Ford 6.0L Power Stroke Diesel :: IRP High Flow Oil Cooler
Is the irp high flow oil cooler any good? Or is it better to stay with the oem
View 14 RepliesFord 6.0L Power Stroke Diesel :: Possible Plugged Oil Cooler Or EGR Cooler?
I have a 04 that has 153k on it. 4" cat back exhaust with no cat. SCT tuner running a custom street tune. New FMIC with the extra tune on it. Head gaskets where done at 90k along with ARP studs. EGR cooler, The oil cooler was cleaned, New coolant tank. 1-new head and The cooling system was flushed at 90K. All done by the dealer along with some other items. Installed a bypass coolant filter at least 60k miles ago.
I have been having a no heat issue sometimes at idle this past winter and a mystery loss of coolant. I replaced the cap with a OEM one. I did a vacuum test on the coolant it held at 25 inches for well over a 1/2 hour. Pulled the egr valve it looked somewhat like tar inside not 100% dry. At startup it sometimes blows some white smoke and other times it's black smoke. I've had the scan gauge on for the last week to check my deltas.
Running 65mph the deltas stayed around 10 degrees diff.
Running 70mph the deltas stayed around 14-16 degrees diff.
Yesterday just running around rural roads 55mph and under the deltas stayed around 10 degrees diff.
I have not found a lower pressure gauge to do a coolant pressure test.
It does look as though it has burped the cap. Because of the deltas I'm thinking a plugged oil cooler my be the problem.
Ford 6.0L Power Stroke Diesel :: Oil Temp Too High?
I know they're supposed to be within 15 deg of each other. How bad is this? Pulling a small trailer with a polaris rzr on it. Running 75mph
View 14 RepliesFord 6.0L Power Stroke Diesel :: Oil Temp Running High
I recently noticed on my truck that my oil temp was running high, I would go down the interstate at 75 mph and the oil temp would get up to 215-218 while my coolant temp would sit around 192-196. So, I took it into the shop and was told it was most likely a bad oil cooler and had it replaced 2 years ago when I had my injectors and gaskets replaced along with my egr deleted. So, got the truck yesterday, going 60mph down the highway, truck ran an oil temp of 192 and the coolant at 188. Was great, but later on once I got to the interstate going my 75 mph, The oil temp jumped to 209 and my coolant sat at 192. Not sure what the deal is, was told the oil cooler was replaced and wanted some input on what else I could be looking at. I currently have 5w40 synthetic oil running in it. I have an EDGE CTS tuner on it and tuned it back to stock mode, but oil temp still jumps up to 209 and coolant remains around 190-192.
View 14 RepliesFord 6.0L Power Stroke Diesel :: High Trans Temp After 08 Pan And Filter Upgrade
Trans temp used to be about 185 max, now it's running side by side with coolant temps (200-203 with Mishy 200 thermostat) after I did the 08 pan and filter upgrades. I added 9.5qts after the change of Valv Max Life and checked and double checked the dip stick bout half way up hot. This is normal operating conditions, not towing anything. Checked with TorquePro App. Why it would run so high? Did I do something wrong?
View 14 RepliesFord 6.0L Power Stroke Diesel :: High Pitched Squeal - Coolant Temp At About 180 Degrees
I have a 2006 350. When I am pulling my camp trailer (about 12,500 lbs) up a grade I hear a fan or blower turn on and I get a high pitched squeal. It will also have a beep and my in dash display will say high engine temp. I have a bullydog pmt programmer (i tow with it in stock mode) the display will show my coolant temp at about 180 degrees. If I pull over and let it idle for about 2 minutes the warning clears and the temp gauge returns to normal. the display reads about 180 degrees the whole time this goes on. I know the engine is not over heating so why do i get this warning and squeal?
View 4 RepliesFord 6.0L Power Stroke Diesel :: Intake Air Temp Sensor One Circuit High And Strange Idle?
I have a code for iat sensor 1 circuit high. It's the only code I can pull. I replaced the sensor in the manifold and still no change. The truck revs up when started but kinda finds its idle rpm after a second and the idle fluctuates some when the truck is warmed up too. I have a snap on solus and all parameters seem to be good. Icp sensor is also new thinking it might be the cause. Other than that the truck runs perfect and doesn't miss a beat.
View 14 RepliesFord 6.7L Power Stroke Diesel :: 2015 - Code P0073 For Ambient Air Temp Sensor Circuit High
I'm excited to be a Powerstroke owner again! I had a 2000 with the 7.3L and since bought and now sold a Chevy 1500. Last week I bought a new 2015 6.7L. I am MORE than impressed and love the truck. Today I brought it to get the windows tinted. I have not had one issue with the truck since I have had it. When they finished with the windows, my check engine light was on. The shop I had it done it EXTREMELY reputable. They brought out their snap on scanner and pulled the code. p0073 for the ambient air temp sensor circuit high. Is this a coincidence that this came on after they got done, or could something they did while tinting the windows tripped this?
As I drove off down the road after determining I wasn't going to hurt the truck, the air temp sensor went from showing -40 to the actual temperature. What would cause this? I deleted the code when I got home with my actron, and the MIL has stayed off since, however, it shows P0073 Permanent ...
Ford 6.0L Power Stroke Diesel :: Bulletproof Diesel Oil Cooler
What is the consensus on this setup? Is it worth the money? Or is it more hype than function? Their logic behind it definitely seems to make sense.
View 11 RepliesFord 6.0L Power Stroke Diesel :: EGR Cooler Is Bad
Just found out that my EGR cooler is bad. How big of a job is this/how much down time if a compatent tech is doin the job?
