Ford Super Duty (1999-2016) :: F250 - Trans Shifting Hard / OD Light Flashing / Code P0720
Just got the transmission rebuilt in my truck and other then shifting hard sometimes it has been doing great, Hooked it up to the goose neck this evening and everything was fine then went to back it up and pull it forward and after a short distance the od light was flashing and when i ran a check on it it was p0720? The transmission has less then 1000 miles on it?!?!? 1999 Ford F-250 7.3 Automatic....
View 5 RepliesFord Super Duty (1999-2016) :: Intermittent Tow / Haul Flashing Light When Going Up Or Down Hill - P0720 Code
I have a 2000 F350 7.3 4x4. It began giving intermittent tow/haul flashing light, when going up or down hill but would clear and drive next time truck was cycled off/on. No ABS lights and code reader generated P0720 for the output speed sensor, now I can get it to generate just driving slowly fwd and rev a few times. All of this has been in the last few days.
Truck will stall if I take it up a slight incline with the fault. I replaced the sensor on the top front of the 4r100 transmission and also replaced the sensor on the rear differential after giving up on looking for an output sensor on the transmission. I know the 2WD transmissions have an output sensor but is there one on the 4WD version? I have read several past threads discussing the P0720. I am hoping to confirm what sensor I need to be looking at and where it is located in this application.
Ford Excursion :: Stall Out At Almost Every Stop Light / Code P0720 - Output Shaft Speed Sensor?
I just replaced my starter and on my first ride after replacing it the X started to stumble a bit, and then would stall out at almost every stop light. It threw a CE light and I pulled the code P0720. I searched here and it seems most guys say this is a C.O.P. issue. If it is a bad C.O.P. would it stall like that?
I did have the battery disconnected but I made sure the terminals were clean and tight. Is this a coincidence or did I do something while changing the starter?
Ford Excursion :: 2001 V10 - Getting Code P0720?
I have searched and found a few threads of folks getting a p0720 code and truck revving and dying. Just wondering how to resolve the issue and what the cause was. I have an 01 ex with v-10
View 13 RepliesFord Excursion :: P0720 Code - Output Shaft Speed Sensor
Okay, I have a P0720 code. I bought the Output Shaft Speed Sensor and read that it is on the back end of the transmission.
Need to confirm that it is on top of the transmission, near the tail end? Why are parts that go bad always in the most inconvenient places?
Ford Excursion :: Code P0720 And Engine Stall / Transmission Or Stray Voltage?
Long time Ex owner. This is my second 2000, 4wd, Limited, 6.8 V-10. Just bought this one last month and after two weeks of local driving the following problem showed up:
1. Week of July 5 through 11: With vehicle cold (65*) started and placed in reverse to back out of garage. After slight movement engine stalled like a locked up torque converter or turning ignition off. CEL illuminated. Turned off ignition and restarted. Again in reverse had same stall. Third time no problem but CEL still on. Code is P0720 using "Actron Auto Scanner."
2. Erased Code P0720 (OSS circuit malfunction) and P0307 (Cyinder 7 Misfire Detected). Drove car approx 20 miles without incident. No stumbling, no vibration, no detectable misfire, shifts okay, speedometer okay.
3. Next day with vehicle cold, started to back out of garage and stalled with CEL illuminated and O/D light in shifter blinking. Recycled ignition, started and no O/D light but CEL still illuminated. Vehicle did not stall. Checked code and P0720 set.
4. Replaced OSS on tail shaft of transmission. Same stalling problem with P0720 set.
5. Replaced #7 COP w/aftermarket type to test possibility of bad COP because of earlier P0307 DTC. Same problem exists, first start of the day the vehicle will stall as soon as it starts to move in reverse.
6. Replaced rear ABS sensor. While doing so noticed the ABS sensor wire harness was rubbing the tailpipe and the split, wire conduit was partially melted. Inspected wires (2) within and both appeared okay. Safety wired the harness away from the tailpipe.
7. Let the vehicle sit awhile. Outside Air Temp 84*. Started, placed in reverse, moved a couple of feet and engine stalled and O/D light on steady. Recycled ignition and started again, backed out with no stall or warning lights. No CEL on. Drove 10 miles without incident.
8. Allowed vehicle to cool, started and attempted to back out of garage. Engine stalled, CEL illuminated and O/D light flashing, code P0720.
9. Sunday morning 12 July: 71*, Allowed vehicle to idle in P in garage for 10 minutes before trying to back out. Vehicle did not stall. CEL still on from previous day, no O/D light. Erased P0720 code. Vehicle operating normally.
10. Sunday Noon 12 July: 85*, Started, placed in reverse, backed out and no stall or CEL or O/D light.
After considerable research online at ford-trucks.com found P0720 is a common problem but not easily diagnosed. In most cases the gremlin is COPs and or deteriorated plug boots but in this situation the engine appears to run smoothly and the failure/errors only show up when the vehicle is moved in reverse gear after a cold startup. Once it stalls then restarted it runs fine.
