Honda - Accord :: 1996 - Grinding Noise On The Front Driver Side
I have a 1996 Honda Accord (automatic) with just over 149,000 miles. In the 5 years since I've owned it it's required little more than some new spark plugs and tune up. I currently drive about 30 miles a week, but starting tomorrow I'll be driving much, much more to a new job. Living in Chicago with awful potholes, salt, and traffic, I'm concerned about what may happen in the near future...
I've been getting a grinding noise on the front driver side for years and have never fixed it and never noticed a change...I know it's the tie rod ends/ball joints. I've been warned that the wheel could come off, and as much as I believe them and don't want this to happen, nothing has ever happened. Is this something to do since there has been no change in symptoms or car performance in a couple years?
Other than that, any tips for keeping the car in good, working order? I do oil changes, but are they really necessary every 3000 miles? I have to make it last as long as possible and actually love the car anyway!
Accord :: 1999 Honda V6 - Grinding Noise Coming From Front Driver Side Wheel And Smell Of Rubber
When I slam on my brakes there is a grinding noise coming from the front driver side wheel and the smell of rubber. Also when I do a u-turn the same thing happens. I own a 1999 Honda accord v6....
View 1 RepliesFord - Explorer :: 1996 - Grinding / Rattling Type Noise From Front Driver Side At Low Speeds
I have a 1996 Ford Explorer (4WD model). Approximately 4 months ago I had a new set of tires put on it, and in the process of replacing the tires the shop noticed that I had a bad ball joint and one of my wheel bearings was going bad. They said the ball joints were known for completely failing, but the wheel bearings usually didn't, so they recommended that the ball joint be replaced first. That is what I had them do. I haven't had the money to get the wheel bearing replaced yet. This past week it got worse to the point where I can hear it now.
At low speeds I can hear a grinding/rattling-type noise from the front drivers side (that's the side that has the bad wheel bearing). At higher speeds the grinding/rattling-type noise fades away due to road noise, but I can still hear a humming-type of noise that is a bit loader than normal - this noise just started a couple of weeks ago so I'm suspecting that this might also be related to the bad bearing.
I won't have the money to get this fixed for another 2 weeks. In order for me to have the money in 2 weeks I will need to continue working at my job 2 days a week. It's approximately 2 hours round-trip from my home to my job. Obviously with the bearing sounding significantly worse I don't want to drive it any more than I have to, but the only way I can get the money to fix it is to keep driving it back and forth to work.
Here's my question. What risks am I running by continuing to drive this? Am I running the risk of the wheel falling off while I'm driving down the freeway at 70 mph? Am I likely to experience other damaged parts in that area of the vehicle?
Honda - Accord :: 1998 - Torn Boot On The Front Passenger Side / Grinding Noise
I have a '98 Accord. It's got some issues and I am in the process of buying a new vehicle. But need to have a driveable car for work in the meantime. I have a torn boot on the front passenger side. Front brakes are also pretty worn down, not mention the Cat converter is shot and rusted. I'm getting a very loud, grinding noise when I turn to the left. Very loud noise. Some noise when turning to the right but not nearly as loud. My mechanic looked at the car a week ago and told me too many problems to fix the car, get a new one. which I am but it's taking some time. I'm just wondering if you think the car is likely safe enough to continue to drive until I get the new car. It's the loud grinding noise that freaks me out.
View 2 RepliesHonda - Accord :: 2002 - Metal Scraping Concrete Type Noise Coming From The Rear
So...I just took my car in last week to replace the TPS and noticed that the car is now making a weird sound when I reverse (out of parking spaces, etc). The sounds seems to be coming from the rear of the car the sound is similar to metal scraping concrete and happens intermittently. I'm wondering if this is a random coincidence or if this could be related to the recent work done on the TPS. If my brakes hadn't been completely replaced a year ago, I'd suspect it might be those. What could cause this sound?
View 5 RepliesCivic - Honda :: 2010 - Screeching / Grinding Noise From Driver Side Front Wheel - Faulty Brake Pads
I leased a 2010 Honda Civic (non-hybrid) in March of 2010. I had to replace the front brake pads at 8K miles, 18.5K miles and now again at 27K miles. Each time, I get a screeching, grinding noise from the driver-side front wheel. At 8K, I went to a dealership (not the one where I got the car) who replaced them for free "as a courtesy" (apparently, brake pads aren't covered under the warranty). At 18.5K, I went to the dealership where I leased the car from; they said that it didn't look like the other dealer had actually performed the work (yet somehow, the screeching noise went away). They charged me $250 to replace the brake pads and buff the rotors. Now, at 27K, the screeching noise has returned. The dealership has warrantied their prior work and isn't charging me. They claim that there is nothing wrong with the braking system. When I asked them why the pads keep going after 9K miles, they said they don't know, and maybe its the way I brake. I do 80+% highway driving and while I do encounter stop and go traffic on a daily basis, I don't think this is normal.
