Ford Escape / Hybrid :: 2002 V6 - CEL Code P0420 For Low Cat Efficiency Bank 1
I have been getting a CEL P0420 for low cat efficiency bank 1 on my 2002 Ford Escape V6. The truck runs fine otherwise. I have ran two loads of Cataclean and the light keeps coming back a few days after CEL reset so I am pretty sure one of cats is done. I am going to replace with an aftermarket cat. My question is, with this code, do I need to replace the front exhaust manifold cat or the rear manifold cat?
View 1 RepliesFord Escape / Hybrid :: 2001 - Airbag Light C1414 Flash Code 29
I picked up a 2001 Escape 2.0 manual with 160K. She runs great but I realized that the airbag light was burned out so I hooked up my scanner and pulled 2 codes C1414 and B1869. I changed the bulb and cleared the B1869 but the C1414 remains. the airbag light also flashes and gives me a 29 code. I am not finding much on the subject. The airbags appear to be there and it does not appear that it has been wrecked. I am guessing that it is the airbag control module. Where the module is located on this vehicle.
View 7 RepliesFord Escape / Hybrid :: 2005 Ford Escape Transmission Fluid Change
So I am changing my transmission fluid tomorrow and was wondering a few things.
1. I noticed some people pull off the transmission hose to the inlet and keep draining that until its clear. For a drain and fill do you do it like that or just pull the plug and refill?
2. When youre filling it back up you just measure how much you taken out and then fill the rest by the dipstick? Anything else i should know?
3. Since I havent changed my transmission fluid in 60,000 miles. I wanted to do a drain and fill. I was thinking I needed to drain and fill it 3 time to catch up to maintenance. How often would you do it to get it clear? Drain and fill then drive it for a week then drain and fill? Or do it all in one day?
Ford Escape / Hybrid :: 2001 - Code P0303 And P0171 / Cylinder 3 Miss And Lean Condition Bank1
Brought home tonight a 2001 Ford Escape 3.0L 24 Valve V6. Bought it from a mechanic who's customer didn't want to put any more money into it. Has 185000 miles on it and it throwing the P0303 & P0171 codes. Cylinder 3 miss and Lean condition bank1.
Mechanic thinks it is a valve seat in the cylinder head next to the fire wall. Before I start replacing the cylinder heads with new remanufactured heads I plan on doing a compression test and leak down test.?
Ford Escape / Hybrid :: How To Reset Oil Change Reminder
How is the oil change reminder reset? Also how is the computer reset for a new new battery?
View 8 RepliesFord Escape / Hybrid :: 2010 - Trans Fluid Change?
Doing trans fluid change on the 2009 -2012? Is it the same as myCD4E drain 4 refill? I know its a different fluid probably buy from Ford.
View 1 RepliesFord Escape / Hybrid :: 2008 V6 - How To Change Belt On Water Pump
How to change belt on water pump on my 08 V6 the hayness says there is a tensioner on the v6 well i am stumped cant find it so ....... Belt is tight I see no way to get slack in belt to change it .top pulley and pump pulley is all i see...
View 11 RepliesFord Escape / Hybrid :: 2011 V6 Won't Start After Spark Plug Change?
I have a 2011 Escape Limited 3.0l V6 AWD. Did a spark plug change at 115k miles for the first time per dealership recommendation. Got new plugs from dealership.
Was pretty cut and dry to replace. Did not check gap on plugs as was told they are not adjustable per dealership. Put pea sized amount of dialectric grease in the COPs and then fitted the plugs into several times with a little spin to coat evenly. Installed plugs to 11 ft.lbs. and reassembled all components without issue. Installed them one at a time so as to not mix up the coils.
I did break the 90-degree nylon quick disconnect for the fuel line that connects to the fuel supply manifold and had to purchase a new hose assembly. Reinstalled without issue.
Went to start up and engine cranks (hiccup sound) but does not turn over. The sound is weak and not a throaty crank like an engine should give. Check engine light flashes on dash and issues a frequent tone also.
Wondering what the issue is? Are they the wrong plugs? Improperly gapped? Possible the fuel line did not pressurize and there is no fuel getting to the plugs for ignition? Kind of stumped as it was a pretty cut-and-dry replacement (if such a thing is possible).
