Ford 6.0L Power Stroke Diesel :: 2004 F250 Will Not Start At All
My husband and I purchased a 2004 f250 king ranch 6.0L... We love the truck, despite the headaches. We took it to a dealership and spent just under $5k in parts, drove it for a month (everything going great) until we shut it off to bs w a friend and it won't turn back on. It's been sitting for 4 days and nothing. Cranks and cranks, but won't actually start. We are pretty handy with gas trucks, but this diesel is out of our element- we are getting better though haha!
We looked on here and saw that the no start could be bc of the FICM - swapped it out- not the issue.
Now the codes being thrown are P2291 & P2285 (or so my husband says)
We are thinking if we replace the ICP and that fixes it, we won't need to do the HPOP. Or do we need to do it as well? Are we on the right track?
When we shut it off, it didn't have any lights on, no gauge fluctuations, or any "red flags". This is why we are stumped!!
(Ford dealership fixes: 2 batteries, new starter, new tank cap, new oil cooler, maybe a few others- receipts not infront of me).
Like I mentioned, we've already dropped more money than we have into this truck and now it's taking more- we love the truck and once it's fixed we will "have a new truck" it just sucks bc my husband works afternoons and I'm a stay at home mom with a 14mo and this is our only vehicle.
Ford 6.0L Power Stroke Diesel :: 2004 F250 - Crank But No Start
I have an early 2004 F 250 6.0 that just quit one day and haven't been able to get it started since then. I have tried to follow the No Start checklist...
I have no aftermarket mods or tunes.
I have changed the fuel filters, made sure that there is fuel in the tank and made sure that it is getting fuel.
I have un-plugged the ICP and still no start.
When I turn the key on it goes through the regular sequence and I hear the injectors (sounds like it's doing a buzz test).
When I try to start it, it cranks over, but I hear a good bit of clicking coming from the fuse/relay panel under the driver's side dash.
I have inspected fuses/relay and dont see anything smokingly obvious.
I installed new batteries, but no joy.
While trying to start, it sounds like it may actually do it for a second, and then I get a noise from the starter.
I bought a scanguage and added the PIDs that I found searching through the forum and here are my results.
ICP key on = 0.23 ICP while trying to start = 1.30
ICP Voltage (Volts)
TXD: 07E02216AD
RXF: 0462451606AD
RXD: 3010
[Code] ....
Camshaft & Crankshaft Sync = This is erratic; it will flash 1 and immediately go away. The thing is, I don't know which sensor should be replaced.
Ford 6.0L Power Stroke Diesel :: 2004 F250 - No Start After Replacing IPR
The truck is a 2004 f250. Build date is 7/ 03 so its an early 04. I have been in a parking lot for 3 days now with no money trying to get this truck to start. Me and my dad replaced the ipr pigtail and the ipr thinking this might have been the problem, because the ipr pigtail had a damaged connector.
Before doing this work the icp sensor connector had no oil in it, now after replacing the ipr and cranking the engine the icp has some oil in the connector, could this cause a short and not let the truck start, and if so will unplugging the icp allow the truck to start?
We were having trouble with no starts before this happened and when it did all we had to was push the ground wire back further that goes back to the ficm and the truck would start, but that is not working anymore.
Is it possible the ipr is not seated properly or the new ipr is bad out of the box? Or maybe the made in tawain pigtail connector to the ipr is bad?
We are thinking it may be a short somewhere in the harness since everytime we pushed the ground to the ficm up further to where it grounds before when we had no start problems this might have took the short out of the ipr or icp pigtails and allowing the truck to start. Injectors are buzzing when key is turned and I can hear the fuel pump.
Ford 6.0L Power Stroke Diesel :: 2004 F250 Losing Power Then Stalled Out And Wouldn't Start
this morning I started my 2004 f250 drove a mile and filled up my truck. Then drove another mile and my truck acted like it was running out of fuel. It was loosing power then stalled out and wouldn't start. About five hours later I tried to start it again and nothing. about five hours after that I tried it again and it started up and drove fine.
My thought was fuel filter or the water trap. I haven't had a chance to open the filters up and check them yet. Today while I was at work I got on here to see if I could figure out what was wrong with it. all I could think of was maybe the HPOP went out or the ICP sensor. Could one of these be the problem or was I right with my original thinking and it's just a fuel filter? First thing in the morning I'm going to pull the filters and replace them.
Could there be something else wrong with my truck that I don't know about? Like I said I filled up the fuel tank then it lost power within a mile and stalled out and wouldn't start back up. Then about 10 hours later it fires up and acts like nothing happened.