View 6 RepliesTouareg :: Electric Motor Or Fan Type Noise Coming From Front Driver Side
Started getting a noise a few minutes after startup. I can hear it click on and then it sounds like a loud electric motor/pump/fan type noise. Starts pretty loud, then gets quieter (but not gone) after 30 secs. If I turn off the engine, it stops and if I immediately restart, it's gone for a couple minutes.
View 5 RepliesElantra MD (2010-15) :: 2013 - Rubbing Type Noise In Driver Side Front When Braking And Turning Right
I have a 2013 Elantra. There is a rubbing type noise in the driver front when braking and turning right. It only rubs(catches) in one spot. Almost like a pulsation, however doesn't pulsate. Hard to describe. Has a new wheel bearing. There are new pads and rotors (two sets of rotors). Took to my Hyundai dealer today. They can't find anything visible. They said only option is to start adjusting/replacing parts as trial and error.
View 3 RepliesFord - Explorer :: 2002 - Front Driver Side Brake Grinding
I have a 2002 Ford Explorer Sport and after a brake job I noticed that while under braking at slow speed there would be a grinding sound on the front left. I replaced the brakes and wheel bearings the first time. After a while I ended up replacing the caliper itself but it still grinds. I don't notice any wheel shaking, pulling and it hasn't locked up although once I did notice a some smoke under hard braking but only once. I also don't hear any grinding while not braking.
View 5 RepliesNissan - Altima :: 2002 - Grinding Noise From Driver Side Wheel
I've got this 02 Nissan Altima 126,000 miles. I did a front brake job on my self, new rotors and ceramic pads. Immediately after the brake job, I started hearing this horrible grinding noise when weight is shifted to the driver side. It happens when I take apply the brakes or make a right turn. When making a right turn I don't need to apply brakes to hear it. I can sometimes hear it faintly when driving normally.
I took it to my mechanic. He first inspected my brake job, disassembled the rotors and pads, applied brake grease, and reassembled everything. The problem continued. He lifted the car, and had me get in, put it in gear, accelerate, then applied brake, no noise. There is no sign of anything rubbing or grinding in the wheel assembly.
After inspecting the tie rods ends, he replaced the inner and outer on both sides. No Luck. He then replace the ceramic brake pads with regular pads which has reduced the noise but it is still there. I asked around and two other mechanics have suggested the wheel bearings, my mechanic believes this is unlikely.
Durango :: Grinding / Rattling Noise From Front Driver Side
At this point I'm baffled. I've been hearing a grinding/rattling noise from the driver side wheel well for a couple months now. I was positive it was being caused by a bad hub, but the problem persists. Here is what I've done so far:
replaced brake pads and rotors -- twice; once before the hub went bad and once after. The bad hub warped the driver side rotor and afterwards passenger side would not stop squealing for some reason. replaced faulty wheel hub -- The bearing was totally shot, nearly 20* of play in it, should be totally rigid replaced faulty CV axle -- I suspect vibration from the bad hub destroyed the outboard CV joint, making popping/grinding noise while turning or going over bumps filled front differential -- it was a bit low on gear oil The grinding/rattling noise shows up when driving at freeway speed (around 55mph) and gets more pronounced as speed increases. The truck does not do this under acceleration but after speeding up, the rattling is the worst at light throttle (around 2k-2.5k RPM, in 4th gear/overdrive above 55mph).
I noticed that if I shift into neutral at freeway speed, the noise continues until the truck decelerates.
So at this point my thoughts are that it could be a bad differential, but I doubt it because the noise is almost imperceptible in the passenger seat. It could be a bad differential bearing on the drivers side (sounds like a worn out bearing to me). It could be any number of things in the transfer case or transmission.
Honda - Accord :: 2003 - Creaking Noise Coming From The Front End / Passenger Side
Have a 2003 Honda Accord with 178K miles on it. Excellent service and maintenance on the car. After this winter (midwest) I notice a creaking sound (like bedsprings) coming from the front end, passenger side. Car also seems rather bouncy on rough roads. Husband check the shocks and struts and says they are fine. What else could it be? Sway bar, ball joints, etc. and estimated cost - will take to a mechanic...
View 2 RepliesHonda - Accord :: Strange Noise Coming From Front Passenger Side Wheel
So I drive a 98 Honda, 118k miles, and for last month I've got a really strange noise coming from my front passenger side wheel. It happens when I apply the brakes, usually at a slow speed, slowing down from something like 30mph to a stop. When slowing down, if I have just a bit of pressure on the brake, the noise seems to go along with the speed of the wheels. It also happens when I accelerate from a stop.
