Ford - Explorer :: 2003 - Idling Rough With P2196 And P0174 Codes
I've got an '03 Explorer with the 4.0L SOHC that I got for a deal on craigslist as it needed timing chain tensioners. I got that all done and it runs and drives relatively well, but it idles a little bit rough - especially when it's sitting in gear at a stop light. My go-to first attempt for idling issues is to squirt off the MAF sensor, throttle body, and squirt some starter fluid around the vacuum lines to check for vacuum leaks (though it's possible I may have missed a line or two). Neither seemed to work much. I cleared the codes, dumped some Sea Foam and fresh fuel in it and drove it around a little bit and it threw the CEL light, got about 10 mpg, and generally just didn't seem to have as much power as it should (though I have no experience with the 4.0 in a explorer, soI'm not counting that as a hard fact).
I pulled the codes and I've got a:
P2196 (O2 sensor stuck rich - bank 1 sensor 1)
(and)
P0174 (system too lean - bank 2)
That seems kinda weird to me. Bank 1 is rich and bank 2 is lean? That would make it idle and run weird, for sure, but I'm having a bit of a hard time figuring out what would cause that. I think my next step would be to check/replace the plugs, but that's more of a shot in the dark than a proper diagnosis.
Ford F-150 (2004-2008) :: Knocking When Idling Very Rough
My truck is idling terribly and knocks while doing so, little info is
The truck has 170k miles, I just bought it about two months ago and it was running perfect, drove it to the beach two or three times (4 hour drive) no problems whatsoever. Two weeks ago I noticed it start rocking a bit at idle ONLY when warm, check engine light came on so I ran the code and it said the Cam shaft positioning sensor was bad so I replaced both of those, then the next code I got was for the vct solenoids, replaced both of those and the problem is still persisting. It is odd to me in the fact that when its cold, it runs flawlessly, no problem accelerating/idling/maintaining speed/smoke nothing at all.
As soon as it gets warm it will still do everything flawlessly EXCEPT idle. the idle rpm is around 300-400 and it rocks and knocks terribly.. If i am stopped and I apply some throttle in park or nuetral, just enough to get the rpm up to around 800-900, its perfectly fine. no more rocking no more knocking but as soon as i let my foot off the gas it goes right back to feeling like its going to fly out from underneath the hood.
So my question is why is this? What on earth is going on here? and how do I fix it? And why is there not a manual idle control. Ford place said there was likely damage to the head and recommended a full engine replacement.
Ford F-150 (2004-2008) :: 2007 - Idling Rough And Stumbling A Bit
I have a 2007 F-150. Here is the story....
Last summer the truck was idling rough and seemed to be stumbling a bit. Took it to the dealership and had it diagnosed. Had a mis-fire code on cylinders 1 and 3. I was told to do the spark plugs and clean the MAF. After replacing all plugs and cleaning the MAF the truck seemed to run better but it didnt last long before it started doing the same thing. My Edge Evolution started showing misfire codes in cylinders 1 and 3 again and the truck is stumbling like crazy. Here is what i have done:
1. Swapped the plugs from cyl. 1 and 3 with cyl. 5 and 7 and the problem followed.
2. I replaced the bad plugs with new ones and i no longer get a code for those cylinders but the truck is still acting the same.
Now I am getting two codes saying the system is running rich on bank 1 and 2 and a misfire code in cylinder 4. I cleaned the K&N filter and replaced the MAF but it is still the same. The truck stumbles horribly under a load and has NO power.
History:
2007 F-150 5.4L Lariat
75K miles +/-
K&N Filter
Edge Evolution (has been kept in stock mode)
new spark plugs last summer
new MAF (this week)
New Fuel filter (two summers ago)
Ford 6.0L Power Stroke Diesel :: 2004 F350 6.0L - Idling Really Rough / No Start
I have a 6.0L Powerstroke with about 74k miles. I've owned it about a year. this weekend while driving on the highway at about 55mph i slowed to make a turn. As it came to idle i noticed it was idling real rough. As I accelerated it barely got across the highway. I went to where i was going and let it idle but gave it gas and raised the rpm's to about 1k.
