Ford Brakes/Suspension :: Rear Brake Sticking / Hot Smell
I was fueling up my 06 F-250 yesterday and smelled hot brakes. I checked and found the right rear was really hot. After it cooled down I was able to drive on home and it was not too hot when I got here. I was towing a trailer with my tractor on it so I had a pretty good load. It was over 6 miles to my house with stop and go traffic and no hang up. What should I do to keep this from happening again? I don't drive this truck much but when I need it, I need it to be dependable. It has 99k on the clock and is a gas job.
View 1 RepliesFord F-150 - 1997-2003 :: 1998 - Converting Rear Drums To Disk Brakes
I have a 1998 f150 4x4 4.6 triton V8 regular cab, I would like to ditch the rear drum brakes in favor of disk brakes. is this an easy bolt on project? I do know that 2003 f150's had rear disk brakes and was wondering if i bought those parts if the procedure would be fairly easy. I know i would have to take a check valve out of the master cylinder to gain pressure to the rear.
View 8 RepliesFord Brakes/Suspension :: 1984 F250 - Brake Sticking When Going Downhill Just Coasting
I got my grandpa's 84 ford f250 its been sitting in the barn for awhile but i drove it over to my house yesterday and it drove fine but you did have to push on the brake quite a bit but not to bad but today after school i took it for a drive around the block and i noticed that when i was going down hill just coasting i was slowing down a lot and my foot was not on the brake but when i got home my breaks were smoking pretty good but tomorrow i was going to take the front breaks off (its only the front two disk breaks doing this) and clean all the rust off them and put a little oil on the piston on the caliper that pushes on the break pads...
View 1 RepliesFord Brakes/Suspension :: 1997 F350 - Driver Side Rear Brake Hot
Last weekend I did a rear brake job on my 1997 F350 4wd diesel. I replaced the shoes, replaced all the hardware, replaced the cylinders and had the drums turned. I have driven the truck all week and everything has been fine. Tonight while out of town I set the parking brake to see if it was any better since the rebuild, and it was. Shortly after releasing the parking brake I drove about an hour to get home. When I arrived home by driver side rear brake, wheel, etc. was very hot. I threw water on it and it turned to steam instantly.
I suspect that setting my parking braked hard like I did (like you're suppose to) somehow caused it to drag. What is causing this and what needs to be done so that it doesn't happen again?
After reading some other posts I went out and checked my parking brake cable and found that it is not bound up that I can tell. Perhaps it did not completely release although it seems to release just like the other side. I checked it from front to equalizing bar and it is in great shape. The plastic coating is still on the wire and there isn't any corrosion the entire length. The only thing I did differently on this trip vs the one I made two days ago was try out the parking brake before I left. The last trip I could barely feel any heat on the rear wheels when I got home, this time the driver side was scorching hot.
Ford Brakes/Suspension :: 1997 F250 - Passenger Side Rear Drum Brake Was Full Of Oil
Recently purchased my first Ford truck, a 97 F250 w/7.3L diesel. I discovered the passenger rear drum brake was full of oil. Cleaned it up and put it back together to do some research.
I see how the hub comes off and there are two bearings in it an an oil seal. The bearings are lubed in wheel bearing grease. Does differential oil circulate through the bearings too?
It doesn't look like a difficult job. Do the seals go bad often or could this be due to a clogged differential vent? Truck has only 100k miles. Any gotchas I should be aware of?
Ford Brakes/Suspension :: 1997 F150 - Converting Drum Brakes To Rear Disc Brakes?
I have a 1997 F150, 4X4. My mechanic says its time for new brakes and was curious if it would be worth possibly converting from drum brakes to disc brakes??
My mechanic has quoted me $300 to do the rear brakes, would it be worth the extra money to convert??? I really don't care for drum brakes. I have done a search on the internet and every time it brings up the issue with the parking brake.
Ford Brakes/Suspension :: 2006 F250 - Rattling After Doing Brakes / Emergency Brake And Rear Wheel Bearings
Before I get started... My truck is a 2006 F-250 Super Duty XLT 6-speed 4x4 with a Limited Slip.
