Ford 6.0L Power Stroke Diesel :: 2005 - After Replacing Seals In HPOP Now No Start
I have a 2005 ford Excursion 6.0 with an EGR delete, bulletproofed beauty. I bought it about 8months ago and It ran great. I soon bought a 270amp DCpower alternator for it after the batteries died and then replaced the batteries. I eventually developed a no start when hot issue and decided to tear into it my self with everything I've learned on FTE! I love this site and most of you are like legends to me.... so I thought, how hard could this be?
So I bought that fancy icp pressure adapter for testing the pressure from the passenger side valve cover then found one that test pressure at the IPR port. So I went and bought that too 6 0L Powerstroke Specialist's Tool Kit Air Test Tool Ball Tube IPR Sockets | eBay and it lead me to multiple leaks on both sides of the oil rail.
I also bought the CTS2 insight and started monitoring things and realized I had more problems than I thought. I'm still learning how/what to look for and monitor. Anyhow, My EOT and ECT would sometimes be 30-40 Deg. apart. So knew I'd have to replace the oil cooler.
So here I am, I bought ALL ford OEM parts which were -- Oil cooler/standpipes/dummy plugs/ STC update/updated oil drain tubes/Coolant filter/bluespring kit/bango bolts/new degas bottle cap.
I put EVERYTHING in and was careful as can be. I located my leaks and it turned out to be the injector seals on #1 #2 and #5 injectors. The one on the top of the inside of the injectors. So then I bought all new ALIANT injector seal kits (all 8) might as well do them all while I'm in there. And put it back together. Still friggin leaked at injector 1 and 2. So I polished all the nipple cups and bought 8 new ALIANT seals for cups on the rail...STILL LEAKED (swear word).
After putting everything back together and taking it apart 6-7 times...I tried sticking the air directly into the injectors (#1,#2) using a rubber nipple and the injector spill ports were pissing out air. The rest of the injectors ports didn't leak at all except for #3 which was barely a leak.
So after some reading about this problem, I read that this "spill port" leak was normal and could be that the spools were probably closed so it was nothing to worry about. Or that's what I understood.
I put everything back together one more time and got ready for some "long cranking". I should mention I filled the oil valley from the filter housing (about a half a gallon) and cranked for 20sec...Waited 2 mins...cranked 20 sec...waited 2 mins.......continuously untill batteries went dead...then I recharged them and repeated...and recharged them and repeated...I knew It would take a long time but holy cow.
I used the CTS2 to watch my icp volts and it was 0.2 KOEO and while cranking. It didnt change. So I unplugged it. Now I have 1400psi. I tried using my other F350 ICP sensor and same thing. So Its not the sensor. Maybe the harness? So I unplugged the fcim and replugged it back in. Still wont start. I'm at my wits end with this and my wife is hating me for "trying to save money" and blocking the driveway for the last 9 days...
Ford Excursion :: 2004 - Replacing Shocks For Stiffer Ride?
I need to replace the shocks and springs in my truck. I would like a stiffer ride something that doesn't bounce to much and offers better handling.
I have a 2004 4X4 Diesel Excursion
Camry :: Replacing Seals And Water Pump On 2005 V6?
I am bringing in my V6 2005 Camry XLE in for a pulley recall and have reached 90,000 miles. The dealer told me I should also have the timing belt, water pump and engine seals replaced since they are all under the same engine side cover. I am considering the timing belt, but do I need to replace the oil seals and water pump?
View 4 RepliesFord Brakes/Suspension :: Replacing Shocks / Bushing Completely Seized Up To The Bolt
I made a thread in the F150 section but maybe it should have went here. Anyhow I'm replacing the front shocks on my 99 150, and well the bushing was completely seized up to the bolt on the bottom of the shock and I ended up breaking the one side of the shock mount off with it. I can't see any easy way of getting it off, I fear I might run into the same problem with the other side.
Would it be ok to just bolt the new shock back on, sans the forward mount? If its just bolted through the rear bolt hole will there be too much play? I really don't feel like replacing the whole lower suspension arm on this beater truck, and I dont think my welding skills are up to that. I don't think my little stick welder even has enough heat.
