Ford 7.3L Power Stroke (1999-2003) :: Block Heater Plugged / Truck Crank But Won't Start - Fix?
When the block is cold my truck will not start. If i keep the block heater plugged in it will crank but is still a long start. I have tried just about everything i can think of and it is way too much to list so i will give as much info as i can.
New- gpr, glow plugs, HPOP, batteries, starter, fuses, valve cover harness/ injector and glow plug wiring, vacuum lines. I have checked out just about everything remotely possible.
Ford 7.3L Power Stroke (1999-2003) :: Long Cold Crank / Hot No Start
I have a early 99 f250 super duty 7.3l and it's giving me fits. about a month ago the truck started to do a hot no start. drove truck for about a hour. Shut it off and half hour later no start. Let it sit over night and would start with long crank.
Changed CPS no change. Pulled tuner and set back to stock. No change.
Changed fuel filter, no change.
After reading forums changed IPR and truck started and ran great. About a week ago back to the same problem. Battery's are about 2 months old. Oil change and oil filter a month ago.
Checked the hpop reservoir and its 1/2 from the top.
Checked fuel bowl and it has fuel. no sign of oil in it.
Drained bowl and watch bowl fill back up. seems to fill quickly.
Pulled passside valve cover to check for bad orings while cranking.
Every thing seems fine. have not done driver side yet. used FORSCAN and ran buzzed test on injectors and they all buzzed what seems to be about the same. ran test couple of times to make sure. this morning I ran a live scan while cranking and this is what I got right before it started. ICP 660.6psi, IPR 64.84% and RPMs 227. took 8.86 seconds to start. after work scaned again for hot no start and this what I got. ICP 292.9psi, IPR 55.86%. and RPMS 203. unplug ICP and no change. still will not start. one thing I did notice when plugging ICP back in I looked down in side at the pins and can see what seems to be bubbling around one of the pins. the pig tail has just the slights sign of oil.
Ford 7.3L Power Stroke (1999-2003) :: Repair Of High Oil Use And Long Crank?
Parts came from Riffraft Diesel Performance. A set of "o" rings for the injectors. High flow CVD fittings for the fuel lines. Turbo rebuild kit. (its got 210,000+ miles) Anti Surge compressor wheel.(ok its not part of the oil problem)
Photos to come. I will take during the rebuild.
Ford 7.3L Power Stroke (1999-2003) :: 2001 E350 - Long Crank Before Starting
I have a 2001 E-350 w/7.3. When I start the truck first thing or when engine is cooled down it starts fine. I checked the high pressure pump pressure and it is 500 - 600 psi start up great. But when engine warms and try to start it it has long crank before starting. I checked pressure and it is between 425 to0 450 and takes awhile for it to get to 500 or better. Is this a cause of the high pressure oil pump ? I changed the oil and still does same thing. Also I noticed that after engine is hot and I try to start it, while cranking the engine the oil gauge does not move. I don't know if it supposed to when you crank it or not. I thought on other 7.3's I've worked on that the gauge builds up pressure....
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: CEL On - Long Crank / Truck Starts Losing Power And Eventually Died
On the way to work, the truck seemed to have a miss at idle and the CE light came on. Long crank to start leaving work, and truck starts losing power and eventually died. No smoke while it was losing power. Towed it home and checked the fuel pump and lines for blockage and found nothing.
2003 7.3 F-250 430K miles
strong cranking but no start no smoke out exhaust
Oil changed recently
IPR changed
Both UVCH gaskets and pigtails have been repaired.
ICP sensor and harness changed, also disconnected no change in cranking.
fuel filter changed today (no oil in bowl)
3/4 tank of fuel
dash gauge for lpop goes up to normal range during cranking and oil light turns off.
WTS light comes on and turns off as normal
tach gauge moves up between 100-200 during cranking
fuel pump turns on and pressurizes system like normal and turns off.
Ordered AE for the truck, and it directed me to the passenger side bank high open. Fixed the harness on that side and still nothing.
Sent off the IDM and it passed with flying colors
So now i'm leaning towards the HPOP, but would hate to fork over the cash for it and still not get anywhere. I'm going to take the valve covers back off and check the discharge ports for the injectors tomorrow.
