Ford 7.3L Power Stroke (1999-2003) :: Replacing Front Wheel Bearing Hubs?
I was getting a growl/grinding noise from my front hubs (driver's side I think) when I do a slight right turn like going around a curve, not turning around a corner. Just started happening the last week after returning from a 4th of July roadtrip. First thought was wheel bearings going out and started reading up on the forum here to see what was needed. Last night, I started getting a continuous growl when I was 5 miles from the house so just pulled up and parked it. I'm assuming (without pulling anything apart), it's the bearing assembly and I can get the Timken version at Autozone locally.
The problem is I generally do my heavy maintenance at our family shop in San Antonio but I live in Austin so will need to do this in my driveway. I have all the basic tools, just need to know how involved it is to do in a driveway instead of a shop. Thoughts?
Ford 7.3L Power Stroke (1999-2003) :: Hub And Wheel Bearing Replacement
I'm in the middle of replacing the hub and bearing assembly, once i got the hub assembly off, I noticed when I grab the axle there is a lot of play if I pull the axle up and down or left to right. Is this normal as the hub assembly holds it in position? I don't have any fluid leaking so the seal must be good, or am I missing something. I am trying to do this in 30 degree weather and it sucks.
View 10 RepliesFord 7.3L Power Stroke (1999-2003) :: Passenger Side Wheel Bearing Is Going Out
My passenger side wheel bearing is going out. I had a local company replace it under extended warranty 7 years and 90k miles back. I think I have gotten pretty good life out of it. I think it was from Napa but not positive. I try to grease then once a year but I'm not always successful.
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: Changed Wheel Bearing Now ABS Light Is On
As soon as I stepped on the brake and started to move backwards out of the garage, pedal pulsed and ABS light came on. Now it comes on shortly after starting and stepping on the brakes. I just finished the drivers side wheel bearing, u-joint, brake pads, rotors, outer axle stub, and all "outer axles" seals replacement.
AllAboutMPG offered a suggestion about shims on the sensor and checking the ring (never done this, figure it out when I'm there later today?) I figured I'd put this here for some additional input and (hopefully!) later be a good search source and fix for fellow members
Here is the original thread. I installed a Timken complete wheel hub unit with new sensor already installed on the hub.
[URL] ....
Ford 7.3L Power Stroke (1999-2003) :: Axle Bearing And Hub Assembly Replacement
It's time to replace my axle bearing and hub assembly. Looking at RiffRaff site they show 3 different models. Early 99, fine course and course. I think I have the course thread but just want to make sure before I order. My truck is a L99 and I don't have the abs sensor. Looks like all 3 have come with the abs sensor. Do I simply not connect the sensor? Here's a pic of what i have. Course thread?
View 3 RepliesFord 7.3L Power Stroke (1999-2003) :: Replacing Injector Cup?
im in the process of replacing the injector cups and i knew this would happen since the whole process went way to easy up until this part. I am using Clays remover kit and it will not remove the cup. I do it according to the book and it just keeps popping out of the cup when i try to remove
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: Replacing Steering Box?
The next thing on my list of things to replace on my truck is the steering box. I have dealt with a lot of play on my steering for quite a while. I recently replaced the the ball joints and that worked but I think the box is just worn out. I have read all the great review on Redhead boxes but I just can't afford it now. What else is out there? Is our oem box a motorcraft or something else?
View 6 RepliesFord 7.3L Power Stroke (1999-2003) :: 2001 F250 - Front Bearing Assembly
2001, F250, 4x4, 432,000 miles...
Seems this truck eats up bearing assemblies. Its like every 2-3 years, I'm having to replace one side or the other. And we talking like 30-40,000 miles....
BTW.... although I'm not out doing much 4x4 driving, this truck does do a lot of dirt roads, probably over 50%...
Ford 7.3L Power Stroke (1999-2003) :: 2001 - Replacing Injector?
I have an 01 F-250 Powerstroke. It has been shaking terribly at around 1500 rpms and shutters while holding the brake and increasing engine speed. I took it to the dealer and they told me that my #1 injector is bad. I decided to check around a little bit. I found a diesel service dealer that has brand new injectors. (Not rebuilts). Anyway I would like to attempt to install this injector myself.
1. Which injector is #1? (I've done a lot of mechanic work but not a whole lot on engines.)
2. What do you do with the fuel and oil that get into the cylinder? Do you have to get it sucked out?
3. Anything else that is crucial? What do you have to torque the injector bolt to?
Ford 7.3L Power Stroke (1999-2003) :: Replacing Pedestal O-Rings?
My 1999 F-350 7.3 is leaking from the turbo pedestool o-rings, from what my mechanic tells me. I would like to do this myself as it does not seem overly hard. This is my first diesel truck and am not quit sure how to do it. Looking for instructions or pointers on the process? I am a decent mechanic, but just have no clue on diesel engines and hoping to learn.
View 7 RepliesFord 7.3L Power Stroke (1999-2003) :: Replacing EBP Tube And Sensor?
I am doing some maintenance and trying to replace my EBP tube and sensor. I luckily have the dual alternator package, so getting the tube in and out has been a pain to say the least. I can't for the life of me get the tube back into place. As always, a 20 minute job is taking me 2 days.
