Ford 7.3L Power Stroke (1999-2003) :: Rough Idle - Stalls Out?
Truck has a rough idle and finally just stalls out. I replace the under valve cover wiring harness and put in new glow plugs. With valve covers still off I started the truck in the issue still persist. I went ahead and unplugged each injector and each time the motor had a hick up .
What am I pulling apart and replacing next?
Ford 7.3L Power Stroke (1999-2003) :: Stalls Randomly And Sometimes Will Not Start
2001 Excursion 7.3 - stalls randomly, sometimes will not start. After the IPR was replaced it was rough for about 4 miles (I thought maybe air in the system), next 40 miles was flawless with 3 stops and restarts. Then it sat for a few hours and I went to leave again and the problem was off and on again for another 5 mile drive. Now it won't start in the driveway. It will start if I disconnect the ICP but the idle is still a little rough.
I replaced the normal culprits after a lot of searching on here:
CPS - replaced with autozone part, thought maybe it was bad new so went to ford and replaced with official part from the dealer
ICP - had oil in the plug and it would idle better removed so I replaced the plug and as much wire as I could - soldered, heat shrunk, good connections - both the pigtail and sensor came from Ford dealer
IPR - replaced with part from the Ford Dealer (FYI - 1 1/8" 1/2" drive craftsman deep socket from sears fit in the ratchet and on the part).
Grounds - found somewhere that the ground on the firewall for the windshield wipers can interfere with the CPS so I pulled it, clean the connections and made sure it was tight and secure.
No check engine light now - I received a few through the process, but did not clear them and there are no codes at this time (self cleared on the 40 mile drive)
I'm thinking it may be some electrical issue/short or a fuel issue at this point, bowl is full and the filter is fairly new (few thousand miles). I haven't done the Hutch mod, but have over 1/2 a tank.
I'm trying to get this going as quick as I can so I don't want to waste too much time, but I also don't want to miss a critical troubleshooting step to take.
Below are my thoughts on the next steps.
Research and test fuel pressure
Tow it somewhere to test each injector - I only have Torque pro to read codes and engine status
If fuel delivery checks out ok, start testing wire by wire on all of the above parts.
Ford 7.3L Power Stroke (1999-2003) :: Truck Stalls After Downshifting
Lately when I am coming to a stop and roll up to a stoplight/sign in gear the rpms drop too much and it stalls. I let the clutch back out and it starts back, but will stall again if I coast in gear again.
If I just push in the clutch without the rpm's coming up like to change gears it doesn't stall, only when I downshift when stopping and then once I push in the clutch the rpms drop and don't recover.
Truck runs great otherwise, new motorcraft icp and cps doesn't work. Thinking maybe ipr, but idk. I can rev it in neutral and it doesn't stall only when it's under load coasting, it's like the injectors don't recover from being off while coasting in gear.
Ford 7.3L Power Stroke (1999-2003) :: Engine Stalls After Warming Up For 10 To 20 Minutes
I have a 2002 F250 7.3 4WD automatic with 313,000 miles. A week ago it started stalling after it idled for 10 minutes. It acted like it wasn't getting fuel. It would sputter a few times then just quit. I changed the fuel filter and the truck ran fine the rest of the day. Since that day, it has acted the same way every morning at 1st startup. It idles fine for 10-20 minutes (depending on how cold it is outside), then hesitates a little, then stops. After going through 3 new fuel filters (thinking I had bad fuel), I stopped putting in a new filter every morning, and found that if I just waited 4 or 5 minutes, it would start and run fine after that. It then runs fine the rest of the day.
After it stalls, it will not start right away. I need to wait a few minutes. I've tried draining the fuel filter bowl also. No luck. I tried a new Cam Positioning Sensor. It seems to be related to temperature. It's been getting down to 30 degrees Fahrenheit the past few mornings. It starts fine and idles fine until the temp gauge just starts to move. Then, the stall happens. My fill-up just prior to this happening was with B20 Bio Diesel. I suspected that for a while. But, I've ran all that fuel through plus 4 or 5 regular diesel tanks through, so I no longer think it was related to that. It do see the check engine light when it stalls. I had a shop read my codes and the only code was bad KAM memory. The mechanic said that code shows up all the time on these engines and not to worry about it.
Ford 7.3L Power Stroke (1999-2003) :: 2000 - In Drive Stalls And Dies?
I got a 2000 f350 7.3. Cranks up fine runs fine put in reverse and can back up fine put it in drive and it bogs down and dies. What is causing that.