Ford Super Duty (1999-2016) :: Replacing Shocks - Rough Ride?
It is about time to replace the shocks on my truck but I am going back and forth between shocks... I have 37s and the ride is rough to say the least I am looking for something to make it feel like I am not riding around on a jack hammer every time I hit a rock.
Dual set up in the front and single in the back and I have steering stabilizers installed.
Ford 6.0L Power Stroke Diesel :: Injectors Leaking Despite New Seals?
I have replaced all the injector seals as well as the ball cup seals but when I crank the truck over after a few cranks I see oil bubbling up from the top of all the injectors. When looking at the injectors from the "top" side all looks well but when I use an inspection cam from down below I can see this happening. Any thoughts?
View 9 RepliesFord Super Duty (1999-2016) :: 2012 F250 - Replacing Shocks And Airbags?
I have a 2012 F250 King Ranch with the FX4 package. I have a goose neck ball and have recently bought a 37' fifth wheel. The rear of my truck sits a touch lower than the front and anytime I'm hooked to a trailer it looks to be squatted way down. It actually is dropping maybe 3". I am looking to replace the shocks which are Rancho's as I have 55k miles on. I'm wondering about shock types, air bags, springs??? Just don't know what my best option is.
View 9 RepliesPassat (B5) :: Replacing Catalytic Converter, Valve Cover, Cam Seals And Timing Belt?
I have some serious work that needs to be done on my car. The catalytic converter needs replacing, and the valve cover gasket and cam adjuster seals need to be replaced. This work falls under their respective warranties. However, I'm wondering if I should have the water pump and timing belt done at the same time as I have 77000+ miles on my car. Is there anything else that would be good to do at the same time as this work. I would be going back to the VW service center for these repairs. Would it save me any money to do this all together?
View 4 RepliesFord - Ranger :: Front And Rear Main Seals Leaking On Rebuilt Engine
The engine runs beautifully, but we cannot stop an oil leak. The Machine Shop replaced the front and rear main crank seal three times and it is still leaking. We took the truck to Ford who put the dye in and checked for the leak with a black light.Their analysis was that they would START with the oil pan gasket. We then took that info to the Machine Shop who said they could see the oil leaking from the rear main and front seal again and replaced the seals in it again. There is still oil leaking from the engine. From the same place. Why we can't seem to stop the leak,and ultimately how to fix the problem?
View 15 RepliesFord Super Duty (1999-2016) :: Vibration / Pinion Seals Leaking
Well, I am getting a vibration In 4x4 99 f250 sd, pinion seals leaking and it has a little bit of movement. I have done a pinion bearing in a crown vic I had before. But not a dana 50. What am I in for, I searched but couldn't find a step by step , how long does it take a back yard guy.
View 2 RepliesFord Ranger / B-Series :: 1994 4x4 - Noisy Rear With Leaking Axle Seals
Really noisy rear with leaking axle seals. Looking to swap in a "yard" unit. Mine has 10" shoes. The door sticker says it's a code 86 rear. If I look for a ranger with a code 86, will everything be the same?
View 5 RepliesPrius (2004-09) :: Replacing New Struts / Shocks
I'm looking at replacing the struts and shocks in my 04 Prius. Last time I replaced them with some cheap KYBs I found on auto parts warehouse. I was hoping for an improvement over the old worn out parts, but didn't feel an improvement. Well after 5+ years and who knows how many miles I figured it was time to replace them again.
View 7 RepliesFord Excursion :: 2000 - Shocks All The Way Around Appear To Be Leaking
My 2000 Ex, v10, 194,000 miles, requires a new stabilizer shock and the shocks all the way around appear to be leaking. Any recommendations for new shocks? The vehicle receives heavy off-road use as well as towing a three horse trailer through mountainous terrain.
