Ford 6.0L Power Stroke Diesel :: 2006 - No Start Even After Sprayed A Little Starting Fluid
Ok the icp .hpop.ipop.crank ps and ficm is all good but still no start. I've sprayed alittle starting fluid and still don't start idk what else to do this truck is driving me up the wall it's been down for 2 weeks.
View 5 RepliesFord 6.0L Power Stroke Diesel :: 2003 - Won't Start - Crank Until Battery Died?
My 2003 f-250 6.0l has not been starting. I have connected a scan tool and I am getting around 1000 psi icp. The FICM voltage is 47.5v however when I cycled the key it dropped to 43.5 then started climbing to 48, but I am not getting FICM sync. I does eventually start when I do get sync. It seems to run fine after it starts. It does not do this all of the time. But this morning It cranked until the battery died. New FICM?
View 6 RepliesFord 6.0L Power Stroke Diesel :: 2003 - Died On Signal - Changed Injector ORings Still Won't Start?
2003 6.0 psd owned two years driven 2 months due to money thrown prior to forums and scangauge 2. Bought truck in chicago drove home. Oil in coolant. Did egr delete oil cooler all gaskets orings etc. New oil filters motorcraft fuel filters .new rad fluod wix trtmnt. Truck started right up. Still had same intermitantstudder as always when cold. Always exp those sysyems until hot then here and there until parked then hot no start or hard long start when hot. Knew something was wrong and waited for it to come to a head well it did in may.
I was driving coming up to a stop sign and truck died like i shut key off. Refired once off ether. Lasted 3 seconds died no restart period didnt even want to just crank crank crank.
ok towed truck i thought it was injector orings. Changed them still nothing . New icp. New cpm. Now have icp of 66 to 120psi cranking.ipr 14.40 koeo up to 84 when cranking. Ive unplugged just get eratic reading ipr stays same. Checked ficm 47to47.5 cranking and koeo. No codes beside for my egr delete and when i unplugged icp. I've been tinkering on this truck for a couple years now still lost bit getting better. I now have driver valve cover off . Its a 2003 .
Ford 6.0L Power Stroke Diesel :: Overheated And Died - Now Won't Start?
Left the cap off my degas bottle after checking it this morning. Drove a couple hundred miles and it overheated and died. Cooled it off, filled it up with water out here, now it won't start.
When I first tried, before I got it full of water, it barely cranked. Now, it cranks fine, even sounds like it cranks too fast. But nothing. Did I really blow it this time? I don't have my ScanGuage.
Strangely, the oil pressure gauge registers normal as soon as I turn the key on, and stays there while cranking. I'm used to them starting at O, then registering after cranking a few seconds.
Ford 6.0L Power Stroke Diesel :: Crank And Start Sometimes Then Just Died When Put It In Drive
Today I was driving my 04 f350 6.0 I got to a red light when it turned green I hit the accelerator and it would not go it would only go about 10 so I limped to a parking lot and it shut down, it will crank and it sometimes Will start but only rev up to a grand then put in drive and it dies I had someone run me out a new pre programmed FICM and I replaced it right there and still will crank but won't run so I had it towed to a ford dealer and dropped my key in the drop box, what it may be?
View 11 RepliesFord 6.0L Power Stroke Diesel :: Died Going Down Highway - Now Won't Crank And Start?
