Ford 7.3L Power Stroke (1999-2003) :: Hub And Wheel Bearing Replacement
I'm in the middle of replacing the hub and bearing assembly, once i got the hub assembly off, I noticed when I grab the axle there is a lot of play if I pull the axle up and down or left to right. Is this normal as the hub assembly holds it in position? I don't have any fluid leaking so the seal must be good, or am I missing something. I am trying to do this in 30 degree weather and it sucks.
View 10 RepliesFord 7.3L Power Stroke (1999-2003) :: Passenger Side Wheel Bearing Is Going Out
My passenger side wheel bearing is going out. I had a local company replace it under extended warranty 7 years and 90k miles back. I think I have gotten pretty good life out of it. I think it was from Napa but not positive. I try to grease then once a year but I'm not always successful.
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: Replacing Front Wheel Bearing Hubs?
I was getting a growl/grinding noise from my front hubs (driver's side I think) when I do a slight right turn like going around a curve, not turning around a corner. Just started happening the last week after returning from a 4th of July roadtrip. First thought was wheel bearings going out and started reading up on the forum here to see what was needed. Last night, I started getting a continuous growl when I was 5 miles from the house so just pulled up and parked it. I'm assuming (without pulling anything apart), it's the bearing assembly and I can get the Timken version at Autozone locally.
The problem is I generally do my heavy maintenance at our family shop in San Antonio but I live in Austin so will need to do this in my driveway. I have all the basic tools, just need to know how involved it is to do in a driveway instead of a shop. Thoughts?
Ford 7.3L Power Stroke (1999-2003) :: After O Ring Changed Bleeding Off Air?
I'm sure there is something on this somewhere but can't seem to find. Getting ready to change injector o rings and see where people say to drive it 200 miles to get it running right again. Well, I am in the process of a conversion and have no tags or insurance on the truck. Trying to fix issues before I spend that money on it because don't know how much I am going to have to put in it to fix the issue's.
Is there a way to bleed out the air so I don't have to drive it 200 miles? Also, how long will it smoke after the injector change to see if it is actually fixed? I know I should probably see a big difference is ICP,IPR and such. Already know it has leaks in the turbo up pipes which will have to be dealt with too.
Ford 7.3L Power Stroke (1999-2003) :: Changed Injectors / Cannot Even Get Engine To Crank?
I changed my injectors and glow plugs on passenger side. I tried to start the engine and it wont crank (turn over). I tried to turn over by hand by turning alternator bolt counter clockwise, turns a little bit and then get very difficult. Is this hydro lock? I stuck a suction tube down injector holes and made it to the piston not much oil came out, I think the truck was a little low on oil before I started the project. The starter wont turn the engine over. I even turned the engine over by hand many times before I put glow plugs in to evacuate the cylinders. I don't know what to do?
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: 2000 - Changed Alternator Still Overcharging
I am having an overcharging issue with my 2000 F350 diesel. It first started when I had a garage check the batteries due to poor starting this winter. They found one reading 6V and I had them replace it. After that the battery light came on. So I had them check it out again and they replaced the other battery. I can't remember if it started before or after the second battery but it started overcharging 16-17 volts according to the dash. I replaced the alternator still overcharging. Since then I have run a 4ga ground from one battery to the alternator and a 4ga ground wire from the other battery to the cab. I also checked most of the stock ground wires which all seem fine. Lastly, I also bought a ford alternator pigtail because one of the wires had cracked insulation and some corrosion. Currently it overcharges unless the battery light comes on which once it does the voltmeter in dash reads normal.
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: Replacing Needle Bearing In Hub?
I need to replace the needle bearing in one of my hubs. I was wondering if the bearing needs pressed in or can it be hammered in with a large socket and a hammer?
View 2 RepliesFord 7.3L Power Stroke (1999-2003) :: Axle Bearing And Hub Assembly Replacement
It's time to replace my axle bearing and hub assembly. Looking at RiffRaff site they show 3 different models. Early 99, fine course and course. I think I have the course thread but just want to make sure before I order. My truck is a L99 and I don't have the abs sensor. Looks like all 3 have come with the abs sensor. Do I simply not connect the sensor? Here's a pic of what i have. Course thread?
View 3 RepliesFord 7.3L Power Stroke (1999-2003) :: 2001 - Changed UV Harness / OD Flashing But Running Great?
Had to change the UVC harness on my 2001 7.3. Truck fell out. Trailered it home and changed the UVC harness on the passenger side. Truck is running great, but now the OD light is flashing. Can't read transmission codes, but was wondering if something from the bad harness could have caused this? Any thoughts?
