Ford 6.0L Power Stroke Diesel :: Truck Started Cranking Longer Than Normal To Start After Sitting For More Than 2 Hours
About 7 months ago my truck started cranking longer than normal to start after sitting for more than 2 hours. This went on for about 3 weeks, then it started normally again. (By longer crank time, i timed it between 5-7 seconds on average. Normal is about 2 seconds). Now it has started doing this again about 4 weeks ago. Now I'm thinking HPO slow leak. Yesterday all is good again. What should I be looking for as a starting point to fix this permanently? When it cranks longer, the icp stays at 0, the ipr goes to 77%. Then it just fires off. No slow build of pressure. You can see all my mods and updated parts in my sig. I wonder if one of the new dummy plug o-rings is starting to give up already after only 15k miles. (Batt voltage is at 13.9-14.2, ficm is at 49.5 steady).
View 5 RepliesFord 6.7L Power Stroke Diesel :: Oil Temp 224 And Tranny 199 At 9k Miles Only - Normal?
I have a 12 cc 4x4 drw. I hauled a bull and a cow about 100 miles this morning. I was pullling approx 6k including the trailer. The temp was about 75*. 50-60 miles into the trip I switched to the oil temp screen and the oil temp was 224* and the trannie was 199*. I was going into the wind which was about 20 mph, and I was traveling 75mph. The truck never lugged down heck it never shifted out of 6th gear. When I unloaded the cattle the temp came back down around 190*. Headed home and the temp got up to 226* and the tranni went to 205*. This was going with the wind and just the trailer. I am using oem 10w-30 motorcraft and motorcraft filters. The truck just has 9k miles on it. I am thinking that the oil temp is a little warm, should I be worried. What should I look for to diagnose. I like to do my own diagnosing if I can, the dealers around me can't find anything wrong even if you point the leak out to them. Should I be using a different oil?
View 14 RepliesFord 6.7L Power Stroke Diesel :: How Long Tranny Temp Takes To Get Up To Normal Range
I know that average normal tranny temps for the new 6.7s are 200 degrees give or take which my truck does as well. but I'm wondering about how long is normal for the tranny temp to get up to that normal range? My truck can take anywhere from 20 minutes to almost an hour depending on if I'm on highway vs lower speed driving and it's been that way since I bought it. Am I worrying over nothing or my worries not just worries?
View 7 RepliesFord 6.0L Power Stroke Diesel :: AC Blow Cold For 10 Minutes Until Everything Is Up To Normal Operating Temp
When I fire her up, the AC will blow cold for 10ish minutes until everything is up to normal operating temperature. Then it tends to blow warm, and that last for about 20 minutes, before finally settling back down and being cold AC again. I initially thought it was an issue with my compressor disengaging, but it doesn't seem to be...
View 3 RepliesFord 6.0L Power Stroke Diesel :: Cooling System / Temp Gauge Started To Rise Past Normal Before Fan Comes On
I have a 2007 6.0 that this has happened to twice now. It's fine around town but I never hear the can come on. Friday when on the interstate my my temp gauge started to rise past normal operating temperature before fan came on. Is this normal? After the fan came on it stayed at normal temp for the rest of trip....
View 5 RepliesFord 6.0L Power Stroke Diesel :: Missing Only When Engine Up To Temp
To start off. I have a 2004 F350 with the 6.0 in it which just had a top end rebuild done on it due to the head gasket blowing on it. During the rebuild the EGR cooler was also deleted, ARP head studs, Heads were milled down to make them flat (shop said they had to take 9 thousands off to do so), new up pipes installed, new back pressure sensor installed due to the plug head snapping off, new glow plugs, new glow plug rail harness, oil rail rebuilt due to bad o-rings on the ball tubes, injectors were installed with all new seals and had polished the spool valves hoping to avoid stiction (however its spelled can never remember), and lastly the EGR was deleted electronically with tuner. Also had to get 2 new batteries as they were stone dead and would not take a charge. And had to get a new alternator due to low output. Not sure if the alternator killed the batteries or the batteries killed the alternator either way it needed replaced to.. Unfortunately after i got that fixed i had to get a new starter as it died 3 days later.