I just got finished with a big job on my truck. New pads all the way around, turned rotors, new emergency brake shoes, hardware, and backing plate as well as replaced the rear wheel bearings both inner and outer as well as the axle o-ring and inner seal. Also, took off the rear pumpkin cover painted it and put fresh fluid in, went with Mobil 1 75W140 LS.
Took it for a drive and the brakes work great. Followed the directions for breaking in the emergency brake which worked fine.
Now the problem is I'm getting rattling from possibly all of the wheels. Definitely from the front driver and at least one of the rear wheels. It was so dark I didn't get a chance to look at it I just pulled it back in driveway.
I'll start looking at things tomorrow but, any common mistakes or things I should check first?
Ford F-150 - 1997-2003 :: Hot Drums And Brakes Dragging On Takeoff
My husband bought a 1997 Ford F150 and the seller said he changed the brake lines, but the back brakes have dragged on takeoff since he bought it. Just put new shoes on it and it's still doing the same thing, but now the drums are getting hot. Is it possible that the seller got the brake line backwards and that might make the back brakes drag?
View 2 RepliesFord Brakes/Suspension :: 2000 2WD - Front Brake Scraping While Driving
2000 Explorer 2WD. I had tons of front end issues that I have been working through. So far I have done upper control arms, upper and lower ball joints, tie rod ends, got an alignment. The steering/suspension system is in good shape now.
Now the only thing left is a scraping/grinding sound coming from the driver's side brakes. I mostly hear it at low speeds (taking off from lights, etc).
When I was doing all of the other work, I observed that the rotor is in great shape, brake pads look great. I am wondering if it is a caliper issue, maybe the caliper isn't releasing enough or something. What to check?
Ford Brakes/Suspension :: 1997 F150 - Brake Pedal Keeps Fading
I recently purchased a mutt of truck, a 97' F150 heritage w/5.4 Triton motor, 1/2 ton 2WD short bed.
Having a brake issue, the pedal keeps fading. I noticed it first while sitting in traffic on a down hill grade. I am holding the pedal and notice it starts to creep down slowly, I pump it up and it firms up then starts collapsing again. So general logic says hydraulics are loosing pressure right?....No leaks anywhere, so it must MC tight?
I have replaced the master cylinder, brake booster, and both rear wheel cylinders. Long story short they all needed it, truck has 265K+ on the body with 95K on the motor. The only thing I did not do by standard is bleed the MC on the bench, I installed and long bled starting with the right rear working my from longest distance to shortest (wheel speaking). So when bleeding I did of course get air coming out because of the new parts but I still have the same fade issue.
I am confident there is no air in the lines, I have bleed a quart of brake fluid through just to be sure. I have read a lot about proportioning valves and ABS stuff.
I will try and get some vehicle specific photos and attach have hit a road block with this. I am leaning towards the ABS valve thingy mounted on the drivers fender that has four lines attached (2 in and 2 out). Other than that it comes down to hard lines which have no leaks.
Ford Brakes/Suspension :: 2000 Excursion - Rear Brake Line Leak
Rear steel brake line ruptured the other day (was pretty rusty). Despite being an idiot in regards to automotive repair (among many other things), I decided to give it a shot. I was able to get the damaged section off, went to Autozone with the broken piece, they matched it up, were nice enough to cut it and put on one larger fitting (because the two were different sizes) and flare it for me.
I was able to get the one side (at the T fitting) on OK. That was the "new" side, the one they flared at Autozone. Looks good. No leaks.
The stock side, at the passenger side caliper, leaks like crazy. Not out the threads, but out the hole through which the line passes. Know what I mean?
I'm having a hard time figuring out what's happening, because I'm not sure how this thing works. Does the line fit flush to something inside the connection at the caliper? Is it a bad flare?
It did not go in easy, but the new one was just as much trouble as the fitting that came out (stock?), so it must be right.
Ford Brakes/Suspension :: 2001 F150 - Rear Brake Lights Not Working
I have a 2001 F150. Front brakes replaced a few months ago. Last night, I realized my rear brake lights weren't working. I'm not sure how long they've been out or if it's related to the bigger problem.