View 2 RepliesFord 7.3L Power Stroke (1999-2003) :: Cranks / No Start Sometimes Stalls At Idle
1999 7.3l 6spd standard 4x4. Just bought the truck 4 months ago knowing it had a problem that once warm occasionally would t start. Happened a few times every week or two. But wait 15 minutes and the truck would fire back up. Then it started happening more often throughout a day. And I would have to wait longer for it to cool to start it up.
Icp has been changed
Cam sensor
Pulled valve covers to check to see if there were any injector o rings failing. They were all good. Put it all back together.
Pulled the IPR and tore it apart cleaned it all out
Started driving it ran great for a week. Then today sitting at a light the truck died just as if I had turned the key off. Wouldn't start for 3 hours. The. Fired up. Took it to buddies show and started checking things out again. Both batteries load test great and fully charged. Alternator pumping out 13.5 and up.
Codes i have pulled are waste gate to high /low
I forget the number for that one. The second was P1211. Cps has been changed and ipr cleaned. Think that I should replace the ipr of this happens again?
I did get w code a few weeks ago about low voltage at module. this code doesn't appear anymore. Since I checked the plug ins all looks good. But the PCM wasn't mounted properly. So I fixed that up and checked battery connections. They were very good so I re did all of that.
Anyway. Back to the problem. After ipr clean. Drove as she should until sitting at a light a week later. Truck just quit. Would t start back up until cold. Any thoughts. New IPR? Oil in hpop within half inch from top. And I don't seem to have any oil leaks. Did oil change fuel and air filter. Not low on any fluids. I had a 1997 too and threw a bunch of cash at it like this one trying to find the issues.
Ford 7.3L Power Stroke (1999-2003) :: Truck Fires Right Up / Runs For 4 Or 5 Seconds Then Stalls Out
So I had a reman 7.3 and 4r100 dropped in my 03 excursion.. since then the engine fires up every single time.. ONLY when the truck sits for 2 days i have this issue where the truck fires right up, runs for 4 or 5 seconds then stalls out.. It starts back up on first try and idles rough 10 seconds then it runs great.. If it only sits 1 day i dont have the issue if it sits 1.5 days it will try to stall out and catches itself from stall out and doesn't stall about 3/4 of the time. The mechanic who is a reputable diesel mechanic cant figure it out.. they called swamps and they also were unsure.
View 9 RepliesFord 7.3L Power Stroke (1999-2003) :: 2003 F350 - Oil Leak When Parked After Running
I have a 03 F-350, 7.3L. There is a slow oil leak that only leaks after I've run the truck. In other words, it doesn't just sit and leak overnight. I'll park it after running, and the next morning I'll notice a small pool of oil, approximately 2" in diameter. The leak appears to be coming from the oil pan area. I degreased the entire oil pan area to get a better visual of where the leak is coming from. I can see oil trailing down the front of the oil pan and the rear of the oil pan. Does this sound like the gasket? Or, what else could it be? I'm praying its not as bad as I think and need to replace the gasket.
View 3 RepliesFord F-150 (2009-2014) :: 2010 - Truck Stalling Shortly After Filling Gas
2010 F-150 with 5.4 has stalled shortly after filling gas tank last 3 times. Truck will restart after much cranking. No other stalls except after filling.
View 3 RepliesFord 7.3L Power Stroke (1999-2003) :: 2002 F350 - Lack Of Power
My issue I'm having - 2002 F350 7.3L has an 8 inch bds lift with 37/13.50 tires. I realize these tires are big but... while driving 100kms/hr or 60 miles per hour and I hit the gas the truck barely wants to move (without pulling a load). Thought maybe a turbo but I have no mechanical skills so here I am!
2nd issue, there's a bullydog chip in that truck when I bought it. he said he always ran it on extreme. I found it puffs way to much black when on extreme and on performance it seems a lot better so that's where I have it?.
3rd issue, the transmission gauge on the dash goes into red when climbing up hills ( I live in the rocky mountains so a lot!) but the bullydog chip says the tranny is only at its hottest 140C? I don't believe that's to hot but I do believe my truck is derating a little while the tranny gauge on the dash is in the red? is there any quick fixes out there for these issues.
Ford 7.3L Power Stroke (1999-2003) :: 2001 F350 - No Power Especially While Towing
I just bought a 2001 F350 diesel with 120k miles on it a couple weeks ago. Friday I headed out to Oregon with my 16 foot enclosed trailer filled with jet skis (about 4-5k pounds) for a competition. A few minutes after being on the freeway I noticed the truck did not have good power. About 30 min later while climbing a steep grade the truck almost went dead.