Ever since its gone back together Ive had a consistent intermittent miss with the truck. Ive searched every article i can find but seems most complain about misses when cold. Mine is the exact opposite as it only does it once the engines up to normal operating temp. It accelerates hard and fast like it has no issues. While its cold it doesnt miss at all. Once its warmed up sometimes while cruising it will feel like its missing on every cylinder or better description would be as if your driving on a cobble stone road.. If you mash the pedal for a couple seconds till it kicks down and raises the rpms it stops.. Its most prevalent at idle though.. You can literally hear the difference in the engine when it starts missing. Truck will shake as if its got a large lopey cam. Odd part while sitting at idle it will cycle back and forth between running smooth and missing. But same with at cruise as soon as you get on the throttle it goes away. If its doing it while sitting idle at a light, it will take a couple seconds once your on the throttle for it to smooths out. But always does.
Ive tested the Ficm hot and cold, KOEoff and KOEOn.. getting a steady 48v from the main board.. Scan gauge says the Logic boards reading steady 13v... Also from the scan gauge it says my ICP pressure is in the 640 range at idle (full throttle highest ive seen is 3600psi so dont think its a pressure leak) and volts bounce between .80-.90.. but oddly once it starts missing the ICP pressure jumps up 20 psi.. IPR at idle reads 23.5-25.5.. at cruise its up around 45ish.. fuel pressures said to 70 psi.. which its usually around that most times, cruising itll be around 66psi. I had 3 injectors replaced not this past spring but the year before (ironically same symptoms).. Injectors 5,7,8 were replaced then.. ICP sensor was also replaced at the same time as it split and shorted out the connector which was the initial reason i took it in that time since it was dumping the oil on the ground.
I dont have any way to perform a cylinder contribution test and after spending 6K on a rebuild I really cant afford to take it in to have someone else do it. A local guy was able to scan the truck for me but he couldn't do the contribution test either but was able to buzz test them. Everything passed there but we also found some hidden fault codes my code readers did not find. The ones we found hidden said that injectors 2, 4, and 7(again??) are reading low contribution. Of what I've read 2 & 4 sit on either side of 7 in the firing order so have wondered if they're not pulling down 7's results.
I really cant afford to replace the injectors till near the end of next month. Is there anything else I can look at that might actually possibly be causing false readings or intermittent misses only when warm.
Ford 6.0L Power Stroke Diesel :: How To Determine Engine Temp
I'm about to take my ambulance on its first road trip but I'm skeered because the OBDII connector is dead so my ScanGauge doesn't work. The temp gauge always says normal, but several times I have heard the fan kick on for a few seconds when driving in routine conditions. Is that normal with these big vans? Is the weight of the ambulance box so much that the fan has to kick in more often?
Again, when I've heard the fan, it only came on a few seconds. My only experience is with the Fseries 6.0s I've had - when those fans came on, the temp would be at least 205, usually more than 210, and it would run longer. However, those were always pulling a trailer, which I guess is about the same as the heavy ambulance box.
Is there any way to tell whether the engine is running hot besides the truck's idiot gauge?
Ford 6.0L Power Stroke Diesel :: White Smoke When Engine Is Getting Up To Temp - Over Fueling
Massive amounts of white smoke (fuel) when engine is getting up to operating temp. It clears up for the most part when its fully warmed up. It sounds like its hitting on all 8. Runs great for the most part. Do I need to go to a dealer to pull codes. Ive gone to auto zone for there code read and addressed a egr valve issue. It is cleaned and unplugged for now.
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2004 - Engine Coolant Temp Gauge Does Not Work
Bought this truck, and the engine coolant temp gauge does not work, so I replaced the sender, still don't work.
View 8 RepliesFord 6.0L Power Stroke Diesel :: Oil Temp Lower Than Coolant Temp
Ever since having the EGR delete done, the oil temp has been LOWER than the coolant temp. I am assuming this is bad info from the sending unit? They are reading with in a degree of each other at start up, but when at operating temp the gauge will read lower. Before the EGR delete I had a delta of about 4-7* oil hotter than coolant.
View 1 RepliesFord 6.0L Power Stroke Diesel :: 2004 F350 - Poor Acceleration When Engine Is At Operating Temp
I have a 04 f350 6.0 with about 195xxx miles on it. The other day my truck started acting up. It starts and idles without a problem and drives fine till the engine gets to operating temp once there I cannot accelerate quickly like getting onto the highway to get up to speed it just the motor just goes quiet and won't accelerate. It usually does this a little after 2000 rpm. I can let off the throttle and slowly get to speed as long as I don't go past 2000 rpm. No check engine light was not on scanned it and got p0611 for the ficm. I tested the ficm and it read 48v with key on. While truck was running I got 46.xx v then Started to climb to almost 48v. The truck was warm but not at operating temp where the problems starts(didn't have time to let it warm up all the way) could these symptoms be the ficm still? What else should I test?
