Ford 6.7L Power Stroke Diesel :: 2013 - Low Pressure Fuel Pump Housing Cracked?
This pump hangs down fairly low and appears easy for ice and rocks to hit on my 2013. Something hit mine and took a chunk out of the drain tube. No leaks yet but I am looking to get a new one and keep this as a spare, or just JB weld it. Can I just buy the lower section, or do I need to get entire pump?
Any creative protection bracket made? Would just have to take it off to change filter though. Any leak in this housing is a major show stopper when in the middle of nowhere! Maybe why it is getting brought into the tank on new models?
Ford 6.0L Power Stroke Diesel :: Possible Plugged Oil Cooler Or EGR Cooler?
I have a 04 that has 153k on it. 4" cat back exhaust with no cat. SCT tuner running a custom street tune. New FMIC with the extra tune on it. Head gaskets where done at 90k along with ARP studs. EGR cooler, The oil cooler was cleaned, New coolant tank. 1-new head and The cooling system was flushed at 90K. All done by the dealer along with some other items. Installed a bypass coolant filter at least 60k miles ago.
I have been having a no heat issue sometimes at idle this past winter and a mystery loss of coolant. I replaced the cap with a OEM one. I did a vacuum test on the coolant it held at 25 inches for well over a 1/2 hour. Pulled the egr valve it looked somewhat like tar inside not 100% dry. At startup it sometimes blows some white smoke and other times it's black smoke. I've had the scan gauge on for the last week to check my deltas.
Running 65mph the deltas stayed around 10 degrees diff.
Running 70mph the deltas stayed around 14-16 degrees diff.
Yesterday just running around rural roads 55mph and under the deltas stayed around 10 degrees diff.
I have not found a lower pressure gauge to do a coolant pressure test.
It does look as though it has burped the cap. Because of the deltas I'm thinking a plugged oil cooler my be the problem.
Ford 6.0L Power Stroke Diesel :: Bulletproof Diesel Oil Cooler
What is the consensus on this setup? Is it worth the money? Or is it more hype than function? Their logic behind it definitely seems to make sense.
View 11 RepliesFord 6.0L Power Stroke Diesel :: EGR Cooler Is Bad
Just found out that my EGR cooler is bad. How big of a job is this/how much down time if a compatent tech is doin the job?
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2006 - How To Get Out Thermostat From Housing
'06 powerstroke, 215k stock
Doing a coolant flush, took the thermostat out but cannot figure out how to get it out of the housing.
Ford 6.7L Power Stroke Diesel :: DFCM Housing Broke?
I was twisting off the DFCM housing when I heard a pop and alot of fuel leaking. It appears I sheared off the 32mm plastic nut. I know for a fact that I was turning it counter clockwise just like the manual stated. Now what do I do? I cant run my SD can I? The simplest solution is to get another housing and install it but im not sure ill be able to get the remnants of the original housing off with out the nut to twist it. I watched Epics video on changing the filter and his came off with little effort? My same story just different result.
View 14 RepliesFord 6.0L Power Stroke Diesel :: Bell Housing Drips Twice?
So I have a bit of an oil leak, bell housing drips once or twice while it is parked for a day or so and usually has a drip hanging off of it. Where the starter mounts also has some oil and there is some of the driver side. The valley is totally dry and I have new CAC boots so it isn't coming from up there. When I look through the inspection port it doesn't look like it is from the rear main. I figure this leaves either bedplate or cam/crank sensor. Any thoughts on how to narrow it down further? Maybe put dye in the oil? It looks somewhat oily up by the cam sensor but it is so hard to see that thing I can't tell very well.
View 10 RepliesFord 6.0L Power Stroke Diesel :: Oil Cooler Clogged
I just replaced my oil cooler and 500miles later its clogged again. Delta reached 40F.. No fun... I replaced it with the factory ford cooler and installed the coolant filter but I guess when I did the first flush I missed sum gunk.
So my question to you PROs, should I reflush/restore again then replace the cooler? OR Go with one of these??
- Coolant-to-Liquid Oil Coolers
- IPR External Oil Cooler Kit for Ford 6.0 Powerstroke
The budget is tight, but I gotta keep the truck going.
Ford 6.0L Power Stroke Diesel :: BPD Cooler - No Filter
I'm considering the BPD cooler MINUS the filter. Anything wrong staying with the original filter?
View 7 RepliesFord 6.0L Power Stroke Diesel :: Replace Oil Cooler?
Well it looks like I'm going to have to put a new oil cooler on my truck. Does ford have an upgraded version or do they still offer the same cooler?
View 5 RepliesFord 6.7L Power Stroke Diesel :: Cracked Fuel Filter Twice?
Within the last month I've had 2 cracked fuel filters the filter up by the engine...
View 12 RepliesFord 6.7L Power Stroke Diesel :: Cab Light Bases Cracked
Swapped out the orange covers for smoke ones on my truck and noticed that 4 out of 5 bases have cracks at the rear end of the lights. One screw would barely hold in as the plastic around the screw was all cracked which makes the hole larger. Is this a common issue?
View 9 RepliesFord 6.7L Power Stroke Diesel :: Power Loss - Code P0401 - EGR Cooler Is Clogged
My 2011 has 62k miles and has been throwing P0401 codes, which results in losing power. I assume the EGR cooler is clogged. So I went to the dealership to see if it's covered, and was told there's no warranty coverage.
I would rather blockoff the EGR cooler than repair it. I would also like the extra performance from a tuner like the MiniMaxx. I do prefer the stock exhaust and not real excited about the drone/smell that comes with deleted DPF.
Will I have issues if it's tuned with the EGR blocked off, and stock exhaust? Or am I better off doing a full delete at this point?
