Ford 7.3L Power Stroke (1999-2003) :: Exhaust Leak At Passenger Side Up-pipe To Manifold - P1211 And P1280
I just finished installing a new turbo (shaft play and lots of oil in the compressor side), RR up-pipes, and T500 (250k and once had a very long crank to get the ICP up to start).
Anyway, except for another exhaust leak at the pass side up-pipe to manifold, it seemed to run okay but with lots of white smoke. I only have about 50 miles after the install, when it suddenly starting surging and made a lot of loud knocking noises. This then went away and came back again rather quickly. I was close to home, so I made back under power. I also received the two codes listed. My IPR is original, but two summers ago I installed the IPR re-seal kit. Everything on the IPR looked good when it came off for the T500.
After reading around, I saw that low fuel pressure / air in fuel can cause problems. I connected a pressure gauge to the pre-filter port on the filter housing, and got 40psi at idle. I then took a diesel shower and blew out the fuel line into the tank. After re-connecting it, the fuel pressure stayed the same but the engines idles much better, but still has blue smoke. It's the original fuel pump (to me anyway) and original fuel line connections.
I have about 3/4 tank, and no place to put it, so I'd need to run it out for the Hutch mod, or least to get in there and inspect. Would eliminating the Ford connections at the pump be worthwhile for now, and is 40psi at idle adequate? Wondering if it's time for a fuel pump?
Ford 7.3L Power Stroke (1999-2003) :: Oil Leaking From Driver Side Exhaust Manifold At Junction With Up-Pipe
I had a fuel starvation problem because Ford painted the inside of the fuel tank and the paint was coming off and clogging the filters and because I foolishly drove it I now have white smoke spewing out of the tail pipe and an engine miss.
I also explained that I thought that the white smoke did not smell sweet like antifreeze, but rather like diesel. (Hoping that a head gasket replacement is not required.)
I am in the middle of doing the Hutch Mod with frame-mounted Racor PS120-2 jar-type screen pre-pump filter and shortening my previous Harpoon Mod and paint stripping and powerwashing the inside of my tank. Next I plan to move on toward the engine issue.
This evening I was under the van with a flashlight and I noticed that there was a black liquid of some sort at the driver's side exhaust manifold where it joins the up-pipe. At first I was afraid to touch it fearing that it would be carbon-sooted water, but it felt and tasted like carbon-sooted diesel.
And since I haven't started the engine in two weeks and it has been routinely near or over 100F in Sacramento, water would have likely evaporated days ago.
Does it make sense if the fuel starvation problem caused an injector nozzle or its cup to crack or to stick open or to otherwise spew unburnt fuel into the exhaust manifold which would cause the white smoke? Obviously, the unburnt fuel must get from the affected cylinder(s) to the tail pipe somehow, which likely means out the exhaust valve, through the exhaust manifold to the up-pipe and through the turbo to the exhaust pipe and finally to the tail pipe.
See pictures at my CP. I can't figure out how to attach them or put them inline here because it still says I can't do attachments.
What is my next move? Remove the driver's side valve cover? If so, what should I look for, etc.?
2002 E350 extended body van 7.3 diesel auto trans converted to 4x4 (bought new)
Ford 7.3L Power Stroke (1999-2003) :: 2002 - Oil Leak From Driver Side?
I have a '02 7.3 that has developed a severe oil leak in what seems to be a small line that runs from the drivers side head to the HPOP on the passengers side.
it seems to be leaking at the braket that secures it to the head on the drivers side.
what is this line called and where can i find one A.S.A.P?
Ford 7.3L Power Stroke (1999-2003) :: Drip Leak On The Driver Side
It is still a drip, but is getting worse, for several weeks. May be power steering fluid. I have not found the source. I think it is after the truck has run and has fluids operating under pressure.
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: Small Leak Under HPOP Driver Side Near The IPR
After cleaning entire valley on my 2001 f350 with 7.3 I have found what appears to be a small leak under the hpop drivers near the IPR. HPOP lines are clean and dry. Possible for IPR to leak at 120k miles and what will need to be done to fix.
View 2 RepliesFord 7.3L Power Stroke (1999-2003) :: Oil Leak On Driver Side And Whole Engine Compartment Is Wet
I'm having a problem trying to locate what I assume is an oil leak. It is on the driver side and the whole engine compartment is wet on the side up on firewall beneath the master cylinder. And the whole underneath is wet also axles and leaf spring and can't find where it's coming from. I have sprayed it down with degreaser to try to pin point the leak still no luck. Truck has 236k on it also new hpop and turbo pedestal and checked the valley and its dry. Right now I'm at a loss. I'm leaning towards oil cooler but would a leaking oil cooler cause whole side of engine compartment to be covered?