Made a quick check of alternator for failed diode using DVM since I don't have a scanner. Checked okay for voltage and AC ripple. I do have an appointment on Wednesday with my local auto repair shop for troubleshooting. Will have them do continuity check between OSS and PCM and an AC ripple test. Does this sound like an electrical circuit problem or internal transmission problem? Want to make myself as smart as possible when I talk with the techs.
Ford Excursion :: 2000 FWD - O/D Light Flashes - Tranny Shifting Hard Then V10 Dies?
OK, so my 2000 FWD 6.8L Ex has 128k actual miles on the odometer w/ a stock 6.8L from a wrecked later model truck with ~115k actual miles on this 2nd engine from what I was told by the PO/2nd owner (I have no reason to doubt him and I verified the history with the original owner). So I'm guessing that the 4R100 is original without having ever been rebuilt.
I've had zero issues with the drivetrain up to this point, this truck has always run like a top and been very reliable. This afternoon in drive time traffic the overdrive light started flashing and at the same time I noticed that the transmission was shifting really hard (snapping into the next gear) and not in a good way. I was in stop and go traffic when it was shifting weird like this. At one point I make it up to 55+ and I noticed that the O/D light had quit flashing and now it was shifting like it normally does. Then back into stop and go driving the O/D light starts flashing again accompanied by the weird hard shifts.
Next thing I'm sitting there with my foot on the brake fully stopped waiting for traffic to start moving through the traffic signal when out of nowhere and no indication of anything being amiss the engine quits and I get dash lights including CHECK ENGINE and THEFT. I cycle the key off and then try to restart it. It took nearly 10 seconds of cranking to get it to start up however once started everything is back to normal and I have NO trouble lights illuminated including no O/D light and it's back to shifting normally. I continue on in stop and go and highway speed driving for the next 15 minutes like nothing ever happened, transmission is shifting like it always has. The truck has been turned off once and restarted since that incident, yet no other indications of any issue. What's going on?? What to check into?
Ford F-150 (2009-2014) :: 2011 - Wrench Light On With P0720 Code?
I'm having issues when shifting into reverse and I it goes into limp mode when the wrench light shows up. This will not happen when shifting into Drive. When in limp mode I get engine code P0720. This calls for a bad Output Speed Sensor and my research says the sensor is on the back of the transmission but I cannot find any sensors on the transmission. there are several connectors clipped to it but I don't see any bolted in sensors. Also I cannot find a replacement sensor anywhere so I'm wondering if this is a generic code.
View 3 RepliesFord F-150 (2009-2014) :: Wrench Light On Upon Starting And Trying To Put It Into Gear - Code P0720
The last few days I've started getting the Wrench Light on my dash panel upon starting the truck and trying to put it into gear. I first noticed this on a cold morning and got the wrench but the truck went into Reverse and once I got going I was only in 3rd gear. I started and stopped the engine a few times and finally got it going. Since then it seems to do it all the time whether hot or cold. Tonight I noticed that if i start the engine and just go directly into Drive. I don't have the issue but if I ever go into Reverse it goes into limp mode and i get the big yellow wrench again. I only have engine Code P0720 which seems to refer to a speed sensor. I can't seem to find the sensor listed on the typical auto part websites.
View 4 RepliesFord Super Duty (1999-2016) :: 2001 - O/D Light Flashing - Got Code P0720?
I have a 2001 F250 Super Duty with a 5.4L engine, regular cab. The truck has 149000 miles on it. I bought it about a month ago and had the transmission rebuilt, the spark plugs and coils replaced. Apparently the shady dealer I bought the truck from had power washed the engine and there was water in 3 of the spark plug wells on the drivers side. When I got the truck back from the transmission shop and backed it out of the parking lot, the OD off light started flashing and the SEL light came on. The code showed to be a P0720 to which the mechanic at the transmission shop replaced the speed sensor on the top of the tranny.
He said if it comes on again then the speed sensor on the rear differential could be the problem and that he would have to charge me to replace that sensor since it isn't covered under the warranty for the transmission.. I replaced the sensor myself on the rear differential yesterday and thought the problem was fixed. I drove the truck around for 30 minutes with no problems, until I put the truck in reverse, then the OD off light started flashing and the SEL light comes on giving the same P0720 code.
Ford Excursion :: 2000 6.8L - O/D Light Flash Sometimes But No Codes
My O/D Light flash some times, no codes thrown. What could cause it?
View 9 RepliesFord Excursion :: 2000 V10 2WD - Transmission Started Shifting Hard Between First And Second
I have a 2000 V10 2WD Excursion with 104,000 miles. Last week it started shifting hard between first and second, but only when I am between 1500-2k RPMs. If I rev the engine higher, it shifts smooth. I checked the fluid and it is fine. I rarely tow anything except my little trailer to the dump every few months. I have a few questions:
1. Should I drop the pan and change the tranny filter?
2. Should/Can I check the rear diff fluid? (haven't noticed any leaks)
3. Could an inline flush and fill work?
4. I saw a post about a speed sensor in the rear diff. Could this be the issue?
Ford Excursion :: 2002 - Running Very Rough And ABS Light Continuously Flash
I bought my 2002 Excursion 6.8L about 2yrs ago, no less than a week of having it I started to have all sorts of problems. (insert nagging wife here) the biggest of problems was the darn thing started to run very rough and the ABS light cont to flash, then the truck just died (engine stopped, EXTREMELY scary in a intersection) I replaced the VSS in the rear diff.. acted a little better for a while then..no luck. I called around to every ford dealer in town. I need more break light fluid to there isn't enough grease on my wobbler pin?