Ford 7.3L Power Stroke (1999-2003) :: F350 Running Rich / Crank Very Long Time Before It Starts
I recently (in the last few months) have noticed my truck (1999 F350 duallie) seeming to be running very rich … I pull a 32' trailer with it and noticed on the art few trips the front and right side of the trailer covered with diesel fuel spots when I got home …. It also smells very rich when idling…. The last couple times I started it in the mornings it seems to crank a very long time before it starts …it still runs but its got issues evidently … it has these 3 codes :
P1280
P0475
P1670
The 1670 will clear , but the other 2 I can't clear, they are right back every time you turn the key on …
Ford 6.0L Power Stroke Diesel :: 2003 - Cough / Sputter For A Few Minutes With No Power After Long Crank
So, a year ago or so I had the truck die on me, it would start after cranking it a long time and cough/sputter for a few minutes with no power. I thought it seemed like a weak hpop or leaking oring, so I tore it down and put it all back together with a something or other hpop. Now I have a no crank no fuel pump condition, the injectors don't cycle when I turn the key on, I do get relays clicking, but no start, the yellow/blue wire gets the starter to turn over, but no fuel, so couldn't start if it wanted to... I am getting 120 ohms (like 122) on the dlc 6,14 and millivolts, basically nothing between 4 and 14...
I sent the ficm off to get rebuilt and they told me that it was already good (charged me anyway though, ah well...) I wiggled wires around and pulled my ficm plugs apart and pushed the wires in some, didn't seem to move any... What is next? There can't be that many things that cause all three, No Fuel Pump, No Crank and No Injector Buzz, can there?
Ford 6.0L Power Stroke Diesel :: 2003 F350 - Intermittent Long Crank When Hot
2003 6.0 will fire within 2 seconds when cold, literally a "bump the key" and she fires up scenario. Recently and only when the engine is hot I'm getting extended crank times and sometimes it takes several attempts for the truck to start. I replaced the HPOP with an upgraded pump after the factory HPOP went out at 311,000 miles. I know this sounds like a standpipe leak scenario but it doesn't act up all the time, sometimes it fires right up even when its hot. my thinking is a leak is a leak and only gets worse.
My IPR is reading in the 26% range, FICM is steady in the 47.5 to 48 volt range and at idle 585 to 600 psi on the ICP with a good FICM sync. I'm going to to use my scan gauge and see if I can catch an extended crank scenario to see if the ICP is reaching 500 psi but is there somewhere else I should be looking? FICM relays possibly? I've noticed when i turn the key on I'll hear the fuel pump,vacuum pump but the clicking sound is very brief or nonexistent (not sure what the clicking noise is from I assumed glow plugs but its absence is noticed)...
Ford 7.3L Power Stroke (1999-2003) :: 2001 - OBDLink MX Plugged In Then Start Otherwise Won't?
My 2001 7.3L Diesel has 222,000 miles on it. Yesterday I shut it off at a drive through window, went to start it and it just cranked, no start. The engine light and the wait to start light did not come on. I plugged in a code reader this morning and when I turned the key I heard a buzz and a click, I noticed the engine light and the wait to start light came on. I cranked it over and it started right up, when I unplugged the code reader, it died. Plug it back in and it runs, dies every time I unplug it.
View 13 RepliesFord 7.3L Power Stroke (1999-2003) :: 2002 - Won't Crank And Start - Electrical Malfunction?
I have a 2002 F-250 with a 7.3.
I have been having a no crank, no start issue off and on for a while. batteries are new, cables are new, connections are clean, and starter has been rebuilt and checked. I bought a "starter relay" which i thought was the top solenoid in this picture. I also replaced the lower solenoid in the picture. The bottom solenoid was replaced with what im sure is the correct replacement. The upper I think is wrong. It started but then shut down and will not restart. The upper solenoid also was very hot after it shut down.
Long story short what is the upper solenoid for? Im assuming its not the starter solenoid. If so where is the Starter solenoid on a 2002 7.3?
Ford 7.3L Power Stroke (1999-2003) :: 2000 F350 Never Started When Temps Below 25 Unless Plugged In
My 00 F350 has never started when the temps were below 25 unless it was plugged in. This year is no different, but now it won't start when it's plugged in. It just turned 200K and I know things have to be checked, but I don't like doing them in the winter so I was hoping to make it through this winter and fix things. I needed to use the truck the other day so I plugged it in before I went to bed, It wouldn't start, so I got looking, crawled under the truck and the block around the heater was cold, checked the plug with an ohm meter and it showed that there was an open, so I checked the cord, sure enough there's a splice in it, with a broken wire, so I fix all three splices, check it again and it's still open, under the truck again, and find another splice at the end of the factory wire loom with a broke wire, got them replaced, got a good reading with the meter, and now I'm back in business, Plugged it in for a couple of hours, hit the key and it fired like it was new. Well not that good but it did start.
View 7 RepliesFord 7.3L Power Stroke (1999-2003) :: 2002 7.3L Will Crank Forever But No Start (bad Fuel Pump)
I just got delivered a 7.3L from down south. Batteries were dead so replaced both. Fuel was a couple notches above red line (much closer to red line than 1/4 tank) so I added about 7-8 gallons.