Ford 6.7L Power Stroke Diesel :: Coolant Running Down All Over The Bell Housing And Oil Pan
The same day that I noticed my coolant temp was running high as I was driving around in my 2011, i was driving around in my corn field cutting wood and i noticed i was dragging something under the truck. when i got out and looked under the truck, there was coolant running down all over the bell housing and oil pan. i was a bit worried that it was my head gaskets leaking but once i got it in the shop and looked at the heads, all looked good. i wasnt sure where it was coming from! so i looked up common coolant leaks on the 6.7 on youtube.
First video was one of the coolant line on the turbo leaking. so i crawled up on top and shoved a mirror down by the turbo and sure enough i could see coolant leaking around the connector fitting coming out of the turbo. apparently the gasket goes bad around this fitting allowing it to leak. i was just wondering if this is really that common of an issue? I did the work myself. and its not really that hard to get to the turbo, its just time consuming removing all the crap around it. all i had to do was remove some connectors that were attached to the plastic intake and remove the intake then you can reach into that fitting. total time was around 2.5 hours.
Ford 6.0L Power Stroke Diesel :: Oil Leak Under Turbo Compressor Housing
I have a small oil leak that is showing up under my turbo compressor housing. It's starting to show a little in the valley. Not a big leak, just not sure were the source is and would like you opinions and recommendations. I have been cleaning it up every few days, drive it then use a mirror and rag to try and locate the source.
Here are some pics, I hope I took some that are good enough. Unfortunately I cleaned up the oil before the pics, but I circled and marked the location.
Concerned about the turbo, but I don't understand this leak since it's not coming from the center section. The turbo drain pipe is new and it does not seem to be coming from there. The leak is not enough to show a change on the dipstick the last 3-4,000 miles as far as I can tell.
Ford 6.0L Power Stroke Diesel :: Filling Up Oil Cooler After Replacement
Is there a way to fill up the reservoir for hpop and cooler after replacement? I didn't want to burn down the starter and kill batteries cranking all day until everything is full. I did the usual upgrades on the motor and about ready to try and get it started up. Where does the oil drain to when filter is removed?
View 3 RepliesFord 6.0L Power Stroke Diesel :: High Oil Temp After New Oil Cooler
My dad's 03 has had some work done after his oil cooler was clogging. New oil cooler, egr delete, head studs etc. The oil temp seemed to run some what high when he got it back. After a couple interstate runs on cold days 15-20 degrees, the water ran around 185 and oil as high as 218 but usually a bit lower. What's going on here? how could this thing be clogged again? It hasn't seem to gotten much worse since we got it back but not better either.
View 8 RepliesFord 6.0L Power Stroke Diesel :: No Boost After Oil Cooler Replacement
Got everything done today. So I thought. Went for a drive. turbo not building boost. I checked the map hose and barb. Clean. Checked connection at ebp and vct, both plugged in. No exhaust leaks. turbo shafts feels good and spins good. made boost fine before repairs. 2006 6.0 f250 .....
View 14 RepliesFord 6.0L Power Stroke Diesel :: Oil Cooler Backflush Before Replacement
2004 6.0 90k miles... Oil cooler plugged & coolant puking due to egr cooler flash boil.
Flushed the coolant with tap water then replaced water pump and tstat weekend before. This week backflushed heater core & block. This weekend backflushed the oil cooler. My coolant system would be considered severe contamination due to tap water use resulting in rust. Average ect was 195-205 & avg eot was 230-240 before flush. Here's a baseline before flush.
Pulled the oil cooler exhaust cap, opened both block drains, pulled lower radiator hose, & hooked up otc blast vac. The pressure was pretty intense holding the hose into the bore just running water through it. Hit the trigger about 20 cycles of water then air blasts.
Filled with 1/2 gal of restore & tap water. Ran it for 2 hours with RPM 1k+ 95% of the time. Drove at 65 mph & grabbed some peak temps.
Then dumped restore while hot, was pretty cloudy but not that dirty. Let engine cool then filled with tap water, ran for 10 mins then dumped again. Stuck hose in degas with only the the drivers block plug pulled & revved engine a few times to have the water pump push any crap out. Pulled the oil cooler exhaust cap, opened both block drains, pulled lower radiator hose, & hooked up otc blast vac again. This time the back pressure on oil cooler was much less vs first time.
Took a mason jar with restore plus in it & boiled it in water. Got it up to 190 then poured it directly into the oil cooler & let it sit for 30 minutes. Then backflushed again.
Put rest of the whole gallon of restore plus in & topped off with tap water. Ran again for 2 hours with RPM 1k+ 95% of the time. Drove at 65 mph & grabbed some peak temps.
Dumped restore plus while hot & it was very green & contaminated with rust. Topped off with tap water, ran for 10 mins at 190 then dumped. Revved the engine again with hose in the degas bottle & only drivers block plug out to blow more junk out. Filled with tap water & dumped again.
It was late last night so I filled it with distilled & parked it. Plan to do 3 straight distilled water flushes this week running rpm 1k+ for 1 hour each time in hopes to rid all the chemicals.
The backflush didn't result in lower deltas, but it didn't puke from the degas bottle at all during both chemical flushes. The oil cooler definitely needs replaced but at least it's not puking anymore & will hopefully stay this way for about 1k miles of driving so I can let the coolant filter rid anything that breaks loose during driving. My hope was to get some sort of flow across the egr cooler to stop the flash boiling puking & get as much junk out of the system as possible. So I guess there's some sort of achievement in the end.
Currently running cheap regular green (mixes with all) elc. I am running the cheap stuff because when the coolant was puking a gallon of coolant every trip i couldn't justify upgrading to the Rotella ELC yet. Plan is to flush with rest of restore(1/2 gallon) after oil cooler r&r then switch to Rotella ELC.