Ford 7.3L Power Stroke (1999-2003) :: Driver Side Back Door Won't Open
My driver side back suicide door won't open. It is the top latch that is not disengaging. I think I heard something loose in that door over the past month. Am I going to have to take off the inside panel to fix it?
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: 1271 Injector Code - High Side To Low Side Open Cylinder 1
I've got a 1271 code and I can't seem to make it go away. Code definition is "High side to Low side open Cyl 1". The truck runs fine, no rough idle, no excessive smoke of any color, just the damn CEL light stays on. I check the UVCH and all the injectors ohm in at 2.7 ohms. I've already done the updated clips under the covers. I run all the buzz tests and KOEO/ KOER tests and all appears OK. My AE won't do a Cyl contribution test. All the injector data shows all 0.00. I know its not that perfect. "high to low open", does that mean I've lost a ground? If so where?
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: Extended Cab Driver Side Door Won't Open
I can't figure out the problem with my extended cab door. Driver's side doesn't open with either door handle.
View 13 RepliesFord 7.3L Power Stroke (1999-2003) :: IDM Failure Code And High Side Open Bank 1 And 2
Today I just installed a brand new IDM and after running the Injector Buzz Test test, I received codes: P1298 Injector Drive Module Failure, P1293 Injector High Side Open - Bank 1, and P1294 Injector High Side Open - Bank 2. How a new IDM could throw these codes?
When running the KOEO test I received codes P0605 Injector Control Module Read Only Memory (ROM) Error, P1298, P1293, & P1294.
My engine is still missing but the engine is running a heck of a lot better after replacing the IDM and injector 8 has a rotational velocity of about 3%
Ford 7.3L Power Stroke (1999-2003) :: Code P1271 - #1 Injector High - Low Side Open
Getting DTC Code P1271 - #1 Injector High -> Low Side Open.
The code tends to show up more during cold weather start up. Using AE-AutoEngenuity KOEO - Buzz Test returns the P1271 error
Troubleshooting performed:
- 42-Pin Connector @ Driver Side Valve Cover
- 9-pin VCH on Passenger side
- IDM Module under driver side wheel well
- All of these are testing within the 2.8 - 3.2 Ohm range
- (Used the GB Reman. Tech Bulletin 103) - TB 103: 1994-03 Ford 7.3L IDM Replacement & Diagnostics)
I was going to replace the solenoid, however, with the above readings I'm not convinced it's the solenoid. Before I tear into the valve covers I was looking for some add'l thoughts from the forum. Could it be the IDM ?....
Any add'l checks to perform using AE, or the IDM, other than replacing IDM.
01 Platinum 7.3 - BTS - PHP Hydra Tunes - 4" FloPro - Riff RaffWheel - Redhead Steering - Driven Diesel Hutch/Harpoon - Kenwood DVD w/ back up- 35"s - GloPro EGT/Pyro/Boost/Trans, Scan Gauge II, AE bundle
Ford 7.3L Power Stroke (1999-2003) :: HPOP Reservoir Leaks On Back Side?
have a f550 with a hpop res leak on the backside and wonder if this is in fact under any pressure when functioning since it has o rings on it as well.
View 2 RepliesFord Super Duty (1999-2016) :: Back Doors Won't Open
A while ago both back doors on my 01 crew cab stopped working. The outside handles jiggle loose but the inside ones feel like normal. They both went at about the same time. If it's those little black boxes that mount by the handle on the door, how do I even get to it to change it if it's stuck shut? I can't reach my hand in there either to even try to see what's wrong with it. How to get it open?
View 9 RepliesFord 7.3L Power Stroke (1999-2003) :: 2000 - Doors Rubbing / Rattling Over Bump?
I have a 2000 F250 super cab and the doors rattle going over bumps. I've seen the weather stripping mod and intend to do this but my drivers side doors are touching at the top. Would this indicate that the busings are shot? With the doors open, when I lift on the outer edge there is no movement in the hinge area. The drives door and drivers side back door actually touch and rub at the top. Any pointers?
View 10 RepliesFord 7.3L Power Stroke (1999-2003) :: Cannot Remotely Lock The Doors After Driving For Thirty Minutes
I replaced my gpr on Friday night and my remote to lock the doors worked just fine. Saturday morning they unlocked just fine as well drove it thirty minutes and went to lock my doors with the remote and it didn't work. So could this just be crazy timing for it to stop working or could it be related?
I have a 2000 f250 4x4 I've tested with all three remotes I have for it and none of them work where would I start to test and see if it is just bad connections or dirty ones?
Ford 7.3L Power Stroke (1999-2003) :: Lost Power While Driving And Won't Start Back Up
I have a 2000 f350. Lost power whole driving and won't start back up. I have checked all my fuses and relays several times. Have no power to the fuel pump. Tried running a hot wire straight to the pump and still nothing.checked my emergency cur off switch and there is no power there. Also my WTS light isn't coming on now. Tried checking the heater bowl and no power there.