It will crank forever and ever...Won't start.
With starter fluid it starts but not strong enough to pump the pedal and rev it up to keep it idling.
I know s-fluid is bad but if I continuously spray with key turned forward it will run but as soon as I let go of key it shuts off.
20 degree weather and it was delivered to a parking lot so I cannot plug it in.
Was told to check filter cap, turn key, and see if it fills bowl with fuel....if not then it is fuel pump. Someone else mentioned that it could be bad crank position sensor? Does this sound like fuel pump?
Ford 7.3L Power Stroke (1999-2003) :: Truck Won't Fire After Glow Plug Replacement Unless Plugged In
I just replaced the glow plugs, gpr, valve cover gasket and harness. When cooled down, cranks but won't fire. Smoke DOES come out the tailpipe. If I plug it in for awhile it fires right up. What else can I do or check?
View 5 RepliesFord 6.0L Power Stroke Diesel :: Long Crank After Night Sit?
I'm having a long crank cold start issue. It takes about 2 five second cranks before the truck will start up. It just started acting this way yesterday before I fired it up to go to school. After its warm it fires up no problem the rest of the day, just takes a bump of the key.
I don't think it's the GP system as this truck has started at -20 to -25C all winter long unplugged with no issues. From my reading some sources say that it could be a HPOP leak, maybe dummy plugs?
Is there any way for me to do some more diagnosing - places to look or test for? There are no stored codes other than an EGR code due to the delete. Truck is completely stock with atlas 40.
Ford 6.0L Power Stroke Diesel :: How Long Is Extended Crank Time
So how long does one have to crank until it is considered an extended crank? 2 seconds, 5 seconds, 10 seconds.....?
The reason I ask is after all the motor work I did on my truck sometimes she fires up in less than 1 second of cranking and other times it take maybe 2 seconds of cranking. I do not think 2 seconds is considered and extended crank time but was just curious about what is considered extended cranking.
Ford 7.3L Power Stroke (1999-2003) :: Long Start After Sitting For 8 Days?
After setting up about 8 days, my truck has long start now. It starts but takes longer.
I plan to start with charging the batteries over night and see what happens. How old they are since I bought it last year. The batteries did drag just a tad when it started but seem to be back up after driving.
New ICP few months back. I have a couple scan tools.... Forscan and Dash Command. What to look for?
Last note: it starts fine, just takes longer now. Is plan to start tonight.
Ford 6.0L Power Stroke Diesel :: 2006 F350 - Long Crank Time
I have a 2006 F350. I have long crank times. No Codes. I have Autoenginuity with Enhanced Codes and everything shows fine. I replaces standpipe and dummy plugs. Glow Plugs and harness. I was hoping it not be the STC but I needed to do oil cooler so wanted to eliminate STC. Got truck apart and the STC Fitting is newer style so I'm kinda bummed out. Not sure if I'm missing something and as far as I have it torn down is there anyway to test what could be causing the problem? Or just put it back together and keep my fingers crossed that whoever put the new STC fitting in screwed it up. I'm beginning to not like my truck.
View 8 RepliesFord 6.0L Power Stroke Diesel :: 2005 - Long Crank And No Fire / Startup
OK here we go it all started with a long crank and now no fire. I changed cam sensor wiggled wires got to fire , shut off than nothing . Changed wire from cam sensor to about 6" from ecu found small nick in wire. Swapped ecu no good... I am getting my numbers from torque app.
ficm sync = 0
RPm = 172
FLP = 12
fmp =49
Hpop = 1823 max
Ipr = 80.9 max stready at 48
ipr volt =.02 at rest
Also tested fuel pressure at filter 80 psi ( blue spring)
ficm sent to ficm repair, tested good
cam sensor changed , pig tail also
bubble test on fuel filter no thing there
So any thing else to check or am i looking at a harness change?
Ford 6.0L Power Stroke Diesel :: 2005 F350 - Long Crank Times
So my recently purchased 2005 f350 has an abnormal long crank. I searched all the internet and everything pointed to STC fitting. Well I knew I had some other things I wanted to knock out so I ended up buying an update kit from sinister diesel. It included an updated fitting, new degas cap, updared turbo oil feed and return lines, blue spring update, and "dummy" tubes or something like that.
During the last few days I have removed the turbo, and finally got to the hpop. As I was removing the turbo I thought I might have the updated lines as there was no braided area in the feed tube. Sure enough I pulled the hpop and I have the one piece fitting. So now that I have wasted all this time removing all this stuff for no reason I still don't know what is causing my long crank. I am going to probably install the new fitting and lines anyway but where do I go from here?