I started at 60mph and by the time I got to the top i was at 15mph with the throttle pinned. the motor sounded funny and shook the truck more then normal. After wards on the down side of the grade the truck started to act normal. I took it to my buddies house and switched trucks because I didn't trust if for the 13 hour drive.
Today I talked to a mechanic at the dealership and he said that it sounded like injector o-rings to him. I went home, pulled the valve covers and started the motor to see if anything is leaking. steam was coming from the valve area and the down spouts on the injectors was flowing oil. The thing that looked especially abnormal was one of the injectors looked like fuel was dribbling from it. I don't know if that is a problem or not. I couldn't tell if it was fuel or oil but no other injectors had fluid coming out near the wire connections.
Ford 7.3L Power Stroke (1999-2003) :: 2001 F350 - No Power After EBPV Delete
2001 F350 just rebuilt the turbo, did the EBPV delete now no power.
View 5 RepliesFord 7.3L Power Stroke (1999-2003) :: 2000 F350 - Power Mirror Diagram
I need a wiring diagram for my 2000 F-350 power mirrors also to go along with the power window schematics that I posted before.
View 8 RepliesFord 7.3L Power Stroke (1999-2003) :: 2002 - Runs Rough And Stalls After Half Mile?
Here's what I'm dealing with. Took the truck on a 1500 mile trip with no issues. Got home and started it the next morning and it started right up. 1/2 mile from home it starts to run rough and wants to die. It does this for a few minutes and then perks back up and runs fine for however long the trip is. It will always re fire and have no issues. Every morning it's the same game as described above. Within 1/2 from home it's doing this. Seems to be fuel delivery related, but why would it start after sitting overnight, and then after its little fit, run without an issue?
No codes in computer.
Ford 7.3L Power Stroke (1999-2003) :: After Start Up RPMs Drop - Stalls Out Then Idles Rough?
2003 7.3 excursion.. The truck starts every time revs up and idles about 3 seconds then the rpms drop and it tries to stall out catches itself then revs backup and idles rough similar to if you have got air in the fuel lines from changing the fuel filter.. About 1 in five times the truck will stall out and it starts and immediately and idles rough but the rpms and everything runs at speed and rpms don't drop again! This is a reman engine/transmission recently installed.. The mechanic who installed it was unable to figure the problem out.
View 6 RepliesFord 7.3L Power Stroke (1999-2003) :: Crank No Start Sometimes - Stutter / Stalls And Slow Acceleration
I have 2001 F250 7.3L 261k miles.
Over the last few months, I have noticed that my truck is taking longer & longer to start after sitting for a long time (i.e. every morning, after work, etc.) When the problem first started (3-4 months ago) it would crank for 2 seconds & nothing so I would turn it off, let the "wait to start" light go off again (depending on outside temp 10-20 seconds) & then it would crank & usually fire right over like it was new. That seemed to happen only in the morning when it was 70 degrees or colder outside but no problem after work when it was 80+ degrees.
As the weather has gotten colder, it has gotten progressively worse. A couple of weeks ago, it was in the 40s in the morning & it took a solid 8 or 9 minutes of cranking for a few seconds, then trying again before it started. Once it started it did "chuga chug" a couple of times before it smoothed out. Last week when it was 16 degrees in the morning, it wouldn't start at all. I tried for a solid 15 minutes before I gave up.
I will say that as it has gotten worse over the last couple of months, I have noticed that it's cranking w/o firing but I will hear it fire once or twice per crank before it will fire up & run. Once it starts, it runs like a champ. No studders, stalls, slow acceleration, etc. Pulls like it always has. The weirdest part about it is that once it starts & runs for 30-60 seconds, I can shut it off & it'll fire right up every time. If I get it up to full operating temperature, I can go back & start it right up 2 or 3 hours later w/o a problem.
I did notice my oil cooler is leaking pretty badly (that will be fixed this weekend) & my valley has fluid in it but it's hard to tell if it's diesel, oil or a combination of the two because my truck is setup to run on WMO (waste motor oil). I have dual tanks so the OEM tank is diesel & the auxillary tank is WMO. I have 2 mechanical fuel pressure gauges on my fuel bowl, 1 pre & 1 post fuel filter as well as an aftermarket Walbro fuel pump. The fuel pressure when running on WMO has always bounced a little bit between (65-75 psi) but the fuel pressure on diesel has always held solid at 75 psi until recently when I have noticed that it flutters a very small amount between 73-75 psi.
