Ford 6.0L Power Stroke Diesel :: 2006 - No Start Intermittently / Slightly Low Compression On One Cylinder
Started having some crank no starts intermittently. Scanned and found codes for cam sensor. so I was in a pinch and a hurry on a sunday so I picked up a BWD brand cam sensor from parts store and installed. I have not seen this issue since but started noticing other thing going on. I noticed a few weeks ago my truck was starting a little strange. as it would spin over before firing off, it didn't sound right. I couldn't pinpoint if it was due to slightly low compression on one cylinder or one cylinder had a little fuel or oil in it and that one cylinder was actually firing while cranking over.
I also was noticing a little longer crank times than normal. didn't matter if engine was cold or hot. sometimes would fire up quick and sometimes it took a few seconds. most of the time I couldn't catch it on my scanegauge if the ICP was low due to the lag on the scangauge.
Well one day on my way home from work (50 miles one way) I stopped about half way to fuel up. after filling up and attempted to restart the truck it really acted like it didn't want to start but did after cranking for about at least 10 seconds and started rough. and of corse my scangauge decied to hate me this day because it would show any data until I unplugged it and plugged it back in. so started home. felt like it had a very very light miss on the way home. when I slowed down to turn onto my road the truck died. took forever to get it to start back up. this time the scangauge was reading and I could see ICP was between 300-400 and IPR was 85%. so low pressure and not reaching the 600 needed to fire. once it started I limped it home. scaned it with my Auto Enginuity and it didn't show any codes.
So that much I can see I have a leak on the HPO system. but I done a lot of work to the truck about 2-3 years ago. roughly 80k-100k miles since the work. what I done included...
OEM oil cooler
OEM (updated)dummy plugs, standpipes & STC fitting
OEM head gaskets and ARP studs
BPD EGR cooler (I should have deleted)
ALL other engine gaskets(Bed plate, oilpan, front&rear cover, ect.)
OEM glow plugs and harness
OEM blue spring upgrade
Cleaned turbo veins
2 OEM REMAN injectors. (cant remember which two) had contribution codes one on each side.
This is all I can remember right now. Now have yall seen the updated dummy plugs and standpipes leak? I have not pulled valve covers to air test the HPO system yet.(don't have my air compressor at my new house yet). Here is what I have done so far:
Fully charged batteries.
I did do a bubble test. pulled upper fuel filter cover off and removed filter topped the bowl off and turned engine over using the wire by the passenger side battery. some bubbles but not a bubble bath.
Checked fuel pressure (not running) its 60psi. did not start truck because I need a different fitting so I can run the truck and check pressure while running.
while doing the bubble test I could hear that one cylinder is low on compression. but I do not have any misfire or contribution codes.
when I ran contribution test on AE its not showing any particular cylinder lower than the rest. but the line is not very solid at all.
Here is what I plan to do.
Compression test on each cylinder.
Looking at the Harbor freight kit. Looks like it has fittings for glow plug and injector holes.
If I can do compression test on both glow plug and injector holes this should show weather my injector orings are the cause of the low compression.
Then I have to airtest the HPO system and find the leak.
Am I on the right track? what else should I check? Guess I should add that the truck currently has 297K miles.
Ford 6.0L Power Stroke Diesel :: 2004 F250 Running Rough Intermittently
Ok, so I have a 2004 F250, with 6.0L. when driving at a steady speed (doesn't matter what speed), the engine will run rough when coming to an idle, and stay running rough until I shut it off and let it sit for a bit.
After I cycle the key a few times it will fire up and run fine, so I came to the conclusion that air is getting in the fuel system. I then took the filter cap off that is located in the engine bay and cycled the key, which produced a lot of bubbles, which I am assuming shouldn't happen.
I guess my question is, should I have air bubbles in the filter bowl, when cycling the ignition?
Ford 6.0L Power Stroke Diesel :: Intermittently Running Rough At Idle - Code P0269
So my truck is intermittently running rough at idle for the most part and sometimes slightly loses a little power while driving down the roads. Seems to run worse as it warms up. When it runs rough it sounds like a cylinder is missing. The truck is throwing code P0269 for Cylinder 3 Contribution/Balance. Smoking isn't horrible coming out of exhaust but it's there and it comes out at a constant rate. The injector has been replaced by the previous owner recently. It has an egr delete, new turbo, ficm, ficm harness, HPOP, and stand pipes.
When I put the starter solenoid wire to the battery you can hear the engine skip. I did a compression test on cylinder 3, put oil in the cylinder and did the test again to find that I still didn't have compression. Assuming that this was an issue in the head I had my doubts that it was a bent valve and it could have been a bent pushrod.
Sure enough I found the intake pushrod for cylinder 3 was bent slightly so I replaced the pushrod. I started the truck again and seemed fine at first but just like before it started to run worse as it warmed up.
I was able to drive it to the gas station real quick to fill it up on fuel and drove back home which is a short drive, but the truck was running worse and worse and it eventually died on me. I attempted to start and had to jump start from my other truck and the 6.0 would not start. I ended up frying the starter trying to start it so I'm taking a break from it for now.... Ended up pushing the truck home.
