Ford - Explorer :: 2003 XLT - Code P0775 - Slipping Of Gears And Rough Shifting
From the other users it seems that almost all are having slipping of gears and rough shifting associated with this code. On mine I'm not getting any slipping or rough shifting...it actually still seems to be driving just fine. The OD light came on and will go away after shutting the truck off and back on...it will then not flash anymore for say a couple of months or so...this has been happening for the past few years every now and again and i never thought much of it. I just made a 2k mile trip and this happened again but this time it threw the p0775 code which is a first.. Is it possibly a very early sign of the sensors going bad.
View 3 RepliesTiguan :: Tinny Grind Or Rattle Sound When Shifting Gears
I have had my 2010 Tiguan SE for about a month now and I have noticed a sound when it shifts that sounds like a tinny grind or rattle. This happens mostly in "D" not "S" mode and at the lower RPMs. Is it normal?
I took it to my dealer and of course they said they heard nothing, but it doesn't seem like something a new car should sound like.
Ford Transmission :: Tow Haul Darts Flashing And Shifting Weird
On the road and my tow haul darts flashing and shifting weird. Codes are P0528,P0730,and P2703. About 900 miles from the house at the start of my trip.
View 2 RepliesElantra GD (2013+) :: Weird Movement When Shifting Into 3rd Gear
I recently bought my GL less than a week ago with under 10km on it. Its been great so far but I noticed a weird movement when shifting into 3rd gear (both up and downshifting). It started happening about 2 days into driving the car.
As I shift into third gear I feel a little kickback against the forward motion. It doesn't happen all the time and it doesn't seem to be dependent on the car speed or the speed of my actual shifting. Although it happens a lot more when I shift quickly into third.
I've been told that 3rd and 5th gears are the longest and I might just need to get something adjusted at the dealership.
This kickback doesn't happen on any other gear except third (MAYBE I felt it a little on 5th but I may have been searching for it after being told about 3rd and 5th gear being long).
Ford - Ranger - Clutches :: Difficulty In Shifting Gears On Manual?
Ford Ranger 20012.5L
Manual 4 Cylinder4x2
Drivetrain~150K Miles
The problem with the vehicle is that it won't shift into gear easily and smoothly. It started occurring just this last Friday or Saturday (2011-06-24 or 2011-06-25). I was driving around 35 MPH, slowed down to a stop at an intersection, and when I put it back into 1st Gear to begin driving, I had extreme difficulty shifting the gear.
I cut the ignition and started again, was able to put it into 1st Gear and made it home by coasting (getting into any of the other Gears was just as difficult, fortunately I was in the neighborhood). Following this, I tested it while parked the next day. Same issue. Then I tried double-clutching, which seemed to work out, but I only did it parked, since I didn't want to strand myself on a road (I'll take that risk when I go to a mechanic, though).
I've read this [URL] ...., I'm pretty sure it's the clutch (master/slave cylinder) and I'm also aware that it could be the transmission fluid requiring a change. I haven't changed the transmission fluid at the 60K & 120K interval per Ford's suggested maintenance schedule (I got it around 50K-60K from a dealership, so I'm not sure if they may have done it preemptively).
A couple other details. For the past year or so, I've been driving 100 Highway miles for 4-5 days a week, for work (50 to work, 50 back home).
Are my assumptions right, or is it possible that my whole Transmission is getting ready to go? Are there any other details I should provide?
Ford Transmission :: 1991 - Delayed And Hard Shifting Between Gears?
I have a 1991 bronco with a 351w and the e4od trans.. The transmission is shifting late and hard and sometimes when i let off of the gas to slow down it shifts between gears up and down by itself... The only lights on the dash that are on is the Rear Anti-lock brake light and the speedometer is not working either.. Where to start the trouble shooting to fix it?
View 3 RepliesFord - Aviator :: 2003 - Slight Stutter In Auto Shifting Between Gears
My 2003 Aviator kind of stutters when in auto between gears. Most prevalent from 3 to D when driving regular. If I shift manually and tach it to 4k there is no stutter/vibration. My engine light is on and pretty sure the catalytic converter need to be changed. All new NKG plugs and associated coils. Throttle body clean, 91+ fuel only. Could this me a tranny starting to fail or computer/senor related? No other codes than the bank-2 O2 sensor....
View 2 RepliesFord F-150 (2009-2014) :: 2013 FX4 - Transmission Shudder When Shifting Gears
My son has a 2013 Fx4 crew cab 4X4 ecoboost with 8500 miles. He says in the morning for the first couple of miles while accelerating gradually the trucks shudders when shifting gears. After a few miles it goes away. Dealer says they can't do anything endless he can duplicate the condition. He went out of town for a few days and left me the truck so I'll drive it in the morning and see what it does.