View 3 RepliesFord 7.3L Power Stroke (1999-2003) :: E350 - Fresh Coolant Flush Now Seals Leaking
So a dead thermostat forced me to drain the coolant in my E350 7.3L. I noticed the previous owner had green coolant in the van so I decided to do a flush and put in the right coolant. I used Shell Rotella ELC. Well, I noticed after coming home the other day that the van was leaking coolant, upon inspection I noticed its now leaking from the water pump, then today the drain valve sprang a leak! What the HECK is going on!? Is it possible that the seals were shocked when I changed the coolant? Not looking forward to doing a water pump replacement on an E350... sure is crammed under the hood.
View 9 RepliesPrius (2010-12) :: Harsh Ride After Replacing Shocks / Tires
The car was purchased used with 18" wheels already on. After driving for about 6 months, I started noticing the road noise getting very loud. I took the car to a tire shop and they told me that there was some uneven cupping in the middle of the wheels, which is usually caused by worn out shocks making the wheel bounce up and down.
I replaced all 4 shocks, then replaced all 4 tires. Now its much more smooth than before, and is very silent on nicely paved roads. however, I notice when there's roads which any imperfections (like fixed streets with tar.. or uneven pavements, or when your tire hits the freeway markers to keep you in the lane) its heard very loud from inside the car and creates an almost *thud* sound when it does.
I assumed that the problem was that the car had 18" wheels. So recently I swapped the wheels out with stock 15" from Toyota, but somehow the road noise is still very apparent. I sat in a friend's Prius, same year, and I could tell that it was handling the uneven pavements much softer.
What could be the problem now? Is there anything else that needs to be replaced?
Ford 6.7L Power Stroke Diesel :: Grayish / Blueish Smoke On Cold Starts - Turbo Oil Seals Leaking
I've been getting some grayish/blueish smoke on cold starts lately and decided to do some investigation to see if there was a problem or just the cold temps.
I googled it and turbo oil seal problem was pretty common so I figured it was easiest to start there. I removed the pipe between turbo and CAC and it had quite a bit of oil it in. The pipe after the CAC had a fair amount as well. I checked the oil level in the engine and it was slightly down but I can't say how accurate the dipstick is nor it was completely full after the last oil change. Either way, not much oil is entering the intake but I would assume any is too much.
Here's my main concern - What's the likelihood of getting a runaway from this?? Is it possible for the oil seal to fail 'more' than it already has putting more oil in the intake allowing for a runaway condition?
Obviously the turbo needs replaced but is it safe to run it the way it is until it completely fails or replace immediately?
Golf IV / Jetta IV :: Car Came With No Sunroof But Seals Started Leaking
So I bought my 03 golf 2.slow about 10 years ago used and it came with a moonroof... not a sunroof. I never really thought about it and just assumed it was a option from the factory but the seals have been leaking lately and I was looking for a replacement seal and could not find anything only sunroof parts. Is this an aftermarket moonroof where they cut a hole in the roof and added this?..I really hope not. Or did someone take the sunroof assembly out and put this in its place.
View 3 RepliesSubaru - Legacy :: 2000 - Oil Leaking From Engine Seals
As the title says, my car has been leaking oil. I noticed it several months ago and took it to a shop and they said that it it might be leaking from the engine seals. I think they replaced all but the rear seal, because that would have cost a lot more because they would have to pull the engine.
It seemed ok for a while (or maybe I just didn't notice), but now I've noticed that it continues to drip oil, but since it hasn't been fixed by replacing the other seals, I am hesitant to bring it back to the guys who worked on it the first time.
I looked under the car and hood and tried to see if I could tell where the oil is leaking from but it's not apparent to me. I looked at the oil pressure sending switch and, as far as I can tell, I don't see any dripping there, although it does look kinda grimy around that area, but it's hard to tell if it's oil or just run-of-the-mill dirt.
I took a few pics : mauk52.jpg1600x1200
Corolla / Matrix 2009-13 :: Replacing Shocks Absorbers And Struts For Front And Rear
I went into a shop today and got my corolla checked out and they said that its shock absorbers and struts should be replaced because the oils were leaking and they told me the total estimate of my cost (parts+labors) are about 1300 dollars.
Like, do I need to buy all shock absorbers, struts and strut springs for each of the wheel? (front 2 + rear 2 = total of 4 of each) ??