The only thing I can figure is that I don't have oil pressure in the oil rail which is why it died but I don't understand why the truck still ran rough and pulled up with the same P0269 code....
Ford 6.0L Power Stroke Diesel :: No Start - Running Rough?
Well, I've read a lot of threads on this problem! Try to do my own repairs, so I'm learning and not spending a lot of cash at repair shops.I have an 04 6.0 Super Duty Crew. Starting running rough on way home. Pulled over ,then it died.wouldn't start. Had towed home. Replaced ficm circuit board. No start. Replaced Harness,
icp...... ipr Sensors. Still no start. I noticed there is another circuit board inside ficm. Should I have bought the whole ficm unit?
Ford 6.0L Power Stroke Diesel :: Running Rough / Stalled No Start
I was towing a trailer about 600 miles truck was running great, pulled in for fuel and truck was running rough, refueled and was on my way then when going down a hill (Idle) it just quit, had to tow remaining 200 miles.
After reading the forums I replaced the ICR (ICR screen was damaged) Truck now starts but its very loud and missing like crazy. and surges if i give it a little gas. codes 0268, 0281, 2284, 2288 I also replaced the ICP.
should I replace the injectors? what causes this?
Ford 6.0L Power Stroke Diesel :: 2007 F350 Not Starting - Running Rough - FICM?
I just bought a 2007 F350 6.0 two days ago, so I was giving the truck a good wash today using a electric pressure washer. The engine bay was pretty dirty so I decided to take some soap and a brush to it. After cleaning it I let it sit for a while in the sun to dry. (engine was stone cold). After it had completely dried out I go in and it cranked right up. I let it idle for a good minute-minute and a half put it in drive and pulled away slowly, right when I touched the accelerator it started running rough, so I popped it into neutral and let it idle for a sec but it was still running really rough so I cut it off not wanting to damage anything worse.
I let it sit and tried to start it again, it just turned over and over. I checked the oil level it was good. So I pushed it back into my driveway to figure it out. I took ICP connector out and tried to start it, just turned over and over. took fuel filter out it was just replaced 2K miles ago it looked a little dirty but not super bad. I put that back in. took icp out again and tried to start it and it started but ran super rough and was dumping black smoke out.
I checked back all ficm connectors and they were all connected. I haven't checked the voltage on that yet, but plan to do that tomorrow. the previous owner had the ficm go bag about a year ago and he sent it off to ficmrepair.com and they fixed it for him. also he had the stand pipes and dumby plugs done as well as the stc on hpop. im kinda at a loss on where to go now other than to check voltage on ficm.
Ford 6.0L Power Stroke Diesel :: Truck Will Start Running Really Rough After Filling Gas Then It Will Clear Up
I have an 04 F2 50 with 6.0 with approximately 225,000 miles. I filled up with gas last Wednesday and every so often the truck will start running really rough and then it will clear up. Is it possible to of gotten some bad gas if so what products are out there to clear that up. Could've been injector going bad what are the best products for cleaning injectors. No check engine light on, gauges are good, nothing different on the scan gauge.
View 3 RepliesFord 6.0L Power Stroke Diesel :: Running Rough After Putting Fuel In Truck Now Won't Start
This has me puzzled to no end. After my son had put fuel in my truck it began to run rough, and had to be towed home, and now won't start. Now the first thing I thought was that he put regular gas in. But he was sure he had not ,and the receipt from the pump indicates diesel. It was hard starting before this happened.
1st Misfortune of having gas put in instead of diesel and did your vehicle run afterwards.
2nd Here are my readings from my scangage:
Sync Yes/1, Ficm main power 48.5 v, ICV .17 (2.01 when cranking). ICP 1572. IPR 50.7.
Checked upper fuel filter for bubbles, none.
Engine oil pressure comes up immediately on cranking.
Don't know what else to check, these readings look fine to me. Only the fuel is something I'm not 100% sure of. It does smell like diesel not gasoline.
Ford 6.0L Power Stroke Diesel :: Dies Intermittently While Running?
Dies while driving down the road and usually will restart with no problems.Seems to happen more often when it gets hot out. IPR/ICP are good.It took a long time to start once also. I'm leaning toward fuel pump but ?
View 14 RepliesFord 6.7L Power Stroke Diesel :: Running Rough / Reduced Engine Power
I am having a problem with a 6.7. The truck has 9900 miles on it. It has a dpf delete, egr delete, Spartan tuner and a snow stage 3 kit. The truck lopes at idle but once throttle is applied it levels out but still runs a little rough. Its keeps saying its in reduce engine power no matter how many times I clear the code. If I clear the code it will come back in 2 seconds with out cranking the truck or anything. Rail pressure is telling me 31090 psi and not changing running or not. I have changed rail pressure sensor, and pressure control valve with no result. The green and violet 5 volt reference that feeds those sensors is only putting out 1.2 volts. Put a new pcm in it still the same and now has quit running totally. The codes are P0193, P0335,and P06A6.