I have verified that the GP Relay works & was leaning towards a glow plug problem but considering it was having troubles at 70 degrees ambient temperature, I'm hesitant to think that's the true problem. I think that might just be adding to the problem. I live in the south so my truck doesn't have a block heater but I'm going to add one this weekend when I replace the oil cooler gaskets & o-rings.
I'm also going to pick up a new Android tablet today (replace my broken one) so I can use the Torque Pro app to monitor ICP, HPOP & InjPW. Finally, I had a DP Tuner chip on it & to remove that as the possible cause, I removed it & the same symptoms continued.
Ford 7.3L Power Stroke (1999-2003) :: Runs Rough Then Stalls - Check Engine Light Came On
I have a 2001 F350 with the 7.3 standard trans. The previous owner put a toggle switch to control the EBPV as an engine brake, I've never used it. It blows white/blue smoke when cold but has for the last 4 years and doesn't seem any worse now.
Last fall I ran the truck the lowest on fuel that I ever have, the light was on for a long time and I thought I would run out. I made it to the gas station and filled it up then drove home. The next time I drove it I went about 25 miles and it started to buck while going up hill. This got worse and eventually the check engine light came on and it stalled.
It wouldn't start again so I had it towed home. I got it started a couple hours later but it would run really rough and only for a minute or so then stall. It will usually start again once or twice and stall, then it wont start again until it has sat for an hour or so.
I didn't have a code reader at the time so I started reading threads. Here's what I've done to date.
Changed the oil and filter, it was way over do. New fuel filter.
The oil level in the HPOP stays about an inch from the top, I've checked it a few times after its stalled.
Dropped the tank and cleaned the screens in the pick up, no change.
The ICP had oil on it so I replaced it and a new connector, no change.
Changed the CSP with a grey one, no change.
Changed the IPR valve with one from a buddy that was on an engine that was running. The truck ran rough for a min then settled down and ran smooth. I let it idle for 20-25 minutes with no problem so I thought the problem was solved. After sitting for a month or so I fired it up and its back to running rough then stalling.
I bought a Vgate ELM327 connector and downloaded FORScan on my laptop. (I'm still not sure what I'm doing). These are the stored codes P1281, P0475, P1316, P0478, P0470, P1211. I cleared all the codes. I did a buzz test cold and the Injectors all sounded the same.
I monitored the truck while running (rough) the IPR is staying around19.92%, ICP is 701.4psi. After 5 seconds the ICP starts to climb and so does the IPR, at 12 seconds the IPR is 37.11 and ICP is 1835.1 psi the it stalls. The fuel pw,ms is around 2.50-3.0 until before it stalls, then its 1.66. The only codes that come up are P0475, P0470, B1473.
Ford 7.3L Power Stroke (1999-2003) :: F350 Won't Crank At All / When Turn The Key To Start Power Drops
New to the forums, not new to fords. 1999 F350 7.3L Diesel. This has been a work truck and has seen multiple devices in and out over the years. I removed the last crap for GPS tracking etc from the last owners. The truck has worked well for a long time since until...
I'm moving slowly to a different state and so the truck got parked for 2 months. went to start it and nothing. the dash comes on and all the lights come on but when you turn the key to start the power drops and nothing.
Testing so far:
replaced the fender Solenoid
tested the starter motor and solenoid -passed
replaced the ignition switch
tested continuity of the hot and ground wires to the fender and starter and everything passed
When I shorted across the fender solenoid the starter works and tries to start the truck (unsuccessfully so far)
So the wire that goes to the fender solenoid is not working and where to trace it to and what needs to be fixed. Is there a relay or fuse besides number 30 that is in the way? where does the magical wire go so i can check its continuity?
I am stuck 800 miles from where i need to be and I am stuck here. I don't have the cash to get a mechanic and my mechanic friends are stumped. I do have a Snapon modus tester, what to do with it.
FYI the batteries are new and fully charged.
Ford 7.3L Power Stroke (1999-2003) :: 2002 F350 - Rough Idle / Lack Of Power
I have a 2002 F350 4wd with the 7.3. I was driving the truck and all of a sudden it was running like crap. the engine light was on. after a minute or so the engine light goes off and the truck is running fine. then again starts running like crap. I am close to the house so I limp it home. runs like crap.... will barley climb small hills. engine light is on. get home turn it off... next day... starts up and runs great for 10 - 15 min. engine light comes back on... runs like crap.... my neighbor says "It's the crank position sensor" I replace it.... runs great for a month.... now it's doing the same thing......
View 9 Replies