Ford 7.3L Power Stroke (1999-2003) :: Installation Of Remote Start System?
I've been looking for a remote start system to install on my truck it has no remotes of any kind now. I've been googling most of the day and i can't seem to find anything except something that hooks to a edge tuner of some kind.
View 6 RepliesFord 7.3L Power Stroke (1999-2003) :: Installation Of Fuel Pressure Gauge?
I bought an Autometer 4763 gauge that didn't come with the correct fittings to plumb the sender into one of the extra ports on the back of the bowl. I went to the Ace hardware store right across the street and they didn't have anything (not surprised) and then Napa. They couldn't find a fitting to match either. He found that the plug threads are 7/16 20 tpi and the sender is 1/8" NPT. He suggested getting a 7/16 20tpi bolt, drilling it rifle-style, and then tapping it for a 1/8" NPT. The alternative, and what I ended up doing, was to use brass fittings to tee it off one of the supply lines to the heads. I ended up going that route but wanted to know if I should have looked harder for the right fitting.
Here's a pic of what I have now. I've test fit it, and it seems to work although I will need to insulate the hard lines because they rub due to the offset.
Ford 7.3L Power Stroke (1999-2003) :: Fuel Pressure Gauge Installation
Looking for pics of where/how they mounted their fuel pressure gauge? I'm getting ready to install one.
View 11 RepliesFord 7.3L Power Stroke (1999-2003) :: 2002 - After Super Chip Installation Got Icp Code?
I have an 2002 7.3 powerstroke. It has a super chips installed, set on heavy tow mode. When throttle is on the foot and I start up a hill check engine light comes on. Code is for icp fault or uncontrollable. Also happens on cruise but more often on the foot. Have to reset to get check engine light off. Light stays off til I go to pull a hill again. I am also pulling a horse trailer with 1-4 horses. Could the programmer be causing this?
View 4 RepliesFord 7.3L Power Stroke (1999-2003) :: Battery Lockout Perko Switch Installation?
Not near my truck at the time and wondering if I can install one of these switches. I don't know where the 2 positive battery cables meet.
View 6 RepliesFord 7.3L Power Stroke (1999-2003) :: Injector Installation - Torque Hold Down Bolts
I have been reading here about alternate methods to torquing the hold down bolts for the injectors. This winter I replaced my old stock split shots with new alliant single shots. I installed the injectors into a cold engine and torqued the hold down bolts to 10 ft lbs. I did not ever go back and re-tighten.
Is it suggested to go in and re-tighten the injector hold down bolts to 10 ft-lbs after the engine has been heated up and cooled down? What are some symptoms of a loose injector? I am imagining premature wear on the injector cups, low compression and maybe some mixing of oil into the combustion chamber.
Did just throw the injectors in and go back later to retorque only to find they were all fine or were some loose?
Ford 7.3L Power Stroke (1999-2003) :: 2002 - Engine Light On - Transmission Not Working?
so got to work today, truck engine light comes on all foward motion stops. Just coasts and idles along. I have 280k on the orig stock trans. I also have dp tuner and did the valve body upgrade along with adding the 6.0 cooler hoping to extend the life of the trans. Reverse works. So i asume I am needinf a new trans. My options are Ford HDr4100 orig 4100, Or BTS built trans. I also pull a toy hauler as well. My question is If I order the BTS can I have a my local shop install it or does it need to be programmed at the dealer. If I get the HD from ford installed will I have to remove the dp tuner chip to get it programmed and also will i need another new valve body replacement.
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: 2003 - Running Rough / 2 Cylinders Not Working Correctly
I have a 2003 F250 7.3L. I put new injectors in my truck four months ago and all of a sudden, I have 2 cylinders not working correctly, making the truck to run really badly. I sent the 2 injectors from the bad cylinders back for warranty and they replaced both of the injectors but nothing was wrong. I put them in and the truck still runs badly. I have a new fuel filter, new ICP, new CPS and glow plug relay. I cannot drive the truck, it smokes white at idle. I can unplug each injector at a time and cyclinder 5 does not change how the truck runs
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: Power Windows Stopped Working
Recently my power windows stopped working...sort of. Here's what I mean: If the drivers door is closed none of the windows will go down. However, if I open the drivers door halfway or all the way I can roll up/down all the windows. If the windows are down and the drivers door is closed I can, almost always, roll up the drivers window, however the other windows in the truck will usually not roll up. Open the door halfway and up they go.
A couple of other things I have noticed. When I press the down button for the drivers door window, with the door closed, I can hear the relay, under the dash, kick on and the window will move about a millimeter down then stop. Additionally, the courtesy light on the drivers door comes on while the door is closed. I haven't checked if the other courtesy lights come on at the same time.
Hopefully my explanation is understandable. I would love to solve this issue. Getting tired of opening the door to roll down the windows. Plus when there's a fly in the truck and I'm driving I can't get it out.
Ford 7.3L Power Stroke (1999-2003) :: Power Steering Only Working When Turn It To The Left
My power steering is only working when i turn it to the left. When I turn it to the right i have to get a 1/4 of a turn in until the power steering takes over. So i get under my truck to discover what seems to be a piece of my tranny missing. How screwed am I ???