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: Replacing Injectors - Which Injector Goes Where
I just bought a 99 F350 with 240k miles on it and got it for a deal because it needed injectors. Ive done the same job to my 97 OBS powerstroke. The injectors were already pulled so I had them sent for rebuild, the problem is I cant tell which injector goes where. is there a trick to figuring out where each injector goes when I put it back together?
View 4 RepliesFord 7.3L Power Stroke (1999-2003) :: 2000 - Knocking Noise - Cracked Piston / Rod Bearing?
Chasing this knock and I'm starting to get a little bit worried. So I'm looking for what I should do next.
Here is the truck info... 2000 F250 4x4 206k. . Swamps Diesel 200/30's. Terminator HPOP. GTP38R. EBPV delete pedestal. Banks wastegate. AFE stage 2 intake. RiffRaff FRX. 4" exhaust. Hydra chip. John Wood Auto. 6.0 Trans cooler.
I have a knock sound coming from the area of #8. It is noticeably louder in that area with a stethoscope. Its not any louder anywhere else (oil pan, block, otherside of engine, or front). Truck does not smoke and runs and idles great otherwise. Was thinking possibly the cackle/fuel knock issue these trucks have but with bigger injectors and the FRX could this even still be a possibility?! Anyways here is what I've done.
Checked fuel pressure and at idle it is 61/62 with any tune. At WOT on Econ tune it goes down to ~40ish psi. With the extreme tune WOT dived down to 28/29psi. So my thinking was maybe that injector got screwed up so...
Swapped #8 injector with #2 so the front injector with the back to see if either it had some bad o rings or isolate the injector as the problem if the noise moved cylinders with the injector. While I did this I put brand new O-Rings on those two injectors and popped them in. Got it fired up and the knock is still in #8.
Unplugging the injector with the engine running the noise seems to disappear. HOWEVER, when I use the stethoscope the knocking noise still sounds like it's there but very faint. Without the stethoscope I can't hear it. Also driving the truck down the freeway and letting it coast the noise goes away when the injectors get cut off.
Recently pulled off valve cover and checked the pushrods and rockers on #8 and all looked fine. At this point I'm thinking wrist pin, rod bearing or cracked piston??? Could it somehow still be a fuel knock?
Ford 7.3L Power Stroke (1999-2003) :: Replacing Field Coil On A/C Compressor?
I have a 1999 F-250 SuperDuty with a 7.3L. I need to replace the field coil on my AC compressor due to a broken connector (long story). After I remove the belt and compressor clutch, what is the next step to get the pulley off so that I can then replace the field coil? I am a computer geek by trade so I need clear steps. I looked on youtube, but all I found was how to adjust or replace the compressor clutch or the entire compressor.
View 3 RepliesFord 7.3L Power Stroke (1999-2003) :: Replacing Front Leaf Springs?
I tried to replace the rear spring bushing of the drivers side front leaf spring.
Got the nutz off the shackle... The lower bolt was bumping into the front drive shaft and would not come out all the way.
Biggest problem I was having seemed to be I could not get the axle to drop far enough to release the pressure on the bolts in the shackle.
NOTE: I was trying to do this without unbolting the U-Bolts from the axle.
I was under the impression you could do this without unbolting the u-bolts. I have all new hyperflex suspension bushings and would like to get them on.
Ford 7.3L Power Stroke (1999-2003) :: Battery Light On Intermittently After Replacing Alternator?
Alternator locked up in a parking lot. Replaced it and had to replace pigtail due to a loose wire in the harness. Now battery light comes on intermittently. New alternator is doing fine producing anywhere from 13.9v to. 14.4v. No output voltage correlation to battery light at all. The belt is still in great shape so I don't suspect slipping. Fortunately I caught the old one locking up almost immediately and had recently replaced the belt. Output voltage looks great. Are there any fuses for alternator?
Only thing I can think of that I did...when splicing in the pigtail that connects to the alternator, I briefly grounded whatever wire in the pigtail is hot. Was just a split second, but enough to see a spark and maybe enough to blow a fuse? I've seen people reference an "under hood" fuse box, but I don't seem to have one. My truck is a 2002 CC with just over 100k on the clock.
Ford 7.3L Power Stroke (1999-2003) :: 2002 - Replacing Clutch Master Cylinder
I am looking for a how to vid or resource on doing the job right. I purchased the complete replacement master cylinder from Napa. 2002 7.3 Powerstroke
View 3 RepliesFord 7.3L Power Stroke (1999-2003) :: 2001 - Replacing Door Handle Rod Lock Clip?
Trying to replace a right rear door handle on my 01 7.3. Attached is a photo of the new handle with the unlock rod. Also is attached is photos of the door without handle. I pointed to the part that moves the lack to unlock.
Looking for the clip part number or photo that is missing. I thought a hose clamp would work maybe with a nut on the rod?
Ford 7.3L Power Stroke (1999-2003) :: Replacing Electric Lock On Passenger Rear Door On Crew Cab
I have search youtube and only found front door lock replacement but not the rear..
How do you go about removing the bad rear passenger side door lock actuator ??