View 7 RepliesFord 7.3L Power Stroke (1999-2003) :: 2000 VSS E350 Short Bus - Changed Sensor But No Input AE?
I have a 2000 Ford E350 Short Bus 7.3 It has abs in the rear diff. I have changed the sensor. I have connected my AE but get nothing at all from the sensor. My speedometer does work. My overdrive light flashes and the transmission does shift properly. I plan on looking for a bad ground. Can I test the wiring using a volt meter
View 2 RepliesFord 7.3L Power Stroke (1999-2003) :: 2001 F250 - Front Bearing Assembly
2001, F250, 4x4, 432,000 miles...
Seems this truck eats up bearing assemblies. Its like every 2-3 years, I'm having to replace one side or the other. And we talking like 30-40,000 miles....
BTW.... although I'm not out doing much 4x4 driving, this truck does do a lot of dirt roads, probably over 50%...
Ford 7.3L Power Stroke (1999-2003) :: Changed Intercooler Boots Still Poor Boost - Turbo Dead?
ive noticed my boost has been going down lately. At first I thought it was a boost leak so I replaced all the intercooler boots and both sides of the intercooler pipes. That diddnt change anything at all. I recently got new injectors (200/30%) and a hydra tune for them and it was quick the first few days i was running with that setup, my boost has been dropping and currently at WOT I can't even get to 10lbs of boost and it is noticeable driving, it's slower than it was stock. There was no play in the shaft of my turbo and the turbo in there is only 2 years old. Could the turbo be bad already? Or is there anything else I can check before buying a new one. I have an upgraded hpop and the 6637 intake.
View 13 RepliesFord 7.3L Power Stroke (1999-2003) :: 2000 - Knocking Noise - Cracked Piston / Rod Bearing?
Chasing this knock and I'm starting to get a little bit worried. So I'm looking for what I should do next.
Here is the truck info... 2000 F250 4x4 206k. . Swamps Diesel 200/30's. Terminator HPOP. GTP38R. EBPV delete pedestal. Banks wastegate. AFE stage 2 intake. RiffRaff FRX. 4" exhaust. Hydra chip. John Wood Auto. 6.0 Trans cooler.
I have a knock sound coming from the area of #8. It is noticeably louder in that area with a stethoscope. Its not any louder anywhere else (oil pan, block, otherside of engine, or front). Truck does not smoke and runs and idles great otherwise. Was thinking possibly the cackle/fuel knock issue these trucks have but with bigger injectors and the FRX could this even still be a possibility?! Anyways here is what I've done.
Checked fuel pressure and at idle it is 61/62 with any tune. At WOT on Econ tune it goes down to ~40ish psi. With the extreme tune WOT dived down to 28/29psi. So my thinking was maybe that injector got screwed up so...
Swapped #8 injector with #2 so the front injector with the back to see if either it had some bad o rings or isolate the injector as the problem if the noise moved cylinders with the injector. While I did this I put brand new O-Rings on those two injectors and popped them in. Got it fired up and the knock is still in #8.
Unplugging the injector with the engine running the noise seems to disappear. HOWEVER, when I use the stethoscope the knocking noise still sounds like it's there but very faint. Without the stethoscope I can't hear it. Also driving the truck down the freeway and letting it coast the noise goes away when the injectors get cut off.
Recently pulled off valve cover and checked the pushrods and rockers on #8 and all looked fine. At this point I'm thinking wrist pin, rod bearing or cracked piston??? Could it somehow still be a fuel knock?
Ford 7.3L Power Stroke (1999-2003) :: Light Metal Rubbing Noise Coming From Front Left Wheel
I have developed a sounds that sounds like metal on metal. Not a grinding but more of a "swish swish swish" light metal rubbing when the truck has been running a mile or two. I can barely hear it over the radio but its very noticeable when the window is down. It is not affected by the pressing the brakes and it gets louder and faster in direct portion to speed. It will occasionally leave and start right back up. I touched the front rim around the hub and it was hotter than I wanted to hold onto. It didn't burn but it was hot. It was 105 degrees that day. Here is what I have done.
I replaced that front hub in 2010 and probably have 50K miles on it. I did the 3-9 test and there was no noticeable play. I spun the hub and while it seems to spin ok it does seem a little dry.... I will pull it tomorrow and see what it looks like.
