Ford - Explorer :: 2003 - Grinding Or Humming Sound Coming From Left Driver Side Front
Alright so I'm having a problem with my 2003 Ford Explorer. I've recently noticed that when I get to above 40 mph, if my steering wheel is straight, I hear a loud kind of grinding or humming sound coming from my left driver side front. If I am going about 65 mph, it gets even louder and if I crank the steering wheel to the left, that's when it really gets noisy but as soon as I crank it to the right, the problems gone. When I do hear the hummin sound, I can feel it in the steering wheel. I have replaced al of the tires and it didn't work. Also, the car slightly pulls me to the right.
View 10 RepliesFord - Explorer :: 1996 - Grinding / Rattling Type Noise From Front Driver Side At Low Speeds
I have a 1996 Ford Explorer (4WD model). Approximately 4 months ago I had a new set of tires put on it, and in the process of replacing the tires the shop noticed that I had a bad ball joint and one of my wheel bearings was going bad. They said the ball joints were known for completely failing, but the wheel bearings usually didn't, so they recommended that the ball joint be replaced first. That is what I had them do. I haven't had the money to get the wheel bearing replaced yet. This past week it got worse to the point where I can hear it now.
At low speeds I can hear a grinding/rattling-type noise from the front drivers side (that's the side that has the bad wheel bearing). At higher speeds the grinding/rattling-type noise fades away due to road noise, but I can still hear a humming-type of noise that is a bit loader than normal - this noise just started a couple of weeks ago so I'm suspecting that this might also be related to the bad bearing.
I won't have the money to get this fixed for another 2 weeks. In order for me to have the money in 2 weeks I will need to continue working at my job 2 days a week. It's approximately 2 hours round-trip from my home to my job. Obviously with the bearing sounding significantly worse I don't want to drive it any more than I have to, but the only way I can get the money to fix it is to keep driving it back and forth to work.
Here's my question. What risks am I running by continuing to drive this? Am I running the risk of the wheel falling off while I'm driving down the freeway at 70 mph? Am I likely to experience other damaged parts in that area of the vehicle?
Honda - Accord :: 2002 - Grinding Type Noise Comes From Front Driver Side
My wife's car has a grinding type noise (like a key being burnished on a grinding wheel, but lower in pitch). We've had our regular mechanic check the braking system and he finds no irregularities and also says that he didn't see any loose items underneath the engine area. The sound wasn't one of the ones on your excellent 'noises' list, however. The noise comes from the driver side at the front of the car. The car is 2002 Honda Accord LX with 135,000 miles on it. The transmission was replaced under warranty at 70,000 miles.
View 4 RepliesCivic - Honda :: 2010 - Screeching / Grinding Noise From Driver Side Front Wheel - Faulty Brake Pads
I leased a 2010 Honda Civic (non-hybrid) in March of 2010. I had to replace the front brake pads at 8K miles, 18.5K miles and now again at 27K miles. Each time, I get a screeching, grinding noise from the driver-side front wheel. At 8K, I went to a dealership (not the one where I got the car) who replaced them for free "as a courtesy" (apparently, brake pads aren't covered under the warranty). At 18.5K, I went to the dealership where I leased the car from; they said that it didn't look like the other dealer had actually performed the work (yet somehow, the screeching noise went away). They charged me $250 to replace the brake pads and buff the rotors. Now, at 27K, the screeching noise has returned. The dealership has warrantied their prior work and isn't charging me. They claim that there is nothing wrong with the braking system. When I asked them why the pads keep going after 9K miles, they said they don't know, and maybe its the way I brake. I do 80+% highway driving and while I do encounter stop and go traffic on a daily basis, I don't think this is normal.
View 6 RepliesFord F-150 (2009-2014) :: Grinding Noise From Front Driver Side?
First off I have a 2009 F150 4wd 4.6L truck...we have noticed a grinding noise on the front driver side wheel...we have replaced the auto locking hub acuator and the hub assembly but the noise is still there....it has us puzzled now not sure what it could be. I have read many different threads on this issue an it seems that it might be something to do with the vacuum. The noise is only on the driver side and only in 2wd, when its in 4wd it doesn't make the noise at all. Also while in 2wd the noise seems to go away when we let off the gas.
View 5 RepliesFord F-150 (2004-2008) :: Grinding Sound From The Front Driver Side Hub Area
About 3 months ago I started having a grinding sound from the front driver side hub area. I replaced it and it fixed the problem. I read where you should do both because he other one is soon behind it but I waited. Now I started hearing it from the passenger side too. So I replaced it today and all was good until I tested it from 4 wheel back to 2 wheel. Once I went back to 2 wheel the clicking that sounds like bearings going out to me, was back. What is it?
View 1 RepliesFord - Explorer :: 2002 - Driver Side Rear Spring Is Cracked
My uncle has a 2002 Explorer and the driver side rear spring is cracked. I have agreed to fix this as he is on a tight budget and has no mechanical skills or tools for that matter.