While testing the brake lights by pressing the brake pedal, the pedal seemed to give out and sink lower. While driving the brakes worked but only when I pushed the pedal all the way in. Eventually the ABS light came on and stayed on.
Camry :: Gen 5.5 Rear Brake Drums And Parking Brake - Lubrication?
Gen 5.5 (2006 LE (57K miles), Rear brake drums and parking brake.
I want to get my parking brake lubricated and rear drums cleaned and adjusted. Is is difficult to lubricate the parking brake?
I plan on getting this done with a Mobile One oil change at a local garage.
Accent MC (2006-11) :: Rear Drums Clicking When Applying Brakes?
I am having a issue with my 07 accent. Had front rotors and pads replaced because they needed to be. Clicking continued. Had drums and shoes replaced last month. Clicking went away for a few weeks. Recently started back up just the other day. The clicking is only when applying the brake and it sounds like it is coming from the right rear drum. It doesn't interfere with stopping, but it s so annoying and brakes shouldn't make that kind of noise anyway.
View 7 RepliesHonda - Cr-v :: Rear Brakes Won't Stop Squeaking After New Drums And Shoes
I took my car in about three months ago when brake indicator started squeaking in the rear. Shop told me that the drums, shoes and wheel cylinders needed replacing. After spending a few hundred replacing all those parts, the squeaking began. It's a kind of rhythmic squeak that starts towards the end of braking. the rate varies with the speed of the car, so it definitely seems to be coming from the brakes. I took it in not long after. They said they only heard a clicking noise, and that was because the brakes were mis-adjusted. They re-adjusted it. I drove it home. The squeaking is still there. This also happens a lot more when it's heated up so maybe that's why they didn't hear it in the first place.
I take the car back. They said the drum has been warped. They replace the drums. I take it home. Still squeaking a few days later, and I feel the brake pedal pulsating now. I take it back in. They say the issue is from the front brake rotors being warped. I get these replaced elsewhere with ceramic pads. Squeaking is still there.
I take it back in to the original shop because I'm certain it's from the rear. They look at it again and say the drums are warped, again, and that they'd never seen anything like it. They turn the drums. (and receipt says there will be no more warranty on the rear drums... what?)
Unsurprisingly, squeaking did not stop, not even the day after. I took it to a different shop. They spent all day on it and drove it around with me and their final word is that the reason for the squeaking is cheap parts. They recommended I call the original shop and ask for factory parts and offer to pay the difference for the parts.
Ford Brakes/Suspension :: 1993 F150 - Rear Brake Locking After Master Cylinder Replacement
I replaced the master cylinder 2 months ago and now every now and then the rear lock up for a second. its only happened a couple of times. Pulled the wheels and everything is in place with nominal wear with clean drums and rotors. Am at a loss as to why this is happening.
View 1 RepliesFord Brakes/Suspension :: 2000 F250 - When Brake Applied Rear End Starts Jumping And Bucking?
I have a 2000 F250 PSD. When applying the brakes, the rear end starts jumping and bucking. The effect is exaggerated when pulling a trailer and applying the truck brakes to stop. The problem does not occur when manually applying the trailer brakes. It was suggested to me that this problem is caused by a hydro boost leak.
View 3 RepliesPrius C :: Rear Brake Drums Are Rusty
My c is about 5 12 months old now, and the rear brake drums are already covered in rust.
View 9 RepliesFord Brakes/Suspension :: 1997 - Howling Noise / Rear Tires Started Locking Up When Turned
I've got a 1997 Ford Expedition 5.4 with 200,000. So my rear differential leaks a few drops of fluid every time I drive it, looks like it's coming from the pinion seal. I've just been filling it topping it off with fluid.
Anyway, yesterday I got in it and started driving, I noticed a howling noise, and when I turned my rear tires started locking up. It was like that for about 5 miles until I got home, no matter which way you turned the tires would lock up.
I went under and topped off the differential with fluid again, and I pushed my parking brake in and released it. Got back in the truck and drove, and it was fine. What happened? I'm just worried it will happen again if I don't look more into it.