So I got the initiative to simplify what I was seeing and hearing. I found that there was an OSS sensor on the tail of the transmission...drove my very intense self up to the dealership and bought myself a new OSS sensor. I got home and replaced it, then I drove my truck under the largest shade tree I could find and replaced all the coils and spark plugs. (Insert bloody knuckles and curse words here) Job Done. I thought to myself if this doesn't fix it then I don't know what to do. (I couldn't sell it)...again the point being...the truck has never ran better, gas mileage has doubled and the true power of the v10 has been restored. I found 4 different types of spark plugs in it and 3 different types of coils...?
Ford Excursion :: Brake Intermittent - Hard Pedal And Pulsing Feeling Randomly
I'm having an issue with my brakes. It was very intermittent, but seems to be happening a little more often lately. 99% of the time they work fine.
I'll try to describe. (vaguely) It will sometimes feel like the ABS is engaging, get a very hard pedal and some pulsing feeling. Sometimes just the pulsing without the hard pedal. It will happen at random times. Today it did it in the driveway going 5 MPH. No reason the ABS should think of kicking in.
I feel confident to rule out anything downstream at the wheels. I am leaning towards the master cylinder, but maybe that's wishful thinking. Afraid it also could be something sticking in the ABS which I assume is $$$.
Brake fluid is 18 months old with maybe 20k on it.
Ford Escape / Hybrid :: 2001 - Airbag Light C1414 Flash Code 29
I picked up a 2001 Escape 2.0 manual with 160K. She runs great but I realized that the airbag light was burned out so I hooked up my scanner and pulled 2 codes C1414 and B1869. I changed the bulb and cleared the B1869 but the C1414 remains. the airbag light also flashes and gives me a 29 code. I am not finding much on the subject. The airbags appear to be there and it does not appear that it has been wrecked. I am guessing that it is the airbag control module. Where the module is located on this vehicle.
View 7 RepliesFord 7.3L Power Stroke (1999-2003) :: New PCM Installed - Trans Code P0720
So just got a new pcm installed since i fried the last one anyway. I had a new trans installed almost two weeks ago factory 4r100 now i have a p0720 code. Id take it back to that dealer.
View 8 RepliesFord 7.3L Power Stroke (1999-2003) :: 2001 - Code P0720 Only On 4 - 6 PSI Launches
2001 7.3 Excursion, full mods in sig line.
Recently started getting a P0720 for OSS on 4-6 pound launches, and the X will lurch and then stall out. It drives fine when I drive like a normal person, it also launches fine at 8psi and up (obliterates the tires in the process). Little curious as to where I should start looking beyond the usual culprits on checking the connector for corrosion and verifying the sensor itself is clean/still good.
Stupid thing drives like a peach everywhere else except the 4-6psi LAUNCH ONLY range. Normal driving through that pressure range is absolutely fine. 4-6 is the only problem child area.
Ford Super Duty (1999-2016) :: 2002 V10 - Random Misfire / Pending Code P0720 OSS
I have a 2002 F250 SD V10 4x4, that just started to randomly misfire [does not matter if the vehicle is in motion or in park]. I scanned the OBDII and found pending code P0720 (Output Speed Sensor). The CEL, O/D light, nor the ABS light illuminate. The speedometer functions normally.
This occurred Saturday after we got 12-18" of snow. I cleaned out the driveway, took a short drive (~ miles) & parked the truck (no symptoms). Later we went to 2 stores and then on the way home, the misfire started. The next day the misfire continues.
I have been searching & come up with the same posts that say the issue is not the OSS. It's usually a bad COP or bad wiring @ the OSS. The symptoms are not the same as when I had a COP go bad (only misfired under load between 1500 & 2500 rpm).
Personal issues: My truck does not fit in my garage, it's dark (and usually below 30 F) before I can get to look at it in the evening. Also, we are supposed to get another foot of snow tomorrow night.
Ford Transmission :: 1998 F250 - Code P0720 For Output Speed Sensor Circuit - No Reverse
I bought late 98 F-250, 5.4 G, 4WD. OHad to replace the steering flange because they messed up the ignition cylinder and flange. Truck didn't run for 4 years. 249K miles, no history available. Got the engine running, no DTCs. D, 3, 2, 1 barely moved the truck forward but, R hauled butt in reverse. Checked transmission fluid it was good and clean.
Came back to it a few days later it threw a P0720 (output speed sensor circuit) and I have no reverse, park feels like it wants to move, R is neutral, N is forward, D is forward, 3 is forward, 2 is forward, 1 is forward. The N is full drive. I cleared the P0720 code after it came up and it has not returned. The instrument gauges work but the odometer display is intermittent. Linkage? Fluid? Sensor? Wires?