View 6 RepliesFord Excursion :: 2001 - Any Way To Open Back Doors From The Inside
I have a 2001 triton not that the engine size matters to this question. I've been sleeping in my excursion alot and have been enjoying it, i find exiting out the back doors is much easier but i have no way to open them from a shut position. I do see a cover of a small slotted whole and think it might be part to future customizing but haven't found such a mod. So how I can open my back doors from the inside?
View 9 RepliesFord 7.3L Power Stroke (1999-2003) :: P1273 Code - Cylinder 3 High Low Open
So I got an IDM code and then after running AE buzz test got a P1273 (#3 cylinder high low open).
Ohm'd out the 42 Pin - got 3 across the board. Only test 42 pin from valve cover to injectors.
Double checked UVHC
Swapped solenionds
Swapped injectors
Did ford wiggle test.
Ran Injector buzz between all those steps and still get P1273.
What's the next step? Ohm from IDM to 42pin? May actually be a bad IDM?
Ford 7.3L Power Stroke (1999-2003) :: Red Door Open Light Started Staying On
So my red door open light started staying on. Along with all the lights associated with the doors being opened. The lights don't always come on, but the dash lights stays. As a quick fix I just popped the bulbs out and went on my way. Tried lubing the doors. That didn't work. I started noticing it seemed to be related to when I was slowing down or turning.
I thought maybe it's my passenger leaning on the door around the turns. So I inspected all the doors, they latch fine and don't feel like they're open. Last night I was riding by myself, and I realized that it wasn't anyone leaning on the door. When I would slow down, at the same spot. I would hear a click and the lights by the doors would come on, as well as the light on the back of the cab over the bed.
It did it every time the whole way home. It was approx. 16-18 mph when it would click. It was the same spot each time but I couldn't really nail the exact speed and watch for deer. I originally thought I'd just replace the sensors in the doors, but idk if that'll work anymore since it seems to be affected by other factors.
Ford 7.3L Power Stroke (1999-2003) :: How To Adjust Back Pressure Valve On 7.3L
I just had my turbo and the EBPV on the pedestal rebuilt. Now I need to put it back into the truck. What is the procedure, if any, to adjust the EBPV? I only use the truck to haul a 5th wheel RV and the performance chip closes the EBP valve when going down steep hills -( EXHAUST BRAKE)
View 6 RepliesFord 7.3L Power Stroke (1999-2003) :: Engine Oil Leak From Both Front And Back
Kind of bummed my truck now leaks oil from both the front and back. It's not much volume wise - probably a pint every couple months but before I came up to Alaska it had never leaked a drop. Probably nothing I can do about it barring a rebuild. I have noticed all the guys say not to use any oil additives of any kind. Trying to get it in a shape for another epic journey back down the Alcan highway this fall. Or should I get rid of it and go for a 6.7.
View 10 RepliesFord 7.3L Power Stroke (1999-2003) :: 4R100 Transmission - Leak Towards The Back End
I have a 2000 Ford Excursion 4x4 7.3 with 230K miles, around 15,000 miles ago I replaced the transmission with a rebuilt 4R100, lately I have noticed a leak towards the back end where the transmission and the transfer case connects. Some of the bolts on the bottom of the pan have ATF on them, some others however do not. I have had to add a quart of ATF in the past couple of days in order for it to engage into drive when going from Park to Drive. I have to rev it before it actually kicks in. I'm hoping the leak is just being caused by a gasket either in the pan or connecting the trans to the transfer case..
View 7 RepliesFord 7.3L Power Stroke (1999-2003) :: 2001 F350 Transmission Went Out A While Back
I have a 2001 F350 4x4. My transmission went out a while back. It would only go in reverse. I had it rebuilt and it is still having issues. When I take off with speed from a dead stop it shifts late...about 3000 RPMs. It shifts fine until it shifts into overdrive. It will go into to 4th then right into overdrive causing the truck to act sluggish.
I'm looking into my truck not starting well at any temp too! I didn't know if it could all be connected some how. My mechanic said that when he first started my truck it had a MAP sensor code. He also said that when he unplugged that sensor it didn't change the way the truck ran..Still like crap. I have changed all glow plugs relays and even did the mod to it.
Ford 7.3L Power Stroke (1999-2003) :: Re-soldered The Resistors Back Down - Display Still Dim
Have taken it out about 4 times and re-soldered the resistors back down. I think I probably fried one. The display is still so dim that you have to look real close to see it.
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: Exhaust Back Pressure Sensor
So I have a non ebpv pedestal I was going to clean my sensor on the front because my mileage has went down a bit. My question is is this even worth doing since the valve is not there anymore I have got mixed answers trying to look it up some say it still affects the mileage some say it won't. I cleaned it once about 10 years ago. I have an AE also how do I test it and what should it read if I do need to clean it or replace it?
View 3 Replies