View 11 RepliesFord 7.3L Power Stroke (1999-2003) :: Power Windows And Radio Quit Working
On my 2003 powersteering the windows and radio will just quit working. Then they will come on again. Maybe in and hour or a day or a week. Where do I sart.
View 6 RepliesFord 7.3L Power Stroke (1999-2003) :: 4WD Not Working?
Four wheel drive not working?
View 2 RepliesFord 7.3L Power Stroke (1999-2003) :: Power Stroke Malfunction - In Reverse / With Lights On Engine Shut Off
Last November I forgot to plug my truck in and it got down to 0, my girlfriend tried unsuccessfully to jump start it. When I got home I jumped it and got it running. I took it down to a heated shop to troubleshoot the glow plug circuit. I discovered it was not getting 12v to the glow plug relay. Also I started it and tried to back it up in the shop, when put in reverse it killed the engine, not lugged it down it was like you shut the switch off.
Also I discovered if you turn the lights on it kills the engine immediately. It will not crank with the lights on either. So far I have replaced the computer,ignition switch,batteries, and cam positioning sensor. Now comes the weird part!! I decided to get it running and pull the bulbs out of the back up lights I pulled the drivers bulb first then the passengers side bulb. When I pulled the passengers side bulb it killed the engine.
It is not my daily driver so it still sits in my shop. I have a hunch it's a ground issue but I've checked and cleaned up all the grounds I can find and it still has the problem.
Ford 7.3L Power Stroke (1999-2003) :: F350 - AC Not Working Right
I have a 99 f350 Lariat. I was wondering if there is such thing as a cabin air filter on these trucks my a/c is blowing and its cold just not blowing hard enough like it used to if there is not a cabin filter is there a way to clean the evap coil. I always figured youd have to after so long since you always got dirt and what not in the truck the coil should stop up after so long its got to happen but how hard would it be to clean it?
View 7 RepliesFord 7.3L Power Stroke (1999-2003) :: Cam Sensor Won't Working?
i have a 99 f250 7.3 powerstroke. the cam sensor was acting up. that what the scan tool said. i replaced the cam position sensor yesterday, and the truck is still acting up. the motor hitches and will shut off randomly. it tripped the check engine light, and the code is the "cam position sensor" once the truck is warmed up and shut down for like 10 minutes the sensor will not act up anymore. if i just start the truck and run it, even once it is up to tempature it will act up. but if i shut the truck down for about 10 minutes, it goes away. is there something else that could be causing this?
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: OD Switch Not Working / No First Or Second Gear
I have an early 99 f350. when i got the truck the OD switch(maybe light too) didn't work. i ran it for about 1k mi. yesterday i left work to come home and i didn't have 1st or 2nd gear but still had 3rd and od. the only way to get 2nd is to manually put it in 2nd gear. 1st seems to be nowhere around.
I do not have a code reader and wont for at least a month or so. I did install a simple ts6 in it, that's about all i did with the truck.
Ford 7.3L Power Stroke (1999-2003) :: Running Lights Not Working
A little background information is that I was towing a large gooseneck trailer about a year ago when half way to the destination the lights quit. Not just the trailer but the truck tail lights, turn signals and everything except the headlights. Well after getting there and unplugging everything it stayed the same. Well on the way home without the trailer the lights began working again. All the truck lights acted as it never happened. No blown fuses or anything.
Well things are are going ok since then but I can never get running lights to any of my 3 trailers to work. Turns and brake lights are fine. What gives? All the fuses are fine and the truck running lights work just fine. One thing I have noticed is that on my horse trailer I have the little led lights on the sides operational... I would have assumed these to be the same as the tail running lights.
Ford 7.3L Power Stroke (1999-2003) :: 2001 F250 - 4x4 Not Working
I have a 01 f-250 7.3 6 speed. I bought the truck a few days ago and the 4x4 wasn't working the dealer replaced the transfer case motor. I have another 01 f-250 that i have been switching parts out of to see if that makes a differences and found nothing to work. Ive switched the switch on the dash out and nothing. Ive switched the two relays under the hood and nothing. I have also checked all fuses. and the connectors on the transfer case.
So I finally popped the covers off the two relays and squeezed them with my fingers and boom transfer case locked into 4lo and then i can squeezed the other and boom back in 2h! So now I'm lost, I know the wiring from the relays to the transfer case is good and the switch is good and relays are good so I'm at a loss.. Also cruise control isn't working idk if that could be related i don't think it is but idk?
Ford 7.3L Power Stroke (1999-2003) :: OBDII Port Not Working- Fix?
I plugged in my basic OBDII scanner but I'm getting nothing back (the scanner works on my car so it's not the scanner). This is inline with the transmission shop where they said they couldn't connect either to my truck. But now the question is: now what? I don't think there is a fuse or such but how to troubleshoot the port.
Oh, and no, the CEL is not illuminated, just the ABS light remaining on from when my 4R100 was replaced a couple weeks ago. Can't connect to diagnose.