Ford 6.0L Power Stroke Diesel :: 2004 F250 - EGR Low Flow Code
I am driving a early 2004 F250 CCSB with a 6.0l. I have a Code that is for an EGR Low Flow. I have a Scan Gauge II that I have been using to try and determine why this is. I have replace the EGR Cooler (unrelated), the EGR valve, and the MAF.
My EVD and EVM are tracking. My IA1 reads a letter (B usually) and 3 numbers that are in the 6 to 900 range. My IA2 appears to read normal with atmospheric temps at start up and goes up and down IAW the EVD and EVM readings. My FIA (already programmed) reads outside temperature along with the overhead console. The EBP reading doesn't exist, it is blank.
Ford 6.7L Power Stroke Diesel :: 2012 - Keyless Entry Master Code Location
The new to me 2012 dually has lost its keyless entry code card. I know on the 08-10 models you could look up behind the radio to see the code. Looking for physical location on the 6.7 family?
View 8 RepliesFord 6.0L Power Stroke Diesel :: 2004 F250 - Half Of Instrument Cluster Not Working
So, went to drive the truck (2004 F250 6.0, 145000 mi) yesterday and the right half of my instrument cluster was not working (tach, trans temp and water temp), CEL and check gauges lights on. My scan gauges gives me readouts of all 3, so I know the computer knows the right values. Pulled all three fuses related to the cluster, all looked good. All gauges, including those not working, did full sweeps with key on after putting fuses back, so I know they function. Also, the glow plug light stays on way longer than normal.
View 2 RepliesFord 6.0L Power Stroke Diesel :: 2004 F250 - Instrument Cluster Right Side Is Not Working?
My right side of my instrument cluster is not working. the Tachometer, Engine Temp and Trans Temp gauge are non responsive, and the CEL and Check gauge light is on. I have seen other posts with people that had the same problem but no solution to what fixed the problem. 2004 F250 Lariat.
View 4 RepliesFord 6.0L Power Stroke Diesel :: 2006 F250 - CEL Is Always On / Error Code P1102
6.0 diesel 83,000 miles. My CEL is always on and my Edge gauge says it's lower than expected Mass air flow. I've changed the filter, cleaned the MAF with special cleaner and then replaced with new. I've replaced the EGR valve.
If I clear the codes and run it I don't get a CEL until I turn it off. But the next time I start it, there it is again. My Edge reads 0.0-0.3 MAF while running but what that means. One end of my cleaner box is slightly warped but I can't feel any noticeable leakage.
Everything runs fine but I would like to regain the ability to have that idiot light available to tell me if I have a new problem.
Ford 6.7L Power Stroke Diesel :: 2011 F250 - P1635 Code Won't Clear
Bought a 2011 F250 with P1635 code. It has 35x12.50 tires my Sct x4 tuner only goes up to 34 inch tires. Im new to the 6.7 diesel game previously had 6.0 and want to hear from yall what to do.
View 1 RepliesFord 6.7L Power Stroke Diesel :: 2012 F250 - TPMS Fault Code
I just bought a set of 2013 20" rims for my 2012 F-250. I can't seem to get the tire fault light to go off. I've gone through the "learn" process but it won't read them. Are the TPMS not the same between years?
View 2 RepliesFord 6.7L Power Stroke Diesel :: 2011 F250 - CEL Code P2479 For EGT Sensor
CEL came on today on my 2011 F-250 6.7 with 48K miles. It did not show a message or shut down. When I checked the code it was P2479 EGT Out of Range Bank 1 Sensor 2. I was reading about a letter last year, which I did not receive, concerning an extended warranty. My questions are: What is the part number? How are they identified and located in the exhaust system? I found a diagram stating: EGT 12, 14 ect? How does that correlate to Bank & Sensor?
View 13 RepliesFord 6.0L Power Stroke Diesel :: 2006 F250 Won't Start - ICP Is Low - Code P0231
I got a 2006 F250 6.0 that won't start. It turns over perfectly. What I've done so far was change oil and filter, along with fuel filters. All fuses and relays are fine. I payed for the scan gauge 2 and monitored FICM SYNC, FICM voltage, ICP, AND IPR. Every thing checks out besides ICP. The ICP is reading under 400. So I unplugged the ICP. Still no start.
I decided to spray some starter fluid in the intake and turn her over. Boom starts right up and runs fine. I even drove her around for about 20 min. I get home and shut off the truck. wait a few minutes and nothing dead again. So ICP is low but the truck runs fine after some initial support from starter fluid. What I need to do next? I don't want to have to take it into the shop for something stupid I could do myself.
Also the code its throwing at me is P0231 Fuel Pump Secondary Circuit
Ford 6.0L Power Stroke Diesel :: 2007 F250 - Upfitter Switches Not Working?
The lights are on on the switches themselves, I used the red pass through wire under the hood and then connected it to the Orange w/ blue tracer upfitter wire( I think #4 switch) and it has no power. Changed the fuse and still nothing??
