the knocking frequency.
Can't hear the knocking from top side of engine w/ hood open - even using rubber hose to my ear & moving it around. But (when) it knocks, can easily hear it inside the cab or under the truck.
From underneath, knocking is more in the center of truck, near the back of block / oil pan or tranny bell housing. I can't isolate the noise as more on one side of the block than the other.
Could the oil pump itself be making a knocking noise? The knocking is "similar to" a rod knocking, but doesn't seem quite as "hammer on metal" metallic.
There are no DTCs showing on my scanner. Only odd thing was, for "O2 Monitor Test," it showed "vehicle did not return data for any O2 monitor test." Though under the scanner "I/M Monitors," it shows O2 Sens Mon. "OK," and O2 Sens Htr "OK."
Ford F-150 - 1997-2003 :: 2000 - Strong Vibration In Steering Wheel And Dash
Purchased 2000 F150 (224000 miles) about a year go cheap for knock around truck. Only gets driven about twice week (20 miles most). Has been running great until recently. Got in the other day went about a mile and notice really strong vibration in steering wheel and dash. First thought about something to do with alignment etc. After a little experimentation realized it was the motor. When you get to around 40 mph and try to hold the speed constant it starts shaking (I believe the motor is missing). If you mash the gas and accelerate it stops. As soon as you try to hold constant speed again it starts again. I can run it up to say 45 and let off the gas and the shaking stops. Once it was driven like this for about 5 miles or so, when I come to stop sign it idles rough. If it is put in neutral runs smoother. Could the fuel filter be clogging up? I did try some additive to see if it would clean it out, no luck. Now the check engine soon lite came on. Fuel Filter, Plugs?
View 5 RepliesFord Brakes/Suspension :: 1997 - Rear Drums Sticking Feels Like Driving With Brake On?
I have A 97 F-150 4X4 with rear drums. I noticed the brakes felt like they weren't releasing right away after i let of the brake pedal. i took drums off and noticed on the left rear the front shoe moved normal but the rear shoe didn't move at all. on the right side front shoe moves normal rear shoe very very slow, and i could see rear shoe was worn way more than front. So I replaced on both rear the shoes, all the hardware, springs, wheel cylinders and brake line from cylinders to the proportioning valve.bleed the brakes, and adjusted the drag on the drums. Now i drive it, test it out, feels like the same issue is going on. feels like im driving with the brake on, and right rear gets really hot. Did i miss something? not do something right?
View 4 RepliesFord F-150 - 1997-2003 :: 2000 XL V6 4WD Went Out While Driving At 65 MPH
I have a 2000 F-150 XL with a 4.2 V-6, a 5 speed manual transmission and manual shift on the fly transfer case. The 4WD went out over a year ago. When it went out, I was driving at 65 MPH and heard what sounded like rapid relay chatter for several seconds (10 to 15 seconds) and it stopped. The sound seemed like it was coming from the dashboard area where the GEM is located, but may have been from the solenoids mounted on the engine compartment firewall. Actually could have been from both. When the 4WD tried to engage while driving at 65 MPH, the dash lights were flashing on and off and it sounded like the front differential was trying to engage. Of course I slowed down while this occurred to avoid damaging the truck should it succeeded to engage the front differential.
I have a Haynes manual but the wiring diagrams are some what ambiguous as my truck is not as common as those having ESOF. Even researching online I am not certain if the info pertains to my truck. The only diagram I found to be accurate is the vacuum control diagram. I believe I have either a wiring problem or the GEM is bad. When troubleshooting I like to isolate at the middle points to quickly eliminate one side or another when looking at a diagram/schematic.
Ford had a well-noted problem with the two solenoids that control the 4WD actuator and are mounted on the engine compartment firewall. So I started here, as this is a good halfway point and high failure area.Well, the solenoid power connectors had 12 volts on both connector pins (if I remember correctly as it was a year ago when I did some troubleshooting)regardless of transfer case shift position (2wd, 4wd high or low). I was able to manipulate the solenoids and verified they were operating, as I could feel and here the solenoids click when grounding the control side of the pin on each solenoid. I did check fuse 23 prior to checking the solenoids. Since 12 volts was present at the solenoids, it indicated power was getting to them.
So another common problem is the transfer case 4WDsensor. I removed, cleaned, and verified operation of the sensor. Reinstalled and check sensor state with transfer case in all 3 positions and it was working correctly. Also I have no 4WD indication on the dashboard when 4WD high or low is selected. Fuse 6 is good.
My main issue is not having confidence with the wiring diagrams I have found online. I am not sure if my truck has a MSOF relayor the transfer case 4WD sensor signal goes directly to the GEM.
I need to check:
1. Wiring from transfer case 4WD sensor to either GEM or MSOF relay, if there is a relay, will check it along with wiring to GEM,but don't believe it exists for my truck. (I need the wiring diagram to do this)
2. If the transfer case 4WD sensor output is getting to the GEM module, I would think the GEM module is bad. If possible, I would like to check the GEM module outputs to the solenoids, but since the GEM is buried behind the fuse panel, it probably is not feasible.
I plan to call the Ford service department in my area to determine what GEM I have and will buy a GEM online. Replacing the GEM does not look fun, so I have avoided it but wanted to be sure it was the problem.
So I want to know if I am tracking correctly and if there is anything else I should check, and would like the correct wiring diagram as indicated in item 1.