View 3 RepliesFord - Explorer :: 2002 - No Acceleration On The Low End Gears
I have an 02 5r55w 2wd that I'm on the fence about right now and not sure if I should try and fix myself or pay $990 for a used one with unknown miles and 90 day warranty..
I bought it with 160-164k with no 2nd gear, OD flashing. Took it apart, replaced some bands, planetary, servo piston(end broke off-think OD.
After that, everything ran fine. NOw at 195k it's doing the I believe 2-3 high flare, rpm's go up to I think about 4k before shifting, sometimes more.
It has no acceleration on the low end gears, sounds like a dang 18 wheeler in it's low gears taking off, then I believe when int band kicks in, it picks up some torq and speed and shifts fine after 2-3 (not always does it-mostly when having to dump on the gas a bit).
Had issues with it jumping forward while on the brake. I've been in an 03 explorer with a good trans and could tell right away mine is pretty weak...
I was looking at the servo bore sleeve piston fix for $200. Maybe that and a shift kit, would that fix the issues I'm having right now? I haven't had any OD flashing or any check engine light codes. Haven't hooked it up to check codes, not sure if it logs if it doesn't flash check engine first.
I'm starting a business and will be pulling a 4x8 and need to get this one replaced or figured out.
Ford - Ranger :: Clutch Pedal Feels Normal But No Resistance When Shifting Gears
I have a 5-speed transmission pickup (’04 Ford Ranger EDGE SuperCab). Clutch pedal feels "normal", No resistance when shifting gears. Will go into gear with ease, except for 2nd gear (grinding noise), must push clutch to the floor and still grinds; but only 2nd gear. In 1st gear, my truck will slowly creep forward as if unable to engage and not having any kind of pulling power. Even when shifting to 2nd, 3rd, 4th and 5th gears, it barely maxes out at 30MPH (top speed unless vehicle is on a slope or slight decline then I can get up to and over 40MPH. Checked brake fluid level, it’s ok. The fluid’s at max. Clutch is relatively new (April 2014), with only about 13,000 miles on it, if that. It must be cylinder issue. Is there any way to tell whether it's the clutch master cylinder or slave cylinder?
View 5 RepliesFord Transmission :: Slow Shifting In Gears Then Start Slipping / Vibrate For A Few Seconds
I own a 2005 f-250 superduty with the 6L diesel. Just recently when I leave to work in the morning I notice the trans shifts slow through the gears and when it does start to shift it will start slipping then kinda vibrate for a few seconds then finally shifts into the next gear. It will do this through all the gears until I get up to speed on the highway. After it warms up it shifts and drives great until I let it sit for around 8hrs or more. I really hope I don't need a new Transmission considering I bought this truck as is from the dealership just a little over a month ago. I have checked the trans fluid it is full, I even drained all the fluid and replace with new and it still does the same thing.
View 4 RepliesFord Super Duty (1999-2016) :: Transmission Rattle At Low RPM Especially In Lower Gears Under Load
This is an early 99 f250 powerstroke 6spd manual 4wd, is it common or normal to hear a lot of transmission rattle at low rpm especially in lower gears under a load. Starting off from a dead stop it sounds awful until about 1500 rpm where it clears up (or load is reduced). I'm hoping it's just the power pulses going through splined shafts, gears, etc.
210k on the truck, just changed every fluid in it.
I've been a honda owner and mechanic for all of my driving years where shifting at 8500 rpm is common and now I'm having a hard time learning what this thing likes, rpm ranges to avoid, ect; even shifting I find difficult. At least you can heel toe with the pedal arrangement...
Ford Transmission :: 2004 Explorer Reverse In All Gears
I have a 04 Explorer 4.0 4x4 with 130,000 mi. It all started about 3 months ago. The truck would neutral out while driving. After changing tranny fluid and filter, along with rear speed sensor the problem returned after driving 3-4 miles. After digging deeper I found the transfer case was bone dry and fried inside. Replaced the TC and check fluid level again. Back out of garage and drove the vehicle approx. 2 miles. Stopped to grab a coffee and left truck running. Returned to find I had no reverse or drive. This is after driving it to where I was. Towed truck back home.
I noticed the vehicle would start in gear. Replaced neutral safety switch ( grooves properly aligned ). Started truck, reverse lights come on when in reverse.. The problem now is when I put vehicle into R,N,D,3,2,1, the truck does one thing... REVERSE. All gears put truck into reverse, no forward movement at all. I attempted to replace safety switch a couple of weeks ago but was unable to remove the nut holding the lever on. 2 days I spent on that nut. Now I'm wondering if I did something inside the tranny when I was wrenching on that nut for 2 days?