I was concerned it was going to die. As I left it seemed to be better but as i drove it would get real rough and then go away. I accelerated a couple of times engaging the boost and it seemed to be better. I made it home and parked it, but i let it idle before i turned it off.
Now it will not start. it just cranks. everything is pretty much stock. i replaced the fuel filters back in december and also did the blue spring upgrade. I have a OBDII but i didn't have it with me so i wasn't monitoring at the this time. What should be my next step?
Ford Ranger / B-Series :: 2004 - Hard Starting / Rough Idling / No RPMs
backed out of the garage fine later in the day went to put it away started hard would not idle and only rev to 2500 .cleaned map sensor,egg valve tested and it works.cleaned the IAC and that works ,fuel pressure is 58psi. starts hard it would idle now it doesn't dies, no code . with 58psi could the pump still be bad? it has 18 pounds of vacuum. where is the vacuum line for the fuel pressure regulator on the motor?
View 14 RepliesFord F-150 (2004-2008) :: 2006 5.4L Idling Very Rough And Had A Terrible Miss Around 1200 RPM
I have a 2005 5.4 F-150. First off it came to me on a rollback because the owner tried to replace his plugs after he noticed it missing and of course broke one off. So after I extracted the plug from #8 cylinder and installed a new plug I cranked the truck and it was idling very rough and had a terrible miss around 1200rpm. I pulled the codes and got several misfire codes and ignition coil faults on #5,6 and 7 cylinder. Popped in 3 known good coils in these 3 cylinders with no difference.
On Mode 6 on my diagnostic software you could watch the misfire count steadily increase on #7 and every now and then there would be a single misfire on #5 and 6. It also had several codes for O2 sensors biased, stuck rich on that bank. Well since it had a brand new plug and coil, I popped an injector in #7 and havent had a single misfire on it since and it also started idling alot better and all the O2 codes went away. The problem I am having now is #5, 6 and now 8 will randomly misfire, sometimes build up a steady count on one of them, sometimes just skip around between them.
The truck has brand new plugs in all 8 and new coils on this bank also. The truck has 115,000 on it and does have some cam phaser noise on the bank causing the problem, but its not too terribly bad, I have heard alot worse. My problem is something on that bank only as the passenger side bank is fine. I am wanting to say cam phaser now since this is the side with the noise. I have changed them before but have just experienced the noise, never one running like this because of it. Possibly jumped time a little?
Ford F-150 (2004-2008) :: 2006 - Rough Idling When Warm And Dying At Stops Or In Reverse
My brother's 5.4 has been rough idling and dying at stops and in reverse for a few weeks now. Today it threw a code and he finally had me look at it and it's a P0345 code. I was thinking cam phasers possibly, but I didn't think that would cause a code to throw. Also, all I hear about cam phasers is that it makes the truck sound like a diesel, but his when it's about to die sounds like the engine is about to drop out the bottom of the engine bay. Really rough, REALLY loud knocking, etc... What we should be looking at replacing to get this thing back into shape?
View 3 RepliesFord F-150 (2004-2008) :: 2007 XLT Won't Start - Random Rough Idling Spell Or Stall Going Down The Road
I have a 2007 F150 XLT, Supercab 6.5' bed, 4x4 5.4 Automatic with 67000 miles on it. Its not a Flex Fuel
Over the past couple of weeks it would get go through random rough idling spell or stall going down the road. If it was sitting it would idle clear down to 200 RPM's and just sound like an old 'chitty-chitty-bang-bang' car, not a modern marvel of Ford engineering!
I noticed it particularly does it this on an incline. Initially I fixed it by just coasting to where it was flat. I normally keep it above half a tank so i dont think its a fuel pump not getting fed. So I replaced the fuel filter yesterday hoping it was full or clogged, no changed.
This morning it would start at all, I removed the negative terminal on the battery, rolled to the level, tried it 30 times. Nothing. I checked all of my connectors under the hood and the 2 below the cab under the plastic cover. Everything was connected. I disconnected the fuel pressure sensor and it fired right up and runs smoother than since I've owned it.
