Ford 6.7L Power Stroke Diesel :: Message Center Buttons Not Working
A couple of weeks ago, had a weird thing happen. When turning left at slow speed there was a click sound that came from the upper part of the steering column (similar to the sound you got with the indicators on in the old super duties when turning and it would go over the clockspring). It hasn't repeated the noise since.
Anyways, a week or so after this, I happened to try to use the buttons for my message center to reset my odo, which I rarely use. Didn't work. In fact all of the 5 buttons associated with the message center on the left side of my steering wheel are not working, but the cruise control buttons are. The buttons on the right side of the steering wheel are also working fine.
I am not sure if the noise in the steering column is related (but it has me suspicious...), or just coincidental, but wondered on peoples thoughts to diagnose. I pulled off the cover over the steering column, all the wires in and out of the clock spring look fine, I haven't pulled the switch yet (need to look at the service manual to make sure I don't break it as I do it), but wanted to see what was the diagnosis.
Ford 6.7L Power Stroke Diesel :: How To Clear Message Center Warnings
Dealer forgot to reset oil life warning oil change. I cleared it in the "settings" but then "oil filter" and "fuel filter" warnings came in and won't clear. How do I get rid of them?
View 3 RepliesFord 6.7L Power Stroke Diesel :: Decreased Power Message Across The Dash Info Center
Got a Decreased Power message across the dash info center today and was limited to only around 5lbs boost. I stopped and pulled the codes and here is what I found:
P054E - Fuel Quantity lower than expected
P1249
P1247
P0471 - Exhaust pressure sensor range/performance
P02D7 - Injector learning @ max
P0402 - EGR flow excessive detected
I dumped the trailer and limped home to change the fuel filters. I could only go 35mph on the flats and 10mph on any kind of up hill slope. I switched out the filters, purged the air, fired her up and cleared the codes, all seemed well. I backed out and went for a test lap around the neighborhood, as soon as I turned the corner and rolled on the throttle and reached 35 the message came back and the codes returned. I will be towing it in to the dealer tomorrow for diagnostics.
Ford 6.7L Power Stroke Diesel :: Message Center Says Check Coolant Additive
I called my servicing dealer and he was unaware of the message or how to check/test this. He also did not think it was a warranty issue.
View 14 RepliesFord 6.7L Power Stroke Diesel :: 2016 - Got Low Fuel Pressure Message?
I have a 2016 F350 i purchased about a year ago and now has 7500 miles. last night it tossed up a low fuel pressure message and then de-rated then wouldn't start, i heard a crazy humming sound before it shut off. they pulled the fuel filters "claimed it was gelled" even though it fired right up once it got to the dealership. the fuel i run is good to -9*F and i use ford anti-gel on top of that. So they changed the filters and it wouldn't start again. now they are dropping the tank. So, I am not sure what they are gonna find but I am meticulous when it comes to pulling all the foil off of the anti-gel bottle before even opening the cap. I don't know what could possibly be in the tank to cause the issue.
View 13 RepliesFord 6.7L Power Stroke Diesel :: Got Warning Message - Low Fuel Pressure?
Driving back from the funeral and get a Low Fuel Pressure Warning message PPP up in the info display. No CEL's etc thrown (yet?). I have PM23A anti-gel in the tank already but stopped for diesels no poured more in. At the same time, I hear what sounds like an electronic motor making a whirring noise in the dash around the area of the under-hood fuel filter. Also sounds like there is the same noise from the back fuel pump. I assume it's the fuel system starving? Calling the dealer now, but going to continue pressing on cautiously until the truck tells me otherwise.
View 14 RepliesFord 6.7L Power Stroke Diesel :: Leaking - Oil Spray Going Down The Center Of Truck
So I just changed the oil on my truck I had a ford motorcraft filter on there and replaced it with a Fram filter ( only because that's what was on the shelf at the big W store ) I drove it to town and back once ( 35 miles round trip ) ...
I was going to add a trickle charger to my truck as It will be sitting for a while and I was laying under the front of the truck trying to fish the power cord down and I looked back and see I had Oil spray going down the center of my truck . So I thought dam my filters not tight as when I looked at it , had oil streaks coming down it. So I checked it was tight , would not move.
So I wiped if off with a rag and it looks to me as if the filter is leaking at the top seam . were the filter is crimped . There's not way I can take it off and take it back to the store. a filter that is oil soaked . I am going to replace it but before I do I am going to see if I can get the leak on video
Ford 6.0L Power Stroke Diesel :: 2005 F250 - Message Center In Gauge Cluster Only Show Mileage And Engine Hours
2005 6.0L F250 Lariat. I picked up a couple weeks ago. The message center in the gauge cluster will only show my mileage (kilometres) and engine hours but nothing else.
Also the three buttons/controls to the right of the steering column don't do anything. I checked the wiring behind the dash and it's all plugged in... The other problem is the SRS light will flash on and off while driving.
Ford 6.7L Power Stroke Diesel :: Reduced Engine Power Message Came Up On Dash And Truck Died
2015 F350 6.7L, 43,000miles
My family and I were driving into West Virginia this morning when the reduced engine power message came up on the dash and the truck died. I coasted off to the side of the road as best I could and got out. Immediately I smell diesel fuel. I look under the truck and there is fuel all over the passengers side frame and when I keyed it back up fuel started spraying down by the right front wheel.
Pulled the fender liner back and saw a small rubber hose that looks like it came off of a tee fitting down by the egr components. I tried to get it back on but wasn't able to get it seated 100% and when I tried to restart it blew off again. Truck is completely stock and ran perfect right up until it died.
