Ford 7.3L Power Stroke (1999-2003) :: Truck Fires Right Up / Runs For 4 Or 5 Seconds Then Stalls Out
So I had a reman 7.3 and 4r100 dropped in my 03 excursion.. since then the engine fires up every single time.. ONLY when the truck sits for 2 days i have this issue where the truck fires right up, runs for 4 or 5 seconds then stalls out.. It starts back up on first try and idles rough 10 seconds then it runs great.. If it only sits 1 day i dont have the issue if it sits 1.5 days it will try to stall out and catches itself from stall out and doesn't stall about 3/4 of the time. The mechanic who is a reputable diesel mechanic cant figure it out.. they called swamps and they also were unsure.
View 9 RepliesFord 7.3L Power Stroke (1999-2003) :: F250 - Truck Would Die While Driving The Truck
I have a little problem with my 1999 f250 7.3 power stroke diesel. Every once in awhile, while driving the truck would die completely but i switch it into neutral and started right up. What could be the problem?
View 9 RepliesFord 7.3L Power Stroke (1999-2003) :: Rough Idle - Stalls Out?
Truck has a rough idle and finally just stalls out. I replace the under valve cover wiring harness and put in new glow plugs. With valve covers still off I started the truck in the issue still persist. I went ahead and unplugged each injector and each time the motor had a hick up .
What am I pulling apart and replacing next?
Ford 7.3L Power Stroke (1999-2003) :: Stalls Randomly And Sometimes Will Not Start
2001 Excursion 7.3 - stalls randomly, sometimes will not start. After the IPR was replaced it was rough for about 4 miles (I thought maybe air in the system), next 40 miles was flawless with 3 stops and restarts. Then it sat for a few hours and I went to leave again and the problem was off and on again for another 5 mile drive. Now it won't start in the driveway. It will start if I disconnect the ICP but the idle is still a little rough.
I replaced the normal culprits after a lot of searching on here:
CPS - replaced with autozone part, thought maybe it was bad new so went to ford and replaced with official part from the dealer
ICP - had oil in the plug and it would idle better removed so I replaced the plug and as much wire as I could - soldered, heat shrunk, good connections - both the pigtail and sensor came from Ford dealer
IPR - replaced with part from the Ford Dealer (FYI - 1 1/8" 1/2" drive craftsman deep socket from sears fit in the ratchet and on the part).
Grounds - found somewhere that the ground on the firewall for the windshield wipers can interfere with the CPS so I pulled it, clean the connections and made sure it was tight and secure.
No check engine light now - I received a few through the process, but did not clear them and there are no codes at this time (self cleared on the 40 mile drive)
I'm thinking it may be some electrical issue/short or a fuel issue at this point, bowl is full and the filter is fairly new (few thousand miles). I haven't done the Hutch mod, but have over 1/2 a tank.
I'm trying to get this going as quick as I can so I don't want to waste too much time, but I also don't want to miss a critical troubleshooting step to take.
Below are my thoughts on the next steps.
Research and test fuel pressure
Tow it somewhere to test each injector - I only have Torque pro to read codes and engine status
If fuel delivery checks out ok, start testing wire by wire on all of the above parts.
Ford 7.3L Power Stroke (1999-2003) :: Engine Stalls After Warming Up For 10 To 20 Minutes
I have a 2002 F250 7.3 4WD automatic with 313,000 miles. A week ago it started stalling after it idled for 10 minutes. It acted like it wasn't getting fuel. It would sputter a few times then just quit. I changed the fuel filter and the truck ran fine the rest of the day. Since that day, it has acted the same way every morning at 1st startup. It idles fine for 10-20 minutes (depending on how cold it is outside), then hesitates a little, then stops. After going through 3 new fuel filters (thinking I had bad fuel), I stopped putting in a new filter every morning, and found that if I just waited 4 or 5 minutes, it would start and run fine after that. It then runs fine the rest of the day.
After it stalls, it will not start right away. I need to wait a few minutes. I've tried draining the fuel filter bowl also. No luck. I tried a new Cam Positioning Sensor. It seems to be related to temperature. It's been getting down to 30 degrees Fahrenheit the past few mornings. It starts fine and idles fine until the temp gauge just starts to move. Then, the stall happens. My fill-up just prior to this happening was with B20 Bio Diesel. I suspected that for a while. But, I've ran all that fuel through plus 4 or 5 regular diesel tanks through, so I no longer think it was related to that. It do see the check engine light when it stalls. I had a shop read my codes and the only code was bad KAM memory. The mechanic said that code shows up all the time on these engines and not to worry about it.
Ford 7.3L Power Stroke (1999-2003) :: 2000 - In Drive Stalls And Dies?