It hasn't had any CEL lights, until I disconnected that sensor. Should I drop the tank and clean it? Is there any special gasket kits or connectors I should be aware of? Should I just replace that sensor? Is it connected with a chain of sensors I should check first?
Ford - Explorer :: 2004 4.0L - No Start / Crank Rough Like A Few Cylinders Are Zero
Picked up a super nice 03' as is with a no start. It cranks over nice and smooth, sounds like it has proper compression, and has proper fuel pressure. Tried spraying either in it and it will almost catch.
Tried putting a known good coil pack on it, no dice. Usually when other engine slip timing chains, it will crank rough, like a few cylinders are zero. This is not the case.
Ford - Explorer :: 2004 - Rough Idle Like Missing And Die Intermittently
I have a weird intermittent problem. Sometimes when I start my explorer it will idle down and die immediately, I restart and it will idle about 400-600 really rough, sounds like it is missing. When I drive it it is jerky and the acceleration is sluggish but after I get it up to about 20 mph it clears out and then drives and idles fine until I shut it down. Plus these things only happen about every third time (on average) that I drive it. Lastly it's not giving me any codes. What this could be?
View 2 RepliesFord - Explorer :: 2004 V6 Rough Idle - Codes P2104 And P2112
I have a 2004 Explorer with the 4.0L SOHC V6.
I was having some rough idle and a P0401 code for Insufficient EGR Flow. In the process of investigating the EGR valve, I had to remove the throttle position sensor to remove the EGR. After re-installing everything, I had a worse rough idle and I again removed the EGR valve; however this time instead of removing the throttle position sensor, I removed the entire throttle body assembly.
After re-installing everything again, I now have very rough idle and no pedal response. I have the following two codes:
P2104- Throttle Actuator Control System Forced Closed
P2112- Throttle Actuator Control System Stuck Closed
I did not unplug any harness, and all connections are secure. I did not remove the battery cables while working on it, but I did remove the negative cable for about 45 minutes after getting the P2104/P2112 codes hoping a reset my fix things.
Prius (2004-09) :: Engine Will Not Stop Idling And Idles Rough
Just picked up my 2004 Prius from the Toyota dealer body shop. The driver's side was scraped by someone who wanted to be in my lane. Fortunately, we were only going 35 mph. The rear door skin had to be replaced, and most of the side had to be prepped and painted. There are a few silly mistakes: they forgot to replace the driver's door plug, forgot to replace a lower clip, and smudged a tiny area new paint on the bumper. I brought that to their attention and they are going to take care of it... they have to order the plug and clip.
However, as soon as that conversation was complete, it was time for them to close shop. I sat in my Prius, started it, and the check engine light was on. Wasn't on when I dropped it off for the repairs. Also, on the way home, I noticed the engine wasn't turning off when I came to a complete stop (even though the animation says it was off). At idle, the engine is also rough. Looked at the charge bars, and well, there were only two bars showing.
I thought perhaps, though it's not done this before without the animation screen showing it, the engine was on merely to recharge the traction battery. On the way home, the traction battery returned to full charge (green), but the engine still was not turning off when the vehicle was at a complete stop... not was it turning off when coasting... and when arriving home, even with the car in park... and still idling rough. All the while, the animation on the screen is indicating the engine should be off.
When I replaced the traction battery three years ago, I also replaced the 12v with an yellow top Optima. I wouldn't think the Optima is already going bad. I also do not believe in coincidence. I wonder if perhaps some bad fumes have tainted the MAF, or who knows.
Prius (2004-09) :: Rough Idling After Warm Start - Car Vibrate And Engine Struggling
I changed timing belt and water pump DIY back in Oct 2015. Ever since then, I get rough idling (car kind of vibrate and engine kind of struggling) after warm start (no problem with cold starts, it did stall once after the warm start).