Ford 6.7L Power Stroke Diesel :: Truck Quit - Stop Safely Now Message And Won't Crank
Luckily I was sitting in the driveway. Pulled the truck out of the garage. It started fine, idled fine, did not make as much noise as I was expecting but was warmer in the garage than outside. Stopped in front of the garage door to grab a couple things in the garage, jumped back in and it quit before I could get it in gear and roll out. Weird. This is the first time I've ever had to get a tow.
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: Got Error Message P1670 / P0381 - Low Oil Pressure - Won't Start?
I had new glow plugs installed 3 weeks ago. Ran fine since. Today, first cold day. No start, oil pressure gauge does not move off zero, interceptor reads ICP 126. Oil level is good. WTS light does come on. Checked fuse 19 as I saw on another thread, it is good.
P1670 and 0381. My ford software is down, trying to reinstall. As soon as it is reinstalled, I can go thru the step process?
Ford 6.0L Power Stroke Diesel :: Truck Does Not Even Crank And It Has No Fuel Pressure
I was driving to a job this morning with my truck loaded with tile for a job and it just died.
It has power to the lights, radio, etc. But when I try to start it it does not even crank and it has no fuel pressure on the gauge and the pump is no running.
It is as if the truck has no power. When it died is was like I turned the key off and it just stopped.
Ford 6.7L Power Stroke Diesel :: 2011 F250 Won't Start After Getting Reduced Engine Power Message
I have a 2011 Ford F250 6.7 Powerstroke. It has 107,000 miles on it.
The other day I was driving it down the highway and it got a Reduced Engine Power message on the dash. It lost power and I got off the highway to the service road. Then it died on me.
Had to get it pushed to a station then towed home. It wouldn't start. The starter cranks over for a few seconds but engine won't start. Checked all the fluid levels and batteries. My DEF fluid was only a half gallon low.
What I have noticed is that the DEF level indicator hasn't reminded me that it was low for over 4-5 months now. I had been putting in about 2-3 gallons every 3 months or so. But it hasn't reminded me lately and I just forgot. This is my first diesel.
Ford 6.0L Power Stroke Diesel :: Losing Coolant Pressure - Pin Hole Leak Somewhere Once Shut The Truck Off
I noticed when I shut off the truck about 30-40 minutes later I'll open the degas bottle cap and notice there is no pressure.
I used a coolant pressure tester kit and pumped in 16PSI but couldn't hear or find the leak.
I'm going to buy a smoke machine in a month or two but until then, can I still drive the truck ?
I'm guessing it is a pin hole leak somewhere as once I shut the truck off... there is a lot of coolant pressure.
Ford 6.0L Power Stroke Diesel :: 2006 - Won't Start When Hot - Oil Pressure?
Background: My 06 started up and ran fine until #7 injector took a crap.I had the injectors replaced with 155/stocks from warren.
Well no we're having an issue with a hot no start. Starts and runs just fine cold but once up to temp and you shut her down you can't start it again till it cools. Air tested it 3 different times can't find any leaks. Swapped out the ipr with a new one my mechanic had just to see and no change, unplugged it and no change.
What it could be. When warm and trying to start it only gets 300psi. The only other thing i can think of is hpop, but to go just like that without any trouble before hand has me puzzled.
Ford 6.0L Power Stroke Diesel :: 2004 - No Oil Pressure At Start Up
I have a 2004 late model 6.0. My son was driving it and parked it in the road told him move it and it wouldn't start. I got it to start and it ran for about 10 seconds. I pushed it in the drive way and left it over night. In the morning there was oil on the driveway. I found that there was the wrong oil filter put in and there is no oil pressure at start up and no oil entering the filter housing. Where to start would be great. I am going to get a Scangauge II to get more information. Could be the ICP?
View 4 RepliesFord 6.0L Power Stroke Diesel :: 2003 F250 - Not Enough Pressure To Start
I have a 2003 F-250. For 8 months now we have been trying to get my truck to start. We have replaced the High pressure oil pump, Oil cooler, PCM, Main wiring harness, FICM, Injectors,, ICP, and IPR. Still we are not getting enough pressure to start the truck. What is happening is the pressure will get to about 340 and will not increase from there. If we are to disconnect of one the connectors from the FICM the pressure will reach 640. Now we are able to get the truck started with ether, but will not remain started. As of right now we are still trying to figure out what is causing this problem?
View 14 RepliesFord 6.0L Power Stroke Diesel :: Front Of Truck Covered In Coolant - No Coolant Pressure - Fix?
Well got home and the front of the truck was covered in coolant. I must have driven 2 hrs after I noticed no coolant pressure, but temperature was great so figured it was another crappy cap. Looking to get a quick turnaround. Need to go out of town for work Saturday so I have this week to get it done.
Just put a stock unit back in? I don't think I need to do anything else in that area. Belt/pulleys/radiator all done last spring.
Ford 6.0L Power Stroke Diesel :: Truck Hard To Start / No Power At All
I removed all 8 injectors because my truck felt like it had a dead cylinder one morning after I did oil change and filter and fuel filters. Truck ran great the day of the fluid change. The next morning however truck was hard to start no power at all nothing. Felt like a dead cylinder so removed all 8 injectors and ohm them all ohm at 0.4 to 0.5 except number 4 injector it ohm at 0.4 and 0.7 that's not in spec right or am I wrong? Do I need a new solenoid? Keep in mind tho number 5 and 8 injectors had contribution codes but they ohm good. So I'm going to tear the injectors apart and see what's what. But my question is do I need to replace number 4 injector solenoid?
View 3 Replies