I got a 2000 f350 7.3. Cranks up fine runs fine put in reverse and can back up fine put it in drive and it bogs down and dies. What is causing that.
View 2 RepliesFord 7.3L Power Stroke (1999-2003) :: Cranks / No Start Sometimes Stalls At Idle
1999 7.3l 6spd standard 4x4. Just bought the truck 4 months ago knowing it had a problem that once warm occasionally would t start. Happened a few times every week or two. But wait 15 minutes and the truck would fire back up. Then it started happening more often throughout a day. And I would have to wait longer for it to cool to start it up.
Icp has been changed
Cam sensor
Pulled valve covers to check to see if there were any injector o rings failing. They were all good. Put it all back together.
Pulled the IPR and tore it apart cleaned it all out
Started driving it ran great for a week. Then today sitting at a light the truck died just as if I had turned the key off. Wouldn't start for 3 hours. The. Fired up. Took it to buddies show and started checking things out again. Both batteries load test great and fully charged. Alternator pumping out 13.5 and up.
Codes i have pulled are waste gate to high /low
I forget the number for that one. The second was P1211. Cps has been changed and ipr cleaned. Think that I should replace the ipr of this happens again?
I did get w code a few weeks ago about low voltage at module. this code doesn't appear anymore. Since I checked the plug ins all looks good. But the PCM wasn't mounted properly. So I fixed that up and checked battery connections. They were very good so I re did all of that.
Anyway. Back to the problem. After ipr clean. Drove as she should until sitting at a light a week later. Truck just quit. Would t start back up until cold. Any thoughts. New IPR? Oil in hpop within half inch from top. And I don't seem to have any oil leaks. Did oil change fuel and air filter. Not low on any fluids. I had a 1997 too and threw a bunch of cash at it like this one trying to find the issues.
Ford 7.3L Power Stroke (1999-2003) :: F350 Stalls Shortly After Filling Up
1999 F350. It has the 7.3 diesel engine. His complaint is the truck will stall out on him shortly after filling up. It makes no difference if he is driving at full speed or stopped at a light the truck has stalled in both situations. He reports that he resulted to only filling up to half a tank for a while and that seemed to stop the problem. I was thinking a vent problem. Maybe the gas cap is bad causing a vacuum situation But I have read a few articles about tank delamination and now I'm not sure what to think.
View 1 RepliesFord 6.7L Power Stroke Diesel :: Truck Makes A Metal On Metal Screech When Downshifting From 5th To 4th And 4th To 3rd Occasionally
I've had transmission issues with my truck that the dealers can't seem to duplicate. The truck makes a metal on metal screech when downshifting from 5th to 4th and 4th to 3rd on occasion. The two dealers claim they cannot duplicate the issue and there's no CEL so there's nothing they can do. The shifting is also super slow between gears and regularly hangs in 4th until I let off the pedal for a good two or three seconds. All gear changes are slow.
Now the truck is exhibiting a new issue. When coming to a stop, a second after stopping the truck faintly jerks forward. Almost like the torque converter is not fully unlocked.
Ford 7.3L Power Stroke (1999-2003) :: 2002 - Runs Rough And Stalls After Half Mile?
Here's what I'm dealing with. Took the truck on a 1500 mile trip with no issues. Got home and started it the next morning and it started right up. 1/2 mile from home it starts to run rough and wants to die. It does this for a few minutes and then perks back up and runs fine for however long the trip is. It will always re fire and have no issues. Every morning it's the same game as described above. Within 1/2 from home it's doing this. Seems to be fuel delivery related, but why would it start after sitting overnight, and then after its little fit, run without an issue?
No codes in computer.
Ford 7.3L Power Stroke (1999-2003) :: After Start Up RPMs Drop - Stalls Out Then Idles Rough?
2003 7.3 excursion.. The truck starts every time revs up and idles about 3 seconds then the rpms drop and it tries to stall out catches itself then revs backup and idles rough similar to if you have got air in the fuel lines from changing the fuel filter.. About 1 in five times the truck will stall out and it starts and immediately and idles rough but the rpms and everything runs at speed and rpms don't drop again! This is a reman engine/transmission recently installed.. The mechanic who installed it was unable to figure the problem out.
View 6 RepliesFord 7.3L Power Stroke (1999-2003) :: Crank No Start Sometimes - Stutter / Stalls And Slow Acceleration
I have 2001 F250 7.3L 261k miles.
Over the last few months, I have noticed that my truck is taking longer & longer to start after sitting for a long time (i.e. every morning, after work, etc.) When the problem first started (3-4 months ago) it would crank for 2 seconds & nothing so I would turn it off, let the "wait to start" light go off again (depending on outside temp 10-20 seconds) & then it would crank & usually fire right over like it was new. That seemed to happen only in the morning when it was 70 degrees or colder outside but no problem after work when it was 80+ degrees.