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2005 F350 Running Rough - No Power To Move
I got a 2005 f350 6.0 deleted and studded with air dog 2 4g pump, 125k miles. It started running rough then just died all within a few miles tuner showed code for injector 6 and ficm towed into ford dealer didnt have time to mess with it. They said ficm was bad had them replaced it then they said i need whole new fuel system lines,harness,pump,sending unit ,tank the whole 9 yrds. Which i thought was uncalled for so i called up airdog which system i had on there and they laughed and said ford garage is full of bs that they will upgrade my pump to the 4g and new harness.
So I took that stuff to garage had them swap it out and now they said come get the truck they wont work on it anymore that now it needs 3 injectors and they wont touch it with aftermarket fuel system on it. So I go to drive it home and it starts but runs rough and u can hold it to the floor and it wont budge bearly idles up and builds no boost my tuner is showing injector 2,3,4 now which wasn't a problem before i took it into the garage. So im not sure what happened to cause this all to happen but before i sink any more money into it is the 3 injectors enough cause to make it not build boost now .
Ford - Windstar :: 1998 - Start Running Rough If Throttle Is Slightly Cracked
From cold, I start the van up, and if I just slightly crack the throttle it will start running rough. I think it goes away under heavier throttle...might just be that the rpms are up I can't feel it anymore, I don't know. It will idle just fine, and after it warms up it also seems fine. Where to look?Also I sometimes hear a very small, high pitched, vacuum leak from under the hood. What are the most common items that go bad, that I should look at first?
View 4 RepliesFord 6.0L Power Stroke Diesel :: Running Rough After Oil And Filter Change
Did my oil change last night and filter swapped both fuel filters on my 04 f350 started it up last night drove it a little bit and she was fine. Went to start her up this morning and she was pissy so I drove her a bit once warm and she feels like there is a dead cylinder maybe??
View 8 RepliesFord 6.0L Power Stroke Diesel :: Truck Got 4 New Injectors But Still Running Rough
My Excursion got 4 new injectors a couple weeks ago and when I got it back, it was running rough. My mechanic told me it was going to take about 100 miles for them to break in.
300 miles later and it is still running rough. So I opened the hood, took a look around and saw this wiring harness unplugged. Where it goes? Youtube video shows where the harness is [URL] ......
Also, my truck has been shaking violently at 50 miles per hour, unless I hit tow haul, then it is moved up to 60... I am assuming its connected some how to that wiring harness being disconnected.
Ford 6.0L Power Stroke Diesel :: Intermittent Rough Running At Idle
In your experience, what issues have you seen that caused intermittent rough running at idle, but did not throw a code. I have monitored (with numerous scanners/gauges) this 6.0, but cannot get a code or see any of the sensors out of spec.
At Hot idle:
IPR: 24.2
ICP: 640
ICV: 0.90
MAP: 14.7
MAF Volts: 1.5
EOT/ECT Deltas within 10 and Avg ECT=192, EOT=199
EGR Valve cleaned and EGR demanded = EGR Measured
Vehicle will run rough after long runs or towing. Cylinder Balance test showed all injectors on. What could be the cause?
Ford 6.0L Power Stroke Diesel :: Running Rough - CEL On With Code P2285
Wife just pulled in said your trucks running rough. Right out the gate went out Checked ICPV its at 0 KOEO... Noticed a CEL P2285...
ICPV seams to be Jumping all around at Idle...
it stutters and smooth's out some I believe its going into default mode...
its acting different then last time the ICP went south thinking a wire is shorted or that's my guess ...
is it just me or do Vehicles seem to break down more when its Cold...
Ford 6.0L Power Stroke Diesel :: Bucking And Running Rough Until Warmed Up
Truck is running bad when first cranked in the morning, is bucking and running rough until warmed up, think the oil needs to be changed and which additive is better the archoil or Rev x?
View 14 RepliesFord 6.0L Power Stroke Diesel :: Truck Running Rough When Cold
My truck was running rough when cold, I went to check the ficm voltage while wife was cranking and coolant shot right into the ficm and cooked the sumbitch. Stop laughing that stuff happens to me all the time. Anyhow, got a new ficm and truck wont start. Starter kicks out after a few revs. I ran my own solenoid wire to the starter and it cranks just fine. ficm at 48.5 koeo and cranking, icp 1100+, ipr from 14.8 to around 40%, ...
It takes a few seconds for the cam/crank to sync but it does. I changed the fuel filters and primed it, Got new batteries, and threw a crank sensor for s+g. With the key on and me cranking it using the solenoid wire, it almost starts. But from the key it will kick out after a few seconds. All fuses and relays are good. I hear the pcm also controls the starter, could that have cooked when the ficm went or would it blow a fuse? Diagnosing using a scangauge2 ....
Ford 6.0L Power Stroke Diesel :: 2006 F350 - Bucking / Rough Running
2006 F350 6.0 ... I am piling up parts for a bulletproof party later this summer. It has gotten grumpy ahead of schedule. I will hook up the AE tomorrow for consultation.
In the meantime. Running rough at 50. Seems to accelerate from a stop semi ok. Sitting at idle, holding rpm at 1750 I hear kind of a thump under the hood and the rpm drops 300, then slowly finds it way back to 1750 and it repeats itself.
This thump has not been noticed in the past. Could this be the VGT not working as expected?