Ford 6.0L Power Stroke Diesel :: 2004 F350 Running Rough / Misfire On Cylinders
I have a buddy at work who has an 04 f350 6.0 that is running very rough. we put a scanner on it and disabled the injectors and 1,7,8 have no change. He checked the FICM voltage and is getting 48 volts on crank and run. He checked the wiring for anything loose or rubbed but nothing seems wrong.
View 14 RepliesFord 6.0L Power Stroke Diesel :: Filled Up With Diesel And About A Hour Later The Truck Is Knocking And Idling Rough
Wtf is going on, Temps are all good, no check engine codes...bad diesel fuel? I had 1/4 tank of diesel fuel when I filled it up...
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2004 F350 Truck Will Not Start
A little background, this is an 04, f-350. It sis not start a week ago so I charged the batteries and it started, started fine this morning, (had not driven it for the week) Drove it to work, 35 miles, parked it, and it will not start.
I downloaded Torque and got a few numbers,
HPOP 1900 FMP 48V (repaired last summer) and FVP 11.5V.
Ran out of battery to surf more and look, so I am trying to figure out the app, and the issue with the truck. It seems to turn over good, until I ran the battery down, and the GP cycles normally, and the injector buzz seems good. Temp is in the 50's...
Ford 6.0L Power Stroke Diesel :: 2004 F350 Crank But No Start
I have a 2004 f350 6.0 powerstroke i recently fixed a oil leak in my remote oil cooler and after I was finished it ran fine and ran fine for a few days I noticed yesterday it had a bit of a rough start and some today but would start and run normal. Started the truck this morning and drove it a bit and then let it sit while I went to the dentist came back out and truck wouldn't start. I am getting 200-330 icp with the ipr cycle at 88.5 ficm sync is good and colts are at 12.5 unplugged icp sensor to see if it would start after that and it disnt start so I ruled that out.
I'm currently waiting on AAA to bring my truck home for me but trying to make sure I'm right to start working on it tomorrow. I am thinking the ipr valve is clogged. Am I right to think this may be the issue? When I first installed my remote oil cooler I had the same issue crank no start turned out to be the ipr valve was gunked up and I ended up replacing it 300 dollars later. Then it started and everything was fine. So basically am I right to start at the ipr valve or should I start somewhere else?
Ford 6.0L Power Stroke Diesel :: 2004 F350 Just Died Now Won't Start
M buddy's truck just died and won't start. So far we have changed the ficm because the voltage would fluctuate down to 25, the ficm harness as it was chaffed through and bare wires touching each other, both fuel filter, tested the alternator, new batteries, new air filter and bubble test. The truck spins over and tries to go but won't. I have also tried starting it with the icp disconnected with no change. The secondary filter had lots of bubbles coming into it while filling it for the bubble test, but we did that a few times and no more bubbles. When trying to start you can sound fuel flowing through the secondary filter, is this normal? While trying to start there is black smoke coming out of the tail pipe. We have also tried leaving it plugged in over night and no go.
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2004 F350 - Lack Of Power While Accelerating / Stall And No Start
I have a 2004 f350 with a 03 bullet proofed motor. The truck did not have any power and the turbo wouldn't support until I put a new vgt solenoid in and it ran great for about 3 miles... Stalled doing 65 kinda lacked power while accelerating but got up to speed quick. I pulled over and no start. It is running error code kam on pcm from disconnecting batteries but could this cause the stall and no start? Or should I be looking into icp sensor?
View 2 RepliesFord 6.0L Power Stroke Diesel :: 2004 F350 - Blue Smoke On Hot Start Up
I have a 04 f350 with 175k on it. At around 160k it had new head gaskets, 2-reman heads, egr delete, new oil cooler and it is studded and tuned with SCT and custom tunes.
Since after the head gasket change it seemed to have started blowing a little smoke on the cold starts mainly. In cold weather the starts seem to be harder or slower also. Now for the last 6k-8k miles there is a little smoke at a cold start. But if the motor is warm and it sits for a bit maybe 10 min or less it blows a nice puff of blue smoke or burnt oil.
The smell of burnt oil is mainly on hot starts not cold starts. It does not burn oil running. It will dump some black smoke under acceleration or load. Could this be an injector problem? Or something else? Can't figure it out.
Ford 6.0L Power Stroke Diesel :: 2004 F350 Won't Start / CMP Sensor Code
2004 F350 Lariat 6.0 Crew Cab 6spd... I just bought this truck a month or so ago has been a great running truck since. Before I got it it had headgaskets done, egr valve replaced, and new injectors installed.