Ford - F150 :: Jerks Pretty Hard When Shifting Through First Few Gears / Cruise Control Shuts Off
My trusty 1994 Ford F150 is starting to show her age, I think. I'm noticing a few issues:
1 - most concerning to me is she jerks pretty hard when shifting through the first few gears during relatively warm weather. The cold snap has abated the issue for now. Had the transmission fluid checked - mechanic said it's fine.
2 - This is a fun electrical issue. I'm driving down the highway when suddenly the cruise control shuts off, as does the speedometer and the digital odometer. The Tach still works, as do the rest of the gauges. Maybe 10 - 15 minutes later, they all come back on. It's done this a couple times.
3# - Really annoying but very minor; when I push down on the foot feed, there's a bit of a squeak in the engine. I'm guessing it's a tensioner pulley on the serpentine belt, but why it would only happen when I give it some gas?
Ford Super Duty (1999-2016) :: 2002 F350 - Shifting Really Sluggish Between 1st And 2nd Gears Only
2002 f350 7.3 ... problems started all of a sudden one day. I have an edge evolution tuner in my stroke. I have it set to make all of my shifts firm. One day it started shifting really sluggish between 1st and 2nd gears only. It don't do it all the time, but it does it more often then it doesn't. I have also noticed when i come to a complete stop and then start out again it seems that it doesn't downshift all the way back to first and when i hit the gas it seems to kinda be stuck between gears and it barely moves until i get the rpms up before it will ease its way into 2nd and the converter locks up.
It shifts a through all the other gears just fine nice and firm like it should, its just the shift between 1st and 2nd. Im wondering if maybe it might be the speed sensors or maybe the tranny filter is getting clogged up? The fluid in it is still nice and red and up to the level it should be. I just bought the truck in october and the fluid was nice and red when i bought it, but who knows if they changed the filter. I have had NO tranny problems with it up until a few days ago when this little problem started.
Ford Ranger / B-Series :: Truck Idles With Very High RPMs When Driving And Shifting Gears
1999 ranger, 2.55 speed. truck idles with very high rpm's when driving and shifting gears. have changed the AIC, mass air sensor. Throttle position sensor and still does it. the AIC has been changed 5-6 times in 6-8 months as parts store kept telling me it was that. What can i look at, check, etc...
View 6 RepliesFord 7.3L Power Stroke (1999-2003) :: Loses Pedal And Engine Died When Shifting Gears
I have a 2000 F350 7.3 213,000 miles. Manual tranny, 2wd. It is my daily driver.
No issues until 2 weeks ago I pulled out and began shift gears when the engine died and I completely lose pedal. The engine does not shut off it goes to idle and the lights and power are fine but I quickly lose acceleration. After a couple seconds and a few pumps on the pedal it comes back. The problem is intermittant. Until yesterday it was only in the morning but then happened on the way home from work. Thinking ti was water in the fuel I used an additive to cure the water.
I changed the fuel filter just after I bought it in April of this year. I know there is a Injector Pressure Sensor that could be the culprit. EGR?
Ford Super Duty (1999-2016) :: 1995 F250 - Shifting Really Hard And Searching For Gears
So I have a 1995 f-250 4x4 with the 460 and a E4od. So when I bought the truck I drive it two hours home and when I got into town it started shifting really hard and searching for gears. So I flushed it and installed a new oil filter because the oil in it was brown. Very brown. And smelled awful. So it shifts good, but what's happening now is that it shifts good in drive when it wants to.
In the morning it works great but when I get in it to leave after school it shifts really late (around 2900 rpm) and hard. So I put it in first and then into second but when it's time for third and I put it in drive it shifts back to first. But if I stop shut it off for a few minutes and turn it back on it works fine. It only does this after it's been sitting in the school parking lot all day. I replaced the mlps but not the connector due to I didn't have time at the moment. Could it be the tps? Something mechanical?
Ford - Explorer :: 1996 - Clicking Sound Then No Forward Gears?
I have a 96 explorer (Eddie Bower Edition) with automatic trans ( not sure which one at this moment)....
Today getting on the freeway as I was getting up to speed I heard what sounded like a click then no longer had any forward gears. After rolling to a stop I tried every gear and nothing I did fell like it wanted to go but it would not move.
The trans fluid did not smell burnt and at most I might have been maybe 1/2 quart low. Where to start and what to check?