I can only describe it as a kind of creaking noise, almost like it is coming from the spring. Sometimes it sounds a little tinny, sometimes not so much. I don't think its actually in the suspension, because it doesn't make noise if I go over speed bumps or press down on the fender. Brake pads have a good amount of pad left on them.
My hunch is that it might have something to do with the fact that I hardly ever drive anymore, somewhere around 10-20 miles a week, back and forth to the subway essentially (fair amount of time driving down banked turns in a parking garage if that adds any info). My dad knows a decent amount about cars, but he isn't sure what is going on, though he thinks it nothing dangerous. Strange wheel noises always make me wary though.
Ford F-150 (2009-2014) :: Grinding Noise From Front Driver Side?
First off I have a 2009 F150 4wd 4.6L truck...we have noticed a grinding noise on the front driver side wheel...we have replaced the auto locking hub acuator and the hub assembly but the noise is still there....it has us puzzled now not sure what it could be. I have read many different threads on this issue an it seems that it might be something to do with the vacuum. The noise is only on the driver side and only in 2wd, when its in 4wd it doesn't make the noise at all. Also while in 2wd the noise seems to go away when we let off the gas.
View 5 RepliesGolf V R32 :: Occasional Metal Grinding Noise Coming From Front Driver Side
A year ago I heard occasional metal grinding noise coming from the front, sounding like front driver side. Sounded like CV joints that I heard before. The mechanic said it's transfer case/transmission problem, so I replaced the transmission but the noise came back a few days later. The mechanic said to drive it for a while and the noise may go away, if getting worse he can fix it since it has 2-year warranty.
Now a year later the noise becomes predicable and easily reproducible, I went back and asked them to check. They said it may be passenger side axle. I am feeling being manipulated.
Ford F-150 (2009-2014) :: Grinding / Rustling Noise Coming From Front Driver Side
2011 F150 Limited 4wd 6.2 liter. I just bought the truck a few weeks ago with 26,000 miles. Late last week I began hearing a mild grind/rustling noise that appears to come from the driver's front. It's not terribly loud (loud enough to hear), but it's annoying. It happens when I slow down (on and off the brake and below 25-30 mph) as well as let off and begin to speed up. It doesn't last but a second after I let off the brake and speed up though. The kicker is it does not happen all of the time. I drove it home from work last night and it did not do it one time, but driving to work this morning it happened every time I did what I described above. I have taken it to our local tire/suspension shop and they claim they could not reproduce the sound which does not surprise me. They did a full inspection and found nothing.
View 14 RepliesFord F-150 (2009-2014) :: 2011 2WD - Grinding Noise From Driver Side Front Tire
I have a 2wd 2011 F150 90K with grinding noise coming from the drivers side front tire. Even though it was happening when coasting I thought it might be pads but they are real good. Turning the hub with no tire on it I can hear a little grinding. So I suspect bearings. I want to remove the hub but can't find out how to pull that off.
Where I would expect to find a spindle nut there is an area where it looks like you put a puller in. Can't find any videos or other information on the "Internets". Maybe I'm the first to have bad bearings? Anyway, how to remove the hub?
Steering - Pontiac - G6 :: 2006 - Rhythmic Metallic Grinding Noise Coming From Driver Side Front End
I've been hearing a rhythmic, metallic ringy grinding noise coming from the driver side front end of the car that seems to be in time with wheel rotation. It happens between 5 and 40mph, worsens while the steering wheel is turned even the slightest to the right, goes away completely during left turns, reduces and becomes intermittent above 45mph, and between 0 and 5mph, as I turn the wheel to the right from any position, I hear squeaking. I recently had the front control arm, ball joints and struts replaced. It has 140k miles. What could it be?
View 4 RepliesHonda - Accord :: Grinding Noise When Decelerating?
I have a 2001 Honda Accord (automatic) with 128k miles.
I've been having some strange grinding noises coming from the front while driving. It started off a couple of weeks ago as a very low (only some people could even hear it) humming kind of noise. It suddenly got worse one weekend and has now evolved into a louder, clearer grinding sound. Thought it was a wheel bearing, but the shop says it isn't. They think it might be the transmission. Here are some more details and a youtube video of the sound below:
-When accelerating, you can hear a low rhythmic humming, if anything.
-When coasting (not accelerating or braking), especially at speeds below 30 MPH, it makes a much clearer grinding noise that is still very rhythmic.
-When accelerating or braking, the sound goes away or is much lower and less noticeable.
-Appears to be speed dependent and not based on RPM.
-The noise is present when shifting into neutral while moving but not in park or reverse.
Here's a video of the sound: [URL] ..... It's filmed with my phone so it isn't great but you can probably hear it using headphones at a relatively loud volume. You can hear the low thumping/humming a little before 10 seconds in. You can hear the grinding noise from :11 seconds until the end (I'm decelerating), with it most audible after :20.