As the weather has gotten colder, it has gotten progressively worse. A couple of weeks ago, it was in the 40s in the morning & it took a solid 8 or 9 minutes of cranking for a few seconds, then trying again before it started. Once it started it did "chuga chug" a couple of times before it smoothed out. Last week when it was 16 degrees in the morning, it wouldn't start at all. I tried for a solid 15 minutes before I gave up.
I will say that as it has gotten worse over the last couple of months, I have noticed that it's cranking w/o firing but I will hear it fire once or twice per crank before it will fire up & run. Once it starts, it runs like a champ. No studders, stalls, slow acceleration, etc. Pulls like it always has. The weirdest part about it is that once it starts & runs for 30-60 seconds, I can shut it off & it'll fire right up every time. If I get it up to full operating temperature, I can go back & start it right up 2 or 3 hours later w/o a problem.
I did notice my oil cooler is leaking pretty badly (that will be fixed this weekend) & my valley has fluid in it but it's hard to tell if it's diesel, oil or a combination of the two because my truck is setup to run on WMO (waste motor oil). I have dual tanks so the OEM tank is diesel & the auxillary tank is WMO. I have 2 mechanical fuel pressure gauges on my fuel bowl, 1 pre & 1 post fuel filter as well as an aftermarket Walbro fuel pump. The fuel pressure when running on WMO has always bounced a little bit between (65-75 psi) but the fuel pressure on diesel has always held solid at 75 psi until recently when I have noticed that it flutters a very small amount between 73-75 psi.
I have verified that the GP Relay works & was leaning towards a glow plug problem but considering it was having troubles at 70 degrees ambient temperature, I'm hesitant to think that's the true problem. I think that might just be adding to the problem. I live in the south so my truck doesn't have a block heater but I'm going to add one this weekend when I replace the oil cooler gaskets & o-rings.
I'm also going to pick up a new Android tablet today (replace my broken one) so I can use the Torque Pro app to monitor ICP, HPOP & InjPW. Finally, I had a DP Tuner chip on it & to remove that as the possible cause, I removed it & the same symptoms continued.
Ford 7.3L Power Stroke (1999-2003) :: Runs Rough Then Stalls - Check Engine Light Came On
I have a 2001 F350 with the 7.3 standard trans. The previous owner put a toggle switch to control the EBPV as an engine brake, I've never used it. It blows white/blue smoke when cold but has for the last 4 years and doesn't seem any worse now.
Last fall I ran the truck the lowest on fuel that I ever have, the light was on for a long time and I thought I would run out. I made it to the gas station and filled it up then drove home. The next time I drove it I went about 25 miles and it started to buck while going up hill. This got worse and eventually the check engine light came on and it stalled.
It wouldn't start again so I had it towed home. I got it started a couple hours later but it would run really rough and only for a minute or so then stall. It will usually start again once or twice and stall, then it wont start again until it has sat for an hour or so.
I didn't have a code reader at the time so I started reading threads. Here's what I've done to date.
Changed the oil and filter, it was way over do. New fuel filter.
The oil level in the HPOP stays about an inch from the top, I've checked it a few times after its stalled.
Dropped the tank and cleaned the screens in the pick up, no change.
The ICP had oil on it so I replaced it and a new connector, no change.
Changed the CSP with a grey one, no change.
Changed the IPR valve with one from a buddy that was on an engine that was running. The truck ran rough for a min then settled down and ran smooth. I let it idle for 20-25 minutes with no problem so I thought the problem was solved. After sitting for a month or so I fired it up and its back to running rough then stalling.
I bought a Vgate ELM327 connector and downloaded FORScan on my laptop. (I'm still not sure what I'm doing). These are the stored codes P1281, P0475, P1316, P0478, P0470, P1211. I cleared all the codes. I did a buzz test cold and the Injectors all sounded the same.
I monitored the truck while running (rough) the IPR is staying around19.92%, ICP is 701.4psi. After 5 seconds the ICP starts to climb and so does the IPR, at 12 seconds the IPR is 37.11 and ICP is 1835.1 psi the it stalls. The fuel pw,ms is around 2.50-3.0 until before it stalls, then its 1.66. The only codes that come up are P0475, P0470, B1473.
Ford 7.3L Power Stroke (1999-2003) :: Truck Won't Go Over 45 MPH
I have a 2003 7.3. Suddenly a week ago when I left work, I noticed my truck wasn't picking up much, but i was in a 40mph zone. I then jumped on the freeway and noticed the truck would not go over 60mph. Once I exited and got on another road with a 55mph speed limit, the truck would not go over 45mph, I had the pedal pressed all the way down and would not go over 2000 rpms. Also, for the transmission to shift, I would have to let off the accelerator.