I pulled the calipers off and the brakes pads are at half way and there is no burnt smell. I spun the rotor and it seemed flat and straight. I do have a small tiny lip all the way around them on both sides but I figured that's normal with 265K. I pulled the pins and they were dry but they didn't seem to be sticking. I cleaned them up with the boots and am going to replace them when I get some brake grease tomorrow. I have not looked real hard at the caliper but I plan on pressing that with a C-Clamp tomorrow to check it. Since the rotors and pads looked OK, I assumed there was not a stuck caliper although haven't ruled it out. The axle behind the hub seem to spin freely before I removed all this stuff and the hubs are not locked.
I think I covered it all .. I also thought it could be a rock or stick but nothing came out of my caliper or rotor when I took them off ..
Ford 6.7L Power Stroke Diesel :: Wheel Bearing Gone Out - Making Noise?
Wheel bearing go out? My left front just starting making noise and when turned by hand you can hear the bearings are shot. Called around this morning and with my luck its on back order and the entire hub has to be replaced since the bearing is built into the hub.
Anyways, I was wondering replacing this unit themselves and how long it took to complete? I was going to let Ford do the work but I figured I have never done a job like this and wanted to give it a try and looking at some Youtube videos on older vehicles it did not look that difficult.
If I find that its not difficult I will tackle the other side as well since I figure it is probably not long before that side is gone also and I would not want that to fail while I am out towing somewhere.
Ford 7.3L Power Stroke (1999-2003) :: Leaking Power Steering Under The Wheel Arch On The Driver Side
Initially had indications of a leak under the wheel arch on the drivers side.
About 3-4 months back replaced both PS lines and the leak stopped - briefly (maybe a couple a weeks).
Now the leak is back, but what's interesting is I lose more ATF fluid on a single long haul run than I do running round town for 3 weeks. I can't work out where the leak is coming from to identify what else to replace - short of just buying a pump and reservoir and replacing them as I've already done the hoses.
My turbo cooler pipe was hard up against the old PS pipe where it entered the side of the reservoir until I did the replacement hoses. Now I have it out the way but I'm wondering if it's caused some unseen wear or damage.
If I just do the pump to see if that works are the reman units any good out of Autozone or O'reilly's?
Ford Super Duty (1999-2016) :: 2003 F350 - Front Driver Side Wheel Bearing Went Out
I have a 2003 F350 srw 6.0. 4x4. Front driver side wheel bearing went out. Went to the auto parts store got a replacement. Got it all tore apart, put the new one on and the lockout didn't seem to fit right. Is there a difference in wheel bearing assemblies for electronic shift on the fly and regular lockout? I have the electronic shift on the fly lockouts and it had just a little bit of play in it when I put the snap ring back in.
View 3 RepliesFord Super Duty (1999-2016) :: 2003 F250 - Replace The Front Hub Wheel Bearing Assemblies?
I am needing to replace the front hub wheel bearing assemblies on my 03 F250 4x4. I know Ford changed the studs from coarse thread to fine thread in between the 02 and 03 model years. Mine has a build date of 08/02 and I haven't been able to find the exact date they switched over. I'm ordering the parts online and want to get it right the first time.
View 3 RepliesFord 7.3L Power Stroke (1999-2003) :: F350 Lost Power - Fuse Panel Under Steering Wheel Shorting Out
So I have a 1999.5 F350 diesel and the fuse panel under the steering wheel is acting up. I was driving my truck home the other night and I lost power and my truck shut off. I have had a problem in the past with the #30- 30 amp fuse ( controls the PCM and glow plugs from my understanding) that is under the steering wheel, I replaced the fuse and everything started working normally again. Until the other night when my truck shut off, so I replaced the fuse the truck drove again for 20 feet died again, I was able to hold the #30 fuse and allow my truck to start up again but would eventually killed the PCM and shut off again and would not start up due to what I believe the fuse location shorting it out and killing the power to the PCM preventing me from starting it up again.
I had my truck towed home and charged the battery and it started up fine the next morning. If I push on the #30 fuse my truck the shorts out and kills the power, I do not know if this is normal? The fuse is sitting loose in the fuse holder is there anyway making it fit tighter to prevent it from being so loose? I have read every other post online about the problems and tried everything they have recommended but still can not figure out what was wrong with my truck. I disconnected the fuel filter heater, and also the wastegate solenoid to see if that would prevent the truck from shorting out if I pushed the fuse it did not work.
What the problem could be causing the #30 - 30 amp fuse to be shorting out preventing everything from working? Or how to test the fuse panel and all the relays?