Ford 6.0L Power Stroke Diesel :: 2004 F250 V8 - Hard Start / Rough Idle / Shaking - No Power When Cold
I'm new to diesels. I just bought a 2004 F250 with the 6.0 V8. I have the high and low circuit, contribution codes on cylinders 4 and 8. I've only had the truck for a few days but I've been reading a ton. The symptoms are hard start, rough idle/shaking, no power when cold. When it heats up and I'm over 2000 RPM it seems to be just fine. Even when hot and below 2000 RPM it does ok. I've check the FICM. It reads 48V with key on and 48V running. My plan is to do the following:
Change the Fuel Filters
Change the oil filter
Change Air Filter
Change oil with 5-W30 synth and I have both Hot Shot/Rev-X
If that doesn't work, I'll replace the two injectors. How does that sound.
Ford 6.0L Power Stroke Diesel :: 2004 F250 Does Not Start / No Buzzing On Injectors When Key Turned On
I have been having trouble w my 04 I checked all fuses all relays all dash lights work, no buzzing on injectors when key turned on. I checked push pull plug for starter it turns over with direct to battery but still does not start. New computer on fender.
View 2 RepliesFord 6.0L Power Stroke Diesel :: 2004 F250 - No Start After Fuel Filter Change
I have a 2004 F-250 changed out both fuel filters and now can't get it to run. It will start up and run for about a minute then stall out. I have cycled the key/pump numerous times with no luck. When I look into the fuel bowl when I engage the pump it looks like it's pushing more air rather than fuel. It seems to be burning the fuel in the bowl and then stalling out. When I take the bowl cap off after it stalls it's empty.
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2004 F250 Stall After Start When Backing Out Of The Driveway
I have had literally no issues with my 2004 F250 Super Duty. Went out and started the truck like every other time for the past 13 years. Started backing out of the driveway and burped the throttle and it just quit??
I put back into park and it rolled over for about a minute and finally caught. When i put it back into gear i had zero throttle response. I have a NOx sensor fault code and and EGR fault code. I replaced the FICM 2 years ago.
Ford 6.0L Power Stroke Diesel :: 2004 F250 - Hot No Start - Temp Gauge Maxed Out
So I recently bought a '04 F-250 early build with the 6.0 powerstroke. Truck drove fine for the first 1000 miles. Drove from Fort Hood back home for leave. Got home and truck sat for two days, started it up and it ran for 15 minutes, then shut off on me. Temp gauge read normal, but after it shut off, I turned the key off and back on and temp gauge was maxed out. And truck has to cool down before it will start again. Replaced the IPR Sensor to no luck. Not sure if I have an ICP sensor issue or what it could be.
View 11 RepliesFord 6.0L Power Stroke Diesel :: 2004 F250 Stalling / Loss Of Throttle Response And Won't Start
2004 F250 Powerstroke Diesel 6.0L ... 90,xxx miles
Symptoms : Within the past 10,000 miles the truck has begun exhibiting the following problems, sometimes in conjunction with one another and sometimes just independently of one another:Stalling on the road at low speed / low engine RPM.
Throttle pedal becomes completely unresponsive. Stabbing the throttle pedal repeatedly sometimes causes it to return to operation. Sometimes the engine must be shut off and re-started to return throttle pedal to operation.
Rough, surging, stumbling idle at rest. Will crank but not fire occasionally. Problem has become worse as of late. Repeated attempts at starting the engine usually result in success after much, much retrying.
Work Done : Local Ford Diesel technician replaced the EBP sensor, replaced the EGR valve and re-flashed computer with latest software -- all under warranty. Problems still persist.
Peculiarities : We have tried driving the truck with the EGR valve disconnected and with it connected, both at the technician's request.
With the EGR valve disconnected the truck usually starts fine but still stalls out at low RPM / low speed. Fuel economy is also cut by nearly 50% with the EGR valve disconnected. Really couldn't afford to keep driving the truck like this.
Technician speculated that if the truck continued to die with the EGR valve unplugged, it meant that the computer or fuel pump might be bad. ????
It also seems that the stalling problem manifests after the truck has been driven at highway speeds (65-70mph) for at least a period of 20-30 minutes. Stalling usually happens as soon as we make an exit off of the highway and begin to slow down to make exit. As in foot off the throttle pedal. Engine RPM drops then stumbles then stalls.
I wonder if this is a problem with the HPOP or ICP system.
Specifically I wonder if this is a cracked quick release fitting that allows oil pressure to fall after the engine heats up and oil viscosity thins out with the heat. Once the engine cools down sufficiently to thicken the oil, the HPOP finally gets enough oil pressure to allow the engine to fire up again.
Ford 6.0L Power Stroke Diesel :: 2004 F250 - Glow Plug Fault - Hard To Start When Cold
I'm new to owning a diesel. I have a. 2004 f250 6.0. I gotta smog the truck this weekend but the check engine light is on. Fault is P0674. I've notice during the day it starts up fine but at nights, lately it's been low 40 outside it won't start. Where to start at.
View 3 RepliesFord 6.0L Power Stroke Diesel :: 2005 F250 Sometimes Won't Start When Hot
I have an 05 f250 with 109k. Recently I turned off my truck, waited about 45 min or so and upon returning the truck would just crank and crank with no fire. After waiting about 4hrs the truck started right up like nothing was wrong.