Ford Escape / Hybrid :: Thumping Sound - Steering Wheel Straightens Out But Car Doesn't Change Direction
I was out driving tonight and our 03 escape started making a thumping sound like you hear when you have a flat. I turned the corner and noticed that the steering wheel is now at a 30 degree angle as I'm going straight and when I hit the brakes the steering wheel straightens out but the car doesn't change direction. It's dark so I can only see so much but the tie rods are good and tight from what I can tell same with ball joints. They just did that subframe recall a month or so ago. My concern is steering box but other than these symptoms it seems to be working fine.
View 4 RepliesToyota - Corolla :: 2003 - Check Engine Code P0420 - Change The Converter
I have a 2003 Toyota Corolla, mileage app. 106,000. Check engine light first came on when driving to destination 40+ miles away (most of my driving is shorter, around-town trips). My mechanic said code is P0420 and so they reset it and said if it comes on again that I need a new cat converter. It did not come on until about 6 weeks later when I was on a longer trip again (had driven about 40-50 miles). Can you tell me if the P0420 code absolutely means that a new cat. conv. is needed or if it could possibly be a sensor or something else hopefully less costly than a new cc?
View 3 RepliesFord Escape / Hybrid :: 2008 - Keyless Entry Key Pad Code
Where can I find the key pad code on an 08 escape? I don't have the card in the glove box and I don't want to pay the dealer. It should be printed on the security module box. Where to find it? On my f250 it was under the dash behind radio.
View 14 RepliesFord Escape / Hybrid :: 2006 - O/D Light Come On - Code P0741
I have a Mazda Tribute 2006 2.3. The O/D light would come on, drove it to a friends to scan the check engine light code, and the car almost made it there and then wouldn't remove in reverse, forward, or anything. Turn it off then start it up still wouldn't, then turned it off let it cool and it worked again for a little while.
The code was P0741, just the one code. Took it to a shop to have further tests, they seemed to think it was the clutch was worn and when the fluid heated it lost friction.
Pulled the transmission and thought why not do a Transmission rebuild? I have never done one but there was an awesome video on youtube of the guy doing it so I figured it couldn't be too hard and was just going to try my first rebuild.
According to the guy in the video you always need all new bushing, and we will get a rebuild kit with new clutch packs and the other stuff that comes with those, and sounds like it's a good idea to replace the torque converter.
The car is only at 85K and it looks like the transmission was rebuilt once before he got it at 80K. Maybe a bad rebuild?
Here are some pictures .....
The Input Sprag bearing was shredded and the bushing looks terrible. Can I just replace the bearing and the bushing? Is there any other damage I should be looking for because of this?
The forward planet you can so some eaten metal on the edge and 2 gears spin super smooth and the other 2 you have to push pretty hard to get them to turn. So new forward planet?
The shell's corners look a little rounded I wasn't sure how much was to much, can you tell from the picture if it looks like too much?
Input Sprag
Forward Planet
Sun Gear Shell
Ford Escape / Hybrid :: 2004 3.0l Limited - Airbag Code 36
What airbag code 36 is and how to fix it?
Its a 2004 3.0L limited .....
Ford Escape / Hybrid :: 2002 V6 - Low FTP Signal Below 22v - Code P0452
I'm getting a p0452 fault on my 2002 Escape 3.0 V6 2WD. From what I've read, that seems to indicate low FTP signal below .22v. As I understand it, the FTP sensor has 5 v applied, and the output to the ECU goes down as tank static pressure increases. Conversely, I think the voltage back to the ECU goes up as tank static pressure decreases (for the vacuum leak test measurement).
What the approximate voltage is at atmosphere (engine not running, vent valve open, etc)?
I'm guessing the "less than .22v minimum" signal back to the ECU might look more like either the signal wire shorted to the frame somewhere or the signal wire open (maybe corrosion in the connector)....
Also, where the FTP sensor is located on the Escape and how to access it?
Ford Escape / Hybrid :: 2004 - P0403 Code Came Up For EGR Solenoid
P0403 code that came up on our 2004 Escape 3.0.
Weekend before last I dropped the oil pan, cleaned it and the pickup screen out, and replaced the gasket (switching to full synthetic has been a double edged sword with the leaks that are popping up...); put in new plugs new upper intake manifold gasket and cleaned the throttle body and manifold out. All vacuum hoses inline with the EGR solenoid have also been replaced since the light went on.