View 1 RepliesFord 7.3L Power Stroke (1999-2003) :: No Power - Truck Will Crank For About 15 - 20 Seconds Before Turning Over
I have a e99 f350 7.3 all stock. I have no power. The truck will crank for about 15-20sec before it'll turn over. I just purchased the*AE*but am fairly new to understanding it all. In idle its a little rough and when I drive I can only stay in the neighborhood because of fear of getting rearended due to very slow acceleration. Whats weird is that when i have no power while i am driving ill keep the pedal down throw it in nuetral and my rpms and*icp*pressure jump up right away. Things I've replaced:
Icp*sensor
Fuel pump
Pcm
Tps
Cps
Ipr
Dropped tanked and cleaned screens
When cranking my*icp*pressure climbs slowly to right under 500. I dont know what else to do ive been working on this truck dor two months some days 13hs straight, I am feeling defeated. Codes p1249 1211 1209....
Ford 7.3L Power Stroke (1999-2003) :: Truck Wouldn't Go Fast / Plenty Of Power In Low End
2002 f250 7.3l diesel...
I got a new radiator and the tranny fluid was the worst the mechanic had ever seen. He serviced it and warned me that it might not be long for this world. I broke my flexplate and so I had to pull the tranny, and I decided to throw a new torque converter in because it was giving g me symptoms like a broken sprag( it wouldn't rev up or do a brake stand in gear, therefore slow takeoffs).
I was recommended to replace the tranny, I decided I could do the job again down the road if I needed to. About two thousand miles down the road I had a hard shift going from overdrive down to get up a hill and about 10 miles later the truck started slowing down....I couldn't give it enough pedal to keep it going and the engine sounded rough.
I pulled over and checked fluids and everything was fine, truck idled fine, bright red tranny fluid not burnt at all. Pulled on to the road again and it pulled fine until about 40 mph and it wouldn't go any faster. I got it towed home and ordered up a tranny from Ford figuring it must be toast, but I thought I'd throw it out to the forum to see if there is any other troubleshooting I can do before I install the new one in case it is some other problem or some electrical harness or something, or if that is a pretty standard reaction to a fried tranny.
Engine runs good at idle, shifts perfectly to drive and reverse, drives forward and back(I'm very hesitant to drive it out of the driveway in case I can't get it back in). Only happened two times before I decided to tow it. Temps looked fine on the gauges, fluid was a little overfilled in the tranny, but again, not hot or burnt.
Ford 7.3L Power Stroke (1999-2003) :: Truck Would Stumble And Lose Power / Idles But Won't Rev Up
Problem started 2 days ago, driving around and my truck would stumble and lose power. Give it gas, won't rev up but it cleared and ran fine for a mile or so then it comes back (off and on all the way home). Check engine light didn't come on the first few times, came on a couple times on the way home (maybe 4 mile trip) but goes off when the truck runs fine. Thinking it was maybe the fuel pump (got 140K on the stocker). Talked to a few friends, some thought it was algae build up in the tank that was clogging the filter on the pump, underhood filter changed a couple hundred miles ago. Looked fine with slight brown build up at bottom of bowl when I replaced it.
Ran it around yesterday with a friend of mine and his scan tool hooked up, acted up once, check engine came on for a few seconds and shutoff. No code and for some reason we couldn't get it to live data while driving. I dumped in an algae eater yesterday and left the truck overnight since I had to work. Got home this morning to run her around the block to circulate the eater. Truck started and idled fine, went to pull out and she won't rev up, pumped the gas and NOTHING! Check engine light is on now but don't have a scan tool handy to read it. I heard the truck will store the code?
What this problem might be? What's a good scan tool for our trucks that can live data as well? CPS is good and already did the UVCH mod.
Ford 7.3L Power Stroke (1999-2003) :: 2002 F250 Stalls Out And Cranks Hard For 7 - 10 Seconds Before Starting
Truck stalls out and cranks hard for 7-10 seconds before starting if I don't let it warm up adequately before I start driving. Transmission is hesitant to shift. Also, white smoke comes out exhaust if it's cold and I get in the throttle too much or if I hit 70+mph.
View 2 RepliesFord 7.3L Power Stroke (1999-2003) :: Truck Runs Very Rough And Lacks Power When Cold
My truck runs very rough and lacks power when cold, even during the Texas summer. Once it warms-up, everything is fine. It's almost like turning on a light switch. If it's plugged in for a couple/few hours, it's smooth as soon as it starts. I'm assuming it likes the oil once it reaches a specific temperature. What my problem is?
View 14 Replies