Yesterday it did it to me again. This time I have it a small shot of starting fluid and it fired right up and ran like a champ all the way to the shop..... I got the call today from the mechanic saying I have 5 injectors that are bad, 2 glow plugs and harnesses. His quote was 2400 out the door.
Ford 6.0L Power Stroke Diesel :: 2006 F250 - No Start When Hot?
My 2006 F-250 6.0PSD has a new hitch. Tonight it would not start once hot. It cranked and cranked but no start. My scanner showed ICP readings of 366PSI during cranking. Far below the 500PSI needed before the computer will fire the injectors.
So is this the STC fitting at the HPOP that is failing? If so how long will she start cold and drive normal before she leaves me stranded? I have the fittings and new dummy plugs and stand pipes as well. I was waiting to to do this work until I had the money for an new EGR cooler and oil cooler.
I know my oil cooler is failing as my deltas are showing a 15-19 degree spread over my coolant temps.
Ford 6.7L Power Stroke Diesel :: 2011 F250 Won't Start After Getting Reduced Engine Power Message
I have a 2011 Ford F250 6.7 Powerstroke. It has 107,000 miles on it.
The other day I was driving it down the highway and it got a Reduced Engine Power message on the dash. It lost power and I got off the highway to the service road. Then it died on me.
Had to get it pushed to a station then towed home. It wouldn't start. The starter cranks over for a few seconds but engine won't start. Checked all the fluid levels and batteries. My DEF fluid was only a half gallon low.
What I have noticed is that the DEF level indicator hasn't reminded me that it was low for over 4-5 months now. I had been putting in about 2-3 gallons every 3 months or so. But it hasn't reminded me lately and I just forgot. This is my first diesel.
Ford 6.7L Power Stroke Diesel :: 2011 F250 Crank But No Start / Reducing Engine Power
My 2011 6.7L F250 Superduty died on interstate the other night. Picking up throttle pulling onto interstate when a message came on the dash "reducing engine power" and the truck died. It will crank but will not start. It will start on ether but dies when that runs out. Has the following codes... p1249 Wastegate control valve, p0087 fuel rail/system pressure too low, p1291 & p1292 injector high side short to ground or battery (bank 1 & 2), p2291 injector control pressure too low-engine cranking. The codes are telling me I don't have enough fuel pressure but scan tool says I have 4000 w/ key on and 6370 while cranking and I thought 5000 was the pressure needed.
View 9 RepliesFord 6.0L Power Stroke Diesel :: 2005 F250 - New HPOP And No Start
I got a problem with my Ford F250 6.0 Diesel. The truck got a new HPOP but still wont start. ICP show everything between 15 und 75 PSI, it raises to 75 PSI max during cranking. The IPR shows 84,75% during cranking.
We get the code P0270 and P2285 in exchange but never together. We already checked the FICM but it looks good on the inside. I now ordered a new ICP sensor....
Ford 6.0L Power Stroke Diesel :: 2006 F250 Won't Start / No Cranking
I have a 2006 f250 superduty 6.0. The truck ran fine a week ago and than died as I was going to take it for a drive. I figured out that the fuel pump (air dog system) was not working. I fixed that and primed the pump. The truck still won't start. When it first happened the truck would crank but not start. Now all I hear is the starter but no cranking. Both filters could be replaced. The bowl to the upper is dry when I take the cap off. However fills up when you turn the key on. I'm not sure what else to try and I need to get this truck started.
View 3 RepliesFord 6.0L Power Stroke Diesel :: 2006 F250 - Smoke At Start Ups
I have a 2006 Ford F-250 6.0 powerstroke with 100,000 miles and it puts out a puff of smoke at cold start up every time and also when I run it then park it for maybe 1 1 1/2 and it puts out a puff and also I noticed when I get to work with is about a 20 minute drive I get there around 8 then leave at 5 I noticed it puts out a puff then if I watch the exhaust I can see a slight haze but I figured it's just condensation.
Here's the list of stuff I have put on the truck... Oringed heads by librator performance, with oem gaskets every thing, arps head studs, egr delete, airdog 2 fuel system,mtw stage 2 turbo, bulletproof ficm,coolant filter, banks intake, fuel pressure set at 68 and fuel regulator return.
Here's a list off parts I put on trying to fix the smoke I put in 5 injectors because the ford ids had a slight change and after that it was straight line I put in hpop and turbo drain pipe and I tested the ficm and its 48 with the key on and cranking and running...
Ford 6.0L Power Stroke Diesel :: 2003 F250 - No Start After EGR Delete
Just did an egr delete, oil cooler, icp sensor and exhaust on an 03 f250 6.0l. got it all back together and it cranked up and ran for about 30 seconds then stumbled and died. read to pull out the ipr sensor and check it and it had a piece of debris on it covering the screen. took of the debris and still no start.
View 6 Replies