Anyhow, I did some reading and have two monroe quickstruts to replace the OEM stuff. I did not want to screw around with a spring compresser and everything else. Were in Michigan, and I can only imagine how rusted the bolts are on this. So I figured getting the whole unit with new hardware would be the best route.
Hopefully these are easy questions. (I do not have the truck to look at right now, and will be doing this Saturday Morning)
I have air tools, Jackstands, 2 floor jacks, a bottle jack, and everything else I need at this point including PB Blaster, rags, pry bars, sockets, etc.
1. I am assuming once I get the truck in the air, I will put the frame on jack stands, and use the floor jacks to manipulate each side of the rear suspension as needed. If I remove the three top bolts, and the bottom bolt holding the shock, can I move the control arm down enough to get the old parts out?
2. What are the torque specs if any for the top three bolts, and the bottom shock bolt? I read the top three bolts are difficult to get out due to limited clearance, so I doubt a torque wrench will fit in there.
3. Would you locktite these top three bolts at all?
4. Weakest question of the day, What are the torque specs for the lug nuts.
5. Anything I have obviously missed? I have done front struts before with a compressor so I am somewhat familiar with the process. Just not on this car before.
6. When Im in this far, anything else I should look at. I will inspect the brake pads etc. Drain and fill the rear diff fluid if needed, etc.
I have searched high and low on the net to find a pictorial write up of the process....
Ford F-150 (2009-2014) :: Grinding / Rustling Noise Coming From Front Driver Side
2011 F150 Limited 4wd 6.2 liter. I just bought the truck a few weeks ago with 26,000 miles. Late last week I began hearing a mild grind/rustling noise that appears to come from the driver's front. It's not terribly loud (loud enough to hear), but it's annoying. It happens when I slow down (on and off the brake and below 25-30 mph) as well as let off and begin to speed up. It doesn't last but a second after I let off the brake and speed up though. The kicker is it does not happen all of the time. I drove it home from work last night and it did not do it one time, but driving to work this morning it happened every time I did what I described above. I have taken it to our local tire/suspension shop and they claim they could not reproduce the sound which does not surprise me. They did a full inspection and found nothing.
View 14 RepliesFord F-150 (2009-2014) :: 2011 2WD - Grinding Noise From Driver Side Front Tire
I have a 2wd 2011 F150 90K with grinding noise coming from the drivers side front tire. Even though it was happening when coasting I thought it might be pads but they are real good. Turning the hub with no tire on it I can hear a little grinding. So I suspect bearings. I want to remove the hub but can't find out how to pull that off.
Where I would expect to find a spindle nut there is an area where it looks like you put a puller in. Can't find any videos or other information on the "Internets". Maybe I'm the first to have bad bearings? Anyway, how to remove the hub?
Ford - Explorer :: 2002 - AC System Low / Luke Warm Air Out Of Driver Side Vents
Well I was recharging my a/c yesterday because the system was low so I used one of them 24oz cans and now I am getting cold air out of my passenger side and luke warm air out of my driver side vents. Also if I switch to the different vents I don't get anything out of the floor only. I get air out when I select it, but it's coming out of the defrost. Other than that everything else works just fine, just no floor. I've read issues with the blend doors but my vehicle doesn't have the dual climate controls so I'm at a loss...
View 4 RepliesFord - Explorer :: 2002 - Driver Side Window Failure Suddenly And Without Warning
The driver's window suddenly, and without warning, collapsed and fell into the door while driving. Fortunately, it didn't shatter.
I pulled the cover and found that the lift cable ball for the fwd track had apparently come out of its receptacle allowing the window to free fall. I hate to just reinstall it as I fear it will happen again and shatter the window.
I heard that possibly Ford has redesigned the cable bracket or some part of the system so that the cable ball can't come loose. Need to know anything about a redesigned bracket or a good way to secure the cable ball? This thing is very difficult to reach and work on, especially for a guy with fat arms!
Ford - Explorer :: 2002 - Entry Pad On Outside Of Driver Side Door Stopped Working
My entry pad on the outside of the drivers door stopped working on my 2002 Explorer. Not only does it not open the doors but they don't light up when push the buttons. I looked in the owners manuel for a fuse related to this but did not see one. Which fuse the number pad is controlled by?
View 5 RepliesFord - Explorer :: 2002 - Left Front Brake Is Pulling Ever So Slightly
At my wits end on this. Left front brake is pulling ever so slightly on my '02 RWD Sport Trac. Just enough to annoy the crap out of me. Sometimes I hardly notice it. Over the past year or so I've flushed and bled the lines after replacing rear wheel cylinders, rebuilt the front calipers and replaced the rotors and pads. It's still pulling. Is there some electronic adjustment for the module that the brake lines come out of? Does the ECM control the pressures?