View 5 RepliesFord 6.7L Power Stroke Diesel :: Check Engine Light Came On / Code P0181 Fuel Temp Sensor
Just over 6000 miles....Yesterday morning the light came on. Dealer wouldn't look at it for a week. Went to my mechanic this morning to check the code it was p0181 fuel temp sensor. I read something online about the block heater making it too warm. The other night it was cold so I plugged it in, then yesterday morning it got warm overnight like into the lower 40s. I noticed the grill felt warm too. My mechanic cleared it if it comes back on do I have an issue? Is it ok to drive?
View 14 RepliesFord 6.0L Power Stroke Diesel :: No Start If Sitting For Between 10 To 90 Minutes
I have an 06 f250 w/ 6.0. Having a no start problem. If my truck is warmed up and sits for 5 min or so and try to start it, it starts fine. If it sits longer than that , no start. But if I wait about an hour and a half, it starts right up. Why would it not start if sitting for between 10- 90 min. Starts fine cold.
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2006 - Won't Start After Sitting For 2 Weeks?
06 6.0 f250, I went out of town for 2 weeks came back home and went to jump in my truck and it seemed like it almost started but didn't then slowly each time I tried it seemed like the battery was draining down. Is this just from it sitting for so long without cranking or is it something else my scangauge says I'm getting 11.5 volts. Do I need to just jump it off or get a whole new battery. Or is it another issue?
View 2 RepliesFord 6.0L Power Stroke Diesel :: Puddle Of Coolant Under Truck After Sitting?
Having a puddle of coolant under truck after sitting. Shop said its a oring on the egr cooler. 1200.00? Is that normal?
View 14 RepliesFord 6.7L Power Stroke Diesel :: Truck Idle / Spool Up And Down When Just Sitting?
My truck when idling kind of spools up a little bit for a few seconds and then the turbo goes back down. sounds really cool actually. its been doing it since the truck was new, sounds like a plane engine shutting down. It does it over and over sometimes. I just deleted the dpf and unplugged egr last night and now i can really hear it! is this normal....
View 10 RepliesFord 6.0L Power Stroke Diesel :: Turbo Up To 30 Psi Normal?
My truck is all stock and I am running in performance tune? And my friend the former owner said I need to let her loose about 75 percent of the time I am driving it because it's my DD and I do not tow anything on a regular basis. I do not want to stretch my bolts by unnecessary pushing, I don't know if I'm even pushing it hard but I normally get the turbo up to about 30 psi is that to much?
View 8 RepliesFord 6.0L Power Stroke Diesel :: Long Cranking Time When Sitting For Over 5 Hours
2005 Ex with 6.0. It has been bulletproofed. But has had a long crank after sitting for over 5 hours. I was starting to think glowplugs but no codes, Then thinking FICM, nope voltage has always been good. After I run the truck for a few miles if I kill it. It would crank right up. No issues. Only happened after it sat for awhile. I knew it had to do with HPOP system since it took about 5 to 8 seconds to show over 500PSI.
The passenger side does not have a leak since the oil is to the top of ICP sensor. When I was going to remove it. So I took off the drivers side. I inspected the dummy plug. No issues there "they are the 12mm with teflon plugs" I inspected the stand pipe. No issues there either. I inspected the small test port on the top of the rail. No issues there either. So I decided to air test it. So I used my auto-ingenuity to close the IPR valve after I heard all the oil blow out.
Then after sitting with 120 psi of air for about 10 minutes. I hear a bubbling sound coming from the Drivers side Rail. It was a plug I have never seen mentioned here. It is at the back of the rail. I removed it and sure enough the oring is split in 2. I went to ford and picked up a new Oring it was like $4. It also looks like its a different material. I am still in the process of putting the truck back together so i have not started it back up. But I am pretty sure this was my problem.
Ford 6.0L Power Stroke Diesel :: 2004 - Normal ICP Readings?
I have an early 04, I'm not sure if there's a different in pressure over the years. But I'm curious what normal or average readings are. Btw I did replace the icp and pig tail last year. Here is what I have in psi from my sct
Cold start at idle 680 .23v
Warm idle 635 .24v
Cruising 1800rpms about 1500 .32v
WOT about 4200 .78v