Two days ago, I got a P0000 code, I thought it was due to low oil (happened before, I topped off oil 2500 miles ago), so I changed oil and filter. No problem yesterday, but today on my way to work. I got the p0000 code again.
Rough - Mazda - 626 :: 1999 - Rough Idling But Runs Fine At Higher RPM
This problem has been getting worse over the last 2 years. When the car starts it idles fine at about 1000 RPM. As soon as it warms up, it starts to idle rough, between 500 and 750 RPM. It almost quits running. As soon as you give the car some gas it runs just fine. About 3 weeks ago I got a "Engine Lean" check engine light error. I reset the system and have not gotten the error again. Since then I have: changed the MAF cleaned the EGR (made sure it closes completely and ohm out the coils in the actuator) changed the O2 meter on the exhaust manifold cleaned out the throttle body Ohmed out the air idle controller. What I should check next. I was planning to check the fuel pressure in case it is a fuel system problem. It is a 1999 ....
View 5 RepliesFord - Explorer :: 1997 - Engine Just Dies While Idling Now Won't Turn Over At All
1997 Ford Explorer 4.0L the engine just died while idling. The engine will not turn over at all. Battery and cables are good. Able to get engine to turn over with screw driver on starter relay but still won’t start. Checked spark when bypassing relay with screw driver and spark is Ok.
View 19 RepliesExplorer :: 98 Ford Temp Gauge Stuck In The Middle Whether Car Is Off / Idling Or Driving
I have a 98 Ford Explorer 4.0 v6 My temperature gauge is stuck in the middle whether the car is off/idling/driving. I am wondering whether this could possibly be an issue with my coolant temp sensor/sender, or wiring.. Or since its just stuck there, would it be the gears of the actual gauge..
View 1 RepliesFord - Explorer :: 2005 - Stalls After Startup / Shakes A Little When Idling In Park
My truck starts right up, then immediately almost stalls or stalls completely. It also shakes a little when idling while its in Park. I just recently had my egr valve, pcv valve, spark plugs&wires, and fuel filter replaced. it has 104,000 miles on it. What could be causing it to do this?
View 9 RepliesFord - Explorer :: 1998 - Leak Coming From Around Oil Filter / Pulsate When Idling
Ok where to start. I have a 98 ford explorer with a 4.0l OHV engine close to 280,000km. There is a leak coming from somewhere around the oil filter but there seems to be oil coming from more then one spot. Second issue is when a idle the voltage seems to die a bit until I hit the gas and it returns to normal but this issue seems intermediate at times. And I have just replaced the oil filter for the second time no second gasket.
Also I am having a tranny shift flare problem from second to third and when it is under alot of pressure in the bush going up hills it just kicks out of gear and roles back. And another issue is seems like maybe my power steering pump may be bad when I am idiling it seems to pulsate and when I change the position of the steering wheel the pulasting will go away or not be as bad.
Ford - Explorer :: 2002 - Surging At Stop Lights / Sputtering When Idling And Taking A While To Start
I was told by the dealer it would be over 150 to scan and do a fuel trim on my 02 Explorer, XLT, 4.0, Auto. I can't afford the scan or a garage. I paid 4200 for it and a short time later it starts surging at stop lights then it starts sputtering when idling and taking a while to start. Next it stops accelerating past 2.5k, then works well a bit then stops accelerating past 50 miles an hour. Then it works with an 02 disconnected then starts acting up again. It now either runs normal, wont accelorate past certain ranges, or starts then quits 3 seconds later, unless I unplug the MAF then it runs 15 seconds then stalls. Through all this symptoms come and go. Always banks 1 and 2 lean.
Symptoms
Knock
Rough Idle
Slow Starts
Hesitation
Lag
Stall
Replaced
02 Sensors
Fuel Filter
Injectors
Plugs
Plug Wires
Tested
Maf
TP
Temp Sensor
Cam Sensor
Crank Sensor
All EGR Components
Idle Valve
Coil Pack
For any air leaks.
Fuel pressure 37 or higher
Clean Fuel Pump Strainer
Flow tested pump
Checked air filter