View 14 RepliesFord 6.0L Power Stroke Diesel :: Oil Temp Lower Than Coolant Temp
Ever since having the EGR delete done, the oil temp has been LOWER than the coolant temp. I am assuming this is bad info from the sending unit? They are reading with in a degree of each other at start up, but when at operating temp the gauge will read lower. Before the EGR delete I had a delta of about 4-7* oil hotter than coolant.
View 1 RepliesFord 6.0L Power Stroke Diesel :: Oil Cooler Clogged
I just replaced my oil cooler and 500miles later its clogged again. Delta reached 40F.. No fun... I replaced it with the factory ford cooler and installed the coolant filter but I guess when I did the first flush I missed sum gunk.
So my question to you PROs, should I reflush/restore again then replace the cooler? OR Go with one of these??
- Coolant-to-Liquid Oil Coolers
- IPR External Oil Cooler Kit for Ford 6.0 Powerstroke
The budget is tight, but I gotta keep the truck going.
Ford 6.0L Power Stroke Diesel :: BPD Cooler - No Filter
I'm considering the BPD cooler MINUS the filter. Anything wrong staying with the original filter?
View 7 RepliesFord 6.0L Power Stroke Diesel :: Replace Oil Cooler?
Well it looks like I'm going to have to put a new oil cooler on my truck. Does ford have an upgraded version or do they still offer the same cooler?
View 5 RepliesFord 6.7L Power Stroke Diesel :: Power Loss - Code P0401 - EGR Cooler Is Clogged
My 2011 has 62k miles and has been throwing P0401 codes, which results in losing power. I assume the EGR cooler is clogged. So I went to the dealership to see if it's covered, and was told there's no warranty coverage.
I would rather blockoff the EGR cooler than repair it. I would also like the extra performance from a tuner like the MiniMaxx. I do prefer the stock exhaust and not real excited about the drone/smell that comes with deleted DPF.
Will I have issues if it's tuned with the EGR blocked off, and stock exhaust? Or am I better off doing a full delete at this point?
Ford 6.0L Power Stroke Diesel :: Filling Up Oil Cooler After Replacement
Is there a way to fill up the reservoir for hpop and cooler after replacement? I didn't want to burn down the starter and kill batteries cranking all day until everything is full. I did the usual upgrades on the motor and about ready to try and get it started up. Where does the oil drain to when filter is removed?
View 3 RepliesFord 6.0L Power Stroke Diesel :: No Boost After Oil Cooler Replacement
Got everything done today. So I thought. Went for a drive. turbo not building boost. I checked the map hose and barb. Clean. Checked connection at ebp and vct, both plugged in. No exhaust leaks. turbo shafts feels good and spins good. made boost fine before repairs. 2006 6.0 f250 .....
View 14 RepliesFord 6.0L Power Stroke Diesel :: Oil Cooler Backflush Before Replacement
2004 6.0 90k miles... Oil cooler plugged & coolant puking due to egr cooler flash boil.
Flushed the coolant with tap water then replaced water pump and tstat weekend before. This week backflushed heater core & block. This weekend backflushed the oil cooler. My coolant system would be considered severe contamination due to tap water use resulting in rust. Average ect was 195-205 & avg eot was 230-240 before flush. Here's a baseline before flush.
Pulled the oil cooler exhaust cap, opened both block drains, pulled lower radiator hose, & hooked up otc blast vac. The pressure was pretty intense holding the hose into the bore just running water through it. Hit the trigger about 20 cycles of water then air blasts.
Filled with 1/2 gal of restore & tap water. Ran it for 2 hours with RPM 1k+ 95% of the time. Drove at 65 mph & grabbed some peak temps.
Then dumped restore while hot, was pretty cloudy but not that dirty. Let engine cool then filled with tap water, ran for 10 mins then dumped again. Stuck hose in degas with only the the drivers block plug pulled & revved engine a few times to have the water pump push any crap out. Pulled the oil cooler exhaust cap, opened both block drains, pulled lower radiator hose, & hooked up otc blast vac again. This time the back pressure on oil cooler was much less vs first time.
Took a mason jar with restore plus in it & boiled it in water. Got it up to 190 then poured it directly into the oil cooler & let it sit for 30 minutes. Then backflushed again.
Put rest of the whole gallon of restore plus in & topped off with tap water. Ran again for 2 hours with RPM 1k+ 95% of the time. Drove at 65 mph & grabbed some peak temps.
Dumped restore plus while hot & it was very green & contaminated with rust. Topped off with tap water, ran for 10 mins at 190 then dumped. Revved the engine again with hose in the degas bottle & only drivers block plug out to blow more junk out. Filled with tap water & dumped again.
It was late last night so I filled it with distilled & parked it. Plan to do 3 straight distilled water flushes this week running rpm 1k+ for 1 hour each time in hopes to rid all the chemicals.
The backflush didn't result in lower deltas, but it didn't puke from the degas bottle at all during both chemical flushes. The oil cooler definitely needs replaced but at least it's not puking anymore & will hopefully stay this way for about 1k miles of driving so I can let the coolant filter rid anything that breaks loose during driving. My hope was to get some sort of flow across the egr cooler to stop the flash boiling puking & get as much junk out of the system as possible. So I guess there's some sort of achievement in the end.
Currently running cheap regular green (mixes with all) elc. I am running the cheap stuff because when the coolant was puking a gallon of coolant every trip i couldn't justify upgrading to the Rotella ELC yet. Plan is to flush with rest of restore(1/2 gallon) after oil cooler r&r then switch to Rotella ELC.
Ford 6.0L Power Stroke Diesel :: Radiator Removal To Do Oil Cooler?
I thought I remember a posting about removing the radiator to do the cooler because it made it easier to work standing in the engine bay with the engine in front of you instead of leaning over and removing everything from outside ? I'm getting ready to do my 4th external oil cooler? And is it difficult to remove radiator, and/or worth removing it ?
View 14 Replies