Yesterday I shut it off and was setting up my scangauge and doing few other things and noticed I ran the batteries down to 7 volts. So I unhooked them and charged them seperately and cleaned the posts. Now today it won't start. Voltage shows 12.3 FICM logic and main both show 12v and FICM shows 48.5 and doesn't lower when cranking. CMP/CKP shows its not syncing and I am throwing a cmp sensor code. Its had the code since I got it and I've cleared it but always comes back. I've read its rare for a cmp sensor to go bad so I'm wondering if it sounds more like the wiring just seems strange its first time it wouldn't start and hasn't had any other problems.
Ford 6.0L Power Stroke Diesel :: 2004 - After Start Up Rough Idle And Power Lag?
Have a 2004 f250 that is having issues. Once the truck is started the idle goes from normal to loud almost sounds like its going to stall. A few weeks back the same happened when i was on a red light. It choked almost to where it was going to die. I accelerated when light turned green and would not move at all. I had to literally use full throttle to get out the road at about 5 mph. I pulled in to a gas station and fueled up as i had a quarter of diesel left and it stopped the rough idle and power starvation once i started the truck up again. It sees like this time its getting more persistent... FML AND THESE 6.0 problems
View 9 RepliesFord 6.0L Power Stroke Diesel :: 2004 F350 - Battery Light On - Won't Start - Starter?
am in possession of my fianc's F350. The battery light kept coming on, I changed both batteries... twice. I pulled the alt and took it to 2 different stores, asking them each to test it twice, and it checks out good. Drove it to a family function in Sept and it died (no lights, no dings, just completely dead), couldn't get it to jump so I had to have it towed. Tow truck driver said it was probably the starter solenoid, but I couldn't get any confirmation. Had a charger/jumper hooked up to it and got gage movement, dings and heard a clicking sound when I tried to start it.... still no jump. Is this a starter issue, or an electrical issue?
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2004 F350 Crank But Will Not Start / No Injector Buzz
My nephew has a 2004 F350 that will crank but will not start. It will build oil pressure on the gauge. There is no injector buzz and no communication through OBD2 port. Is the PCM dead?
View 10 RepliesFord 6.0L Power Stroke Diesel :: 2004 F350 - No Crank But Will Only Start When Jumped Even With New Batteries
I went out to start my truck yesterday which is a 2004 F350 6.0 Diesel. It wouldn't crank over so of course I tried to jump start it and it fired right up. Went to town while I was there got 2 new batteries and put them in went to start truck and again nothing but will only start when jumped even with new batteries I'm guessing there is a grounding out issue. Where to start?
View 1 RepliesFord 6.0L Power Stroke Diesel :: 2004 F250 V8 - Hard Start / Rough Idle / Shaking - No Power When Cold
I'm new to diesels. I just bought a 2004 F250 with the 6.0 V8. I have the high and low circuit, contribution codes on cylinders 4 and 8. I've only had the truck for a few days but I've been reading a ton. The symptoms are hard start, rough idle/shaking, no power when cold. When it heats up and I'm over 2000 RPM it seems to be just fine. Even when hot and below 2000 RPM it does ok. I've check the FICM. It reads 48V with key on and 48V running. My plan is to do the following:
Change the Fuel Filters
Change the oil filter
Change Air Filter
Change oil with 5-W30 synth and I have both Hot Shot/Rev-X
If that doesn't work, I'll replace the two injectors. How does that sound.
Ford 6.0L Power Stroke Diesel :: Low Power Before Boost Kicks In / Idling Rough With Blueish White Smoke Coming Out Of Exhaust
I just looked back and it has been since July 7th that my girl has been sitting in my shop. Well this past weekend I finally got her back together and started. It took a while to build pressure but she finally came to life..
While I am thrilled that she is running again i have low power before the boost kicks in and is idling rough with a blueish- white smoke coming out of the exhaust. Once i kick her a little she will get up and go but I've never had the smoke before.
I'm thinking maybe a bad injector???
Ford 6.0L Power Stroke Diesel :: 2005 F350 Running Rough - No Power To Move
I got a 2005 f350 6.0 deleted and studded with air dog 2 4g pump, 125k miles. It started running rough then just died all within a few miles tuner showed code for injector 6 and ficm towed into ford dealer didnt have time to mess with it. They said ficm was bad had them replaced it then they said i need whole new fuel system lines,harness,pump,sending unit ,tank the whole 9 yrds. Which i thought was uncalled for so i called up airdog which system i had on there and they laughed and said ford garage is full of bs that they will upgrade my pump to the 4g and new harness.
So I took that stuff to garage had them swap it out and now they said come get the truck they wont work on it anymore that now it needs 3 injectors and they wont touch it with aftermarket fuel system on it. So I go to drive it home and it starts but runs rough and u can hold it to the floor and it wont budge bearly idles up and builds no boost my tuner is showing injector 2,3,4 now which wasn't a problem before i took it into the garage. So im not sure what happened to cause this all to happen but before i sink any more money into it is the 3 injectors enough cause to make it not build boost now .
Ford 6.7L Power Stroke Diesel :: 2011 F350 - Losing Power - Rough Noise - Vibrating?
2011 F350 diesel with 10,000 miles. I have been experiencing problems with the truck loosing power, making rough running noise (pinging like an older diesel), and vibrating. As though the motor is bogging down. It usually occurs on small inclines or hills with the truck in higher gears and low rpms. It will also occur running on flat ground 65-70 mph. Had it occur once while turning the truck around in 1st gear and low rpms. Depressing the accelerator will bring the truck out of it.
This problem occurs randomly sometimes a couple of times a week to not at all. Took to dealer and they found no codes and of couse it didn't do it on the hour long test drive I took the mechanic on. However they did say they had two other owners come in with the same complaints, but could not get trucks to repeat the issue. Problem usually occurs in the hotter part of the day, maybe just coincidence. I had seen similar posts with this problem but no conclusions.
Ford 6.0L Power Stroke Diesel :: 2006 F350 - Bucking / Rough Running
2006 F350 6.0 ... I am piling up parts for a bulletproof party later this summer. It has gotten grumpy ahead of schedule. I will hook up the AE tomorrow for consultation.
In the meantime. Running rough at 50. Seems to accelerate from a stop semi ok. Sitting at idle, holding rpm at 1750 I hear kind of a thump under the hood and the rpm drops 300, then slowly finds it way back to 1750 and it repeats itself.
This thump has not been noticed in the past. Could this be the VGT not working as expected?
Ford 6.0L Power Stroke Diesel :: 2005 F350 - Rough Idle And Low ICP Voltage
My truck is a 2005 f350 6.0, all stock except for an egr delete and 4 inch cat back exhaust. I recently did an oil cooler replacement and egr delete, resealed all 8 injectors, and fixed some wire chaffing at the FICM. it's running great with the exception of idling. It seems like it's idling low but the gauge stays at 750. If I hit the high idle switch, it does fine. Red lights are stressful because it shakes and sounds like it's going to die but never does. I'm posting screenshots of my Torque pro.
I have a SC2 as well but I honestly like Torque better so that's what I use most. I know my ICP is low, but 8 don't know why. No oil in the connector, and no change when I unplug it. The ICP sensor may be a month old with 1000 miles on it. This was taken at a hot startup, sitting in park. When i say hot, I mean I had driven about 60 miles. This is sitting still in drive. ICP voltage finally climbs over 1.0 when i get going about 15mph at around 1250 rpm. The second pic the ICPV is actually higher than normal. It usually stays at .8 until I give it gas.
Ford 6.0L Power Stroke Diesel :: 2007 F350 Not Starting - Running Rough - FICM?
I just bought a 2007 F350 6.0 two days ago, so I was giving the truck a good wash today using a electric pressure washer. The engine bay was pretty dirty so I decided to take some soap and a brush to it. After cleaning it I let it sit for a while in the sun to dry. (engine was stone cold). After it had completely dried out I go in and it cranked right up. I let it idle for a good minute-minute and a half put it in drive and pulled away slowly, right when I touched the accelerator it started running rough, so I popped it into neutral and let it idle for a sec but it was still running really rough so I cut it off not wanting to damage anything worse.
I let it sit and tried to start it again, it just turned over and over. I checked the oil level it was good. So I pushed it back into my driveway to figure it out. I took ICP connector out and tried to start it, just turned over and over. took fuel filter out it was just replaced 2K miles ago it looked a little dirty but not super bad. I put that back in. took icp out again and tried to start it and it started but ran super rough and was dumping black smoke out.
I checked back all ficm connectors and they were all connected. I haven't checked the voltage on that yet, but plan to do that tomorrow. the previous owner had the ficm go bag about a year ago and he sent it off to ficmrepair.com and they fixed it for him. also he had the stand pipes and dumby plugs done as well as the stc on hpop. im kinda at a loss on where to go now other than to check voltage on ficm.