View 9 RepliesFord 7.3L Power Stroke (1999-2003) :: Leak Under Passenger Side?
I moved my truck before I noticed exactly where it was coming from then after ward looked in the engine compartment. I had a puddle under the passenger side looks like the hoses going into the passenger glove box area (because I saw a few drops on them). The liquid is silvery. Any guess what fluid this is or where it might be leaking.
The antifreeze doesn't seem to be getting lower. I drove it yesterday for about 30 minutes and no crazy leaks.
Ford 7.3L Power Stroke (1999-2003) :: Coolant Leak On Passenger Side
2003 7.3 175,000 miles...
Saw a stain in my driveway where you normally see AC drip. Opened hood and saw degas empty.
Looking around like crazy and find wet area. Where the coolant line turns down beside the passenger fender.
Looks wet near bend going toward running board. Didn't get to inspect much but I pulled back a bit of loom to inspect shape of lines and they look great.
What could be going on?
Ford 7.3L Power Stroke (1999-2003) :: Leak On Front Differential Passenger Side
My 7.3 has a leak on the front diff passenger side. It went into a shop for repair and they did both seal but the passenger side came out with a worse leak than it went in with. So just looked this morning and small pool of oil under the ujoint area on the concrete. Its booked in again to be fixed under warranty repair (place that fixed it, repair came with 2yr warranty) on Wednesday next week - was the earliest I could get.
Question - can i keep driving the truck? I'm making a wild assumption that I can unless I use 4 wheel drive. My intention was to just keep topping up the diff to ensure there is fluid in it. It's the work truck so wouldn't be good to be without....
Ford 7.3L Power Stroke (1999-2003) :: Different Battery Box For Driver Side?
Is there a different battery box or better battery holder for the driver side without all the air filter housing stuff. I had an AFE Big boost filter and when I modified the stock battery box it still had the bottom section of the air filter compartment well after about 4-5 years I was cleaning the filter today and there was a hole rubbed in the filter from moving around and the pre filter is getting holes wore through it. So I cut the air box part off so now the filter will sit on the fiberglass stuff on the fender well. I ordered a couple of the new Blue Donaldsons from RiffRaff to replace the Big Boost filter. The modified filter box looks kinda like a hack job because all I had was a cut off wheel and the plastic got hot and now I have melted buggers all over it. I thought I saw somethin a long time ago about a battery holder out of a van that was just the bottom plate but can't find it anywhere now.
View 8 RepliesFord 7.3L Power Stroke (1999-2003) :: Leaking Power Steering Under The Wheel Arch On The Driver Side
Initially had indications of a leak under the wheel arch on the drivers side.
About 3-4 months back replaced both PS lines and the leak stopped - briefly (maybe a couple a weeks).
Now the leak is back, but what's interesting is I lose more ATF fluid on a single long haul run than I do running round town for 3 weeks. I can't work out where the leak is coming from to identify what else to replace - short of just buying a pump and reservoir and replacing them as I've already done the hoses.
My turbo cooler pipe was hard up against the old PS pipe where it entered the side of the reservoir until I did the replacement hoses. Now I have it out the way but I'm wondering if it's caused some unseen wear or damage.
If I just do the pump to see if that works are the reman units any good out of Autozone or O'reilly's?
Ford 7.3L Power Stroke (1999-2003) :: Driver Side Key Lock Recessed?
'99 F250 SuperDuty. Tumbler is recessed and the key slot is horizontal rather than vertical. I suspect the spring fingered clip has fallen off.
View 2 RepliesFord 7.3L Power Stroke (1999-2003) :: Driver Side Back Door Won't Open
My driver side back suicide door won't open. It is the top latch that is not disengaging. I think I heard something loose in that door over the past month. Am I going to have to take off the inside panel to fix it?
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: Extended Cab Driver Side Door Won't Open
I can't figure out the problem with my extended cab door. Driver's side doesn't open with either door handle.
View 13 RepliesFord 7.3L Power Stroke (1999-2003) :: How To Remove Driver Side Rear Rotor
I noticed my rear brake smoking on the truck really just the rear driver side. I had replaced the pads and caliper and rotor a very long time ago. What I think happened is the parking brake got hung up somehow. The wheel was extremely warm and the reason I noticed it was not only the smoke but I felt some sort of wobble or almost out of alignment issue.
When I got home I noticed the smoke and extreme heat. I removed the caliper and the pads look still "new" and evenly worn. I did bleed the caliper just to make sure no air, I even put a spacer in the caliper and my wife applied the brake and they closed appropriately. Then I was trying to get the rotor off and no success. I did adjust the parking brake but I am not sure if you move it up or down to loosen it up?