While driving the following day the check engine light (CEL) came on and when checked at pep boys read P0403 (no other codes for low EGR flow, etc.). Now, the EGR solenoid is the newest non-regular maintenance item under that hood because the same code came up a couple of years ago (a new solenoid from pep boys fixed that lickety split) so I wasn't overly concerned that it had popped up again, but a bit frustrated that the solenoid only lasted as long as it did. Also, since the light popped up, I have replaced a couple of vacuum lines with some generic 4mm ID (5/32", I think) rubber vacuum hose, but that just headed off what looked like some potential future problem leaks.
Now, here I am a couple of weeks later having tried 4.5 new solenoids (Amazon sent me one with the wrong wiring harness clip so I couldn't verify that it was connected when it didn't work), and thrown some other "just in case" parts at it (new EGR valve and flow sensor, but these may be returned, but may just end up keeping them on, we'll see how things work out). I'm getting a solid reading from the hot lead on the solenoid harness at idle and during static revving, but I can't seem to get anything on the ground pin.
I've cleaned the connections and the larger pin block going into the top of the firewall to no avail. Should this read as a fluttering ground signal all the time, is it only grounded exactly when it wants the solenoid to open the EGR? What can I do to confirm that it should read grounded so I can know one way or the other whether there is a break in the line? I can't find my multimeter (or just dreamed that I picked one up last year). I'm also curious as to whether or not there's a good way to bench test the solenoid. I don't really get a reaction when I hook it up to 12v directly like I do with a vacuum solenoid from my Saab where there's an audible "click."
Is the wire harness for the solenoid a known weak spot? I've found two potential donors at the local junk yard that I can cut the wires out of to play around with/solder a new one in if that's something that the consensus deems may solve my cause. I also had an ABS light come on not too long after the CEL, but when I reset the CEL the ABS light went away and never came back (it only came on when I hit a big expansion joint on a highway bridge, no braking issues since it's been reset and ABS seems to be fully functional, per gravel road test). I still can't seem to read any ground signal at the solenoid harness at idle or with throttle input. I'd like to fix it, but don't want to start digging into the wires blind.
Ford Escape / Hybrid :: 2002 - OD Light Started To Come - Got Code P1744?
2002 Ford Escape... My OD light started to come on every once in a while, and would go off once I turned the car off... This being said, as far as I could tell, the tranny was running smooth. Then an engine light popped on and this code and explanation come up... P1744 "Torque Converter Clutch System Stuck in OFF position".
I recently came back from a bit of a trip... and after shutting the car off, it didn't want to restart. Since this time, the car has begun to start, but the engine light remains on with the P1744 coming up...
Research seems to indicate that the problem is with the Torque Converter Solenoid. You Tube videos show that there are two solenoids just under the transmission pan...
Ford Escape / Hybrid :: 2003 - Airbag Light Error Code 21
Well, I bought a used 2003 Escape for my daughter and without thoroughly researching the airbag light, now have a problem. The light flashes twice, pause, then once, so I think this is error code 21? I cannot find anything on what this code is and how to fix it. I disconnected battery for an hour and now I get 4 flashes, pause, 6 flashes, 46 error.
View 1 RepliesFord Escape / Hybrid :: 2004 - Airbag Light Is Blinking - Code 37?
Girlfriends 04 escape airbag light is blinking code 37. Read something about it being on passenger side what do I look for? I just got done putting in 2 coils, 2 cats, egr, o2 sensor, intake gaskets upper and lower, PCV, injector orings all due to misfire sure there not connected just added info. Other problems include heated seat switch lights for a second then shuts off, and no cruise control. Need to get light off for inspection by end of month....
View 2 RepliesFord Escape / Hybrid :: CEL Code P0403 - EGR Control Circuit Malfunction
After about 6 months I finally got the alternator replaced in the Tribute. I totally forgot about the CEL that was on for EGR Circuit. I've found a couple of pages ( OBD-II Trouble Code: P0403 Exhaust Gas Recirculation Circuit Malfunction ) that explain how to diagnose the issue but I was wondering if any other route for something that may be more common than another thing.
View 2 Replies