View 13 RepliesFord 6.0L Power Stroke Diesel :: 2003 F250 - A/C Compressor Intermittent Working
I have a 2003 f250 6.0. Recently, I have noticed that my air conditioner will work at first but once the compressor cycles off it does not come back on. I end up having to turn the a/c controls to off and wait about 5 min then turn them back on and it will work for a about 5 min then blow warm air again.
This happens more when towing rather than just driving around. I have changed out the sensor on the canister but it was no dice. The system is charged to the correct level according to my gauge. This occurs more often on hotter days than any.
While the truck has been running and the system is malfunctioning, I have crawled under the truck and noticed the center wheel of the compressor is not turning but can be turned by hand. Do I need a new compressor or am I missing something else that would be simpler?
Ford 6.7L Power Stroke Diesel :: F250 - Windshield Wiper Sprayer Not Working
6.7L ... Just traded in my F250 on a 2011 F350 Lariat. Love it. Period. Except that my windshield wiper sprayers will not work. I don't hear anything when I hit the button. No click or motor running. I can't figure out what fuse it is because I don't have an owners manual.
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2006 F250 - Tachometer Not Working Properly
I have an 06 f250 6.0. When I bought it a few weeks ago I turn the key on and let the glow plugs warm up and start the truck it would start easily. Now it seems like it's taking longer to start . The temperature are between 50 and 80 degrees. I changed the fuel filters and it's still taking to long to start.
2nd I noticed today that when my truck is at idle the Tachometer is at 0 and when I'm driving 60-70 MPh it goes up to 900 or maybe 1200. It seems to be running fine no loss of power that I can tell. What could be causing the long crank time and my Tachometer problems.
the glow plugs and injectors are new I don't remember the brand and the fuel filters are brand new Motorcraft.
Ford 6.7L Power Stroke Diesel :: 2011 F250 - Diagnostic Mode Not Working
I've done it before but now when I try to enter into the diagnostic mode I'm not getting anything but the typical message center. I'm holding the down arrow button, inserting the key, and then starting the truck. No diagnostic mode. Am I doing something wrong? 2011 F250.
View 1 RepliesFord 6.0L Power Stroke Diesel :: 2007 F250 - Check Engine Code - ICP Circuit Intermittent
I have a 2007 f250 and got a check engine code icp circuit intermittent and to what I know icp sensor should be on the valve cover on the passenger side but it's not I bought the truck few months ago could it be that they swapped the engine for an early 6.0 or is there any other place for the icp sensor???
View 7 RepliesFord 6.7L Power Stroke Diesel :: 2016 F250 - Check Engine Light - Code P0170
I just bought a 2016 F250 with the diesel and thought I'd share an early ownership experience. At about the 1300 mile mark the check engine light came on and other than the remote start not working the truck continued to run great. I pulled a P0170 code, Fuel Trim Bank 1. And since the truck was still running fine, I considered clearing the code and see if it would come back. But since it's under warranty I decided to bring it to the dealer. They checked it out and diagnosed a bad Fuel Rail Pressure (FRP) sensor. They swapped it out and it seems to be good to go (no more light). While I was in there I asked them to turn on the DPF percentage full screen which they did.
View 3 RepliesFord 7.3L Power Stroke (1999-2003) :: F250 - Remote For Keyless Entry?
I have bought a used 1999 F250 4-door 4X4 7.3. Is there any way to tell if my truck came with a remote for the keyless entry. It has power door locks and windows. I was debating on calling my local Ford dealership and seeing if they could check by the VIN number.
View 7 RepliesFord 6.0L Power Stroke Diesel :: 2006 F250 - Code P0677 / #7 Glow Plug Circuit Module
06 6.0 F250 throwing code P0677 #7 glow plug circuit module. I don't think one bad plug would cause a no start, however coupled with too much oil possibly? Swapped my oil about 500 miles ago, I put in 20qts accidentally, drained off about 3-4 qts eyeballed, truck fired up and ran fine no smoke nothing. Yesterday morning I was leaving work and moved my truck from parking space to behind the bay at my fire station, I turned the engine off.
Loaded up my gear and turned the engine to the aux position and someone was talking to me so inlet it sit for a while in the auxiliary position. Went to crank no start, turned the key off then back on and it fired. Fast forward after 7 different starts throughout the day, I'm at dinner with my son we go to leave engine will not start at all, rolls and rolls and rolls nothing. Towed her home and scratching my head. Over filled oil with a bad plug cause no start??
Egr delete, new oil cooler, cat and muffler delete, upgraded Y turbo pipe. Also have an SCII throwing codes p0677 and p0401 egr code....
Ford 6.0L Power Stroke Diesel :: 2004 F250 - No Radio Or Power Windows
I have a 2004 F250. Owned it for a little less than 4 miles (186k on the odometer) .. The other day making a routine run and the radio goes out. Stopped to check it out and found I had no power windows either.
Made it home, checked the fuse on the radio and its good and the the power window fuse is also good. Put a meter on the terminals and have no voltage going to them. What I need to look at???