I have used PB Blaster to try and loosen it up, rubber mallet while I turn it (although it does not turn easily at all), I sprayed it inside where the adjuster is hoping it would seep down between the shoes and the hub. I heated the hub up with a little torch - no success. I was thinking of using a wood piece as a butter and hammer from the inside out on the rotor but fear that will warm the rotor itself.
Ford 7.3L Power Stroke (1999-2003) :: Driver Side Door Panel And Liner Off
I've taken the driver's door panel off, and unpeeled the liner. Now that the door is naked and exposed, I'd like to fix several things at once, rather than wearing the adhesive liner out by sticking and unsticking several cycles.
Here's a short list of some potential fixes I foresee taking care of while in there, how to :
1. The door ajar light. Mine went out over a decade ago, and the gallon of WD40 I sprayed into the latch did NOT fix it. In fact, it turned it from an intermittent issue into a permanent problem. I'd like to fix it now, as I miss having a light at night when the door is open. How do I fix it? Links, part numbers, tips, pictures, videos, search terms... all info welcome.
2. Bottom door rust. I don't really have much, but I see very faint hints of paint bubbling under the lower door weatherstrip barrier, which I have also removed. I've read about two schools of thought on preventative maintenance.
A. Pour oil or grease into the bottom of the door.
B. POR15 paint in the bottom of the door.
So basically, oil or paint? Obviously, one can't paint if one does oil, but on the other hand, some say that paint... especially thick paint like POR15, can actually do more harm than good by trapping moisture in the bottom pinch flange, or by creating craters or tunnels where water can burrow and then get trapped, rotting the metal away. What are your thoughts and experiences on this? I'd prefer a solution that minimizes the number of times I have to unstick the interior liner from the door.
3. I'm doubling the lower door weatherstrip with a combination of the older and newer designs. Ford sells the weatherstrip with clips attached, but neither those clips, nor the original clips, are really effective for what I'm trying to do. I've already done the rear doors, and made it work with the original clips, but they are brittle, and I lost a couple to breakage. Today, I broke three clips pulling the old weatherstrip off of the door.
I can't find these clips anywhere locally... I've tried every variety the auto parts and auto body stores sell, and Ford doesn't sell these clips separately from the weatherstrip... and even if Ford did, they OEM clips are not long enough to hold the double deployment of old and new styles of weatherstripping.
In searching this issue, it appears that a lot of people have broken these clips, which stands to reason with plastic in baking inside a hot door for 15 years. I'm sure I'm not the only one who would benefit from finding a good source of automotive clips.
4. Mirrors. I'm finally getting around to this, and this is what motivated the door panel removal in the first place. I need the dog bone harness that converts from a round connector to the flat style connector. Specifically, I need part numbers 1C3Z-14A411-AA and 1C3Z-14A411-BA. Ford didn't originally sell these dogbone harnesses separately, but included with the purchase of newer style outside rear view mirrors in case the translation harness was needed. Sometimes it was, sometimes it wasn't, so there would often be these unused harnesses left over.
5. Jimmy Jammers. Will they cause more harm than good? Does a better alternative exist? Thinking of installing these while I"m in there, but worried the door will be damaged worse as the thief tries to fight their way in. And, with body on shell doors, there appears to be much easier ways to break into an SD anyway, so part of me thinks, why bother
Ford 7.3L Power Stroke (1999-2003) :: Can't Undone Harness On Top Of Driver Side Valve?
I have what might be a big problem, the main harness on top of the drivers side valve cover I can't get undone, the bolt holding it together is stripped or the nut who knows? wondering if there is any way to take it apart otherwise.
View 11 RepliesFord 7.3L Power Stroke (1999-2003) :: Driver Side Brake Line Cut At Inner Fender
2003 Ford excursion 7.3. Above the drivers side front tire, the hard inner plastic made contact with the hard line above the frame.. Cut the line. I can't tell if this line is 1 piece towards the reservoir since its hidden from my quick inspection. Looking for a schematic on replacing this line?
This happened after my wife took the truck back to the sugar bush.. She must have been hitting jumps or something
Ford 7.3L Power Stroke (1999-2003) :: 2001 - No Power With Smoke Coming Out Tail Pipe
I would I have a 01 7.3 e350 with 111k miles. I drove the van a couple of days ago.it sat for 2 days and now it wont go past 30mph.the van shakes crazy and went when i hit the petal no power with smoke coming out the tail pipe sometimes. When I shut the van off and restart it to drive it,it sounds better. I changed the fuel filter with motorcraft and changed the oil. Here is the kicker. It ran good after I changed the fuel filter the whole day and now its 4th of july and I went to get some drinks and it happened again.
View 11 Replies