View 5 RepliesFord Super Duty (1999-2016) :: Shaking And Grinding From Front Driver Side Of Truck
My truck has an intermittent shake with a grinding/binding kind of noise. It seems to happen at lower speeds, generally when slowing down and turning. When I apply the brakes or speed up it seems to stop the noise.
The rubber/plastic seal on the back of the wheel hub is loose on both drivers and passenger side but I don't think that is the problem. I'm wondering if it is the u-joints or something.
The brakes look shiny and i don't see any scratches on them so I don't think there is a rock or something in there. I have the wheel hubs in the auto setting, and it is a 4x4. The truck is a early 99 7.3L with a leveling kit and 230k miles.
Explorer :: 2000 - Grinding Sound Coming From Front Right Side / Steering Wheel Shaking
I just recently bought a 2000 Explorer, 4.0 OHV, 4x4 with about 150,000 miles.
I've had the vehicle for about a month, and ever since I bought it, it's had a grinding sound (sounded like wheel bearing) coming from the front right side. I replaced both right and left bearing/hub assemblies, and took it out for a drive. The initial sound that I thought was bearing noise is still there, and at about 65mph I started to get a little bit of steering wheel shake. I took my foot off the gas and it stopped. I accelerated up to about 70mph and it seemed ok.
I hit a VERY small bump in the road and the steering wheel started shaking like hell. So bad that I almost lost control. I slammed the brakes and the shake stopped instantly. I took it home and put it up in the air, half expecting to see something loose or broken, and everything looks perfect. I re-torqued everything that I had taken apart for the initial hub/bearing replacement, and took it out again. Same issues.
I never had ANY of these problems before I replaced the hub/bearing assemblies, so I'm completely confused. I was thinking CV joints, but I have no clicking at all when turning, in forward or reverse, everything is smooth. Outer tie rods were done about 6 weeks ago..
Ford Super Duty (1999-2016) :: 2002 V10 - Grinding Noise On Driver Side Sounds Like Driving On Rumble Strip
Have a 02 v10 125xxx miles have had grinding noise on drivers side sounds like driving on rumble strip took out the unit hub everything looks good changed out the needle bearing because it was frozen still have sound after needle bearing replacement sound goes away if hubs are locked so question is it the unit bearing or stub shaft...
View 2 RepliesFord - Explorer :: 2002 - Front Right Side Damaged From Running Off Road
My son ran off the road in a neighborhood and hit some large rocks along side the street. It punctured the front right side and obvioulsly damaged the steering because now it drives terribly and instead of the steering wheel handles being side to side it is 90 degrees perpendicular. The service station I use said it has a bent frame and will need to be taken to a body shop. Will the cost to fix it be worth it especially due to its age?
View 2 RepliesNissan - Altima :: 2002 - Grinding Noise From Driver Side Wheel
I've got this 02 Nissan Altima 126,000 miles. I did a front brake job on my self, new rotors and ceramic pads. Immediately after the brake job, I started hearing this horrible grinding noise when weight is shifted to the driver side. It happens when I take apply the brakes or make a right turn. When making a right turn I don't need to apply brakes to hear it. I can sometimes hear it faintly when driving normally.
I took it to my mechanic. He first inspected my brake job, disassembled the rotors and pads, applied brake grease, and reassembled everything. The problem continued. He lifted the car, and had me get in, put it in gear, accelerate, then applied brake, no noise. There is no sign of anything rubbing or grinding in the wheel assembly.
After inspecting the tie rods ends, he replaced the inner and outer on both sides. No Luck. He then replace the ceramic brake pads with regular pads which has reduced the noise but it is still there. I asked around and two other mechanics have suggested the wheel bearings, my mechanic believes this is unlikely.
Durango :: Grinding / Rattling Noise From Front Driver Side
At this point I'm baffled. I've been hearing a grinding/rattling noise from the driver side wheel well for a couple months now. I was positive it was being caused by a bad hub, but the problem persists. Here is what I've done so far:
replaced brake pads and rotors -- twice; once before the hub went bad and once after. The bad hub warped the driver side rotor and afterwards passenger side would not stop squealing for some reason. replaced faulty wheel hub -- The bearing was totally shot, nearly 20* of play in it, should be totally rigid replaced faulty CV axle -- I suspect vibration from the bad hub destroyed the outboard CV joint, making popping/grinding noise while turning or going over bumps filled front differential -- it was a bit low on gear oil The grinding/rattling noise shows up when driving at freeway speed (around 55mph) and gets more pronounced as speed increases. The truck does not do this under acceleration but after speeding up, the rattling is the worst at light throttle (around 2k-2.5k RPM, in 4th gear/overdrive above 55mph).
I noticed that if I shift into neutral at freeway speed, the noise continues until the truck decelerates.
So at this point my thoughts are that it could be a bad differential, but I doubt it because the noise is almost imperceptible in the passenger seat. It could be a bad differential bearing on the drivers side (sounds like a worn out bearing to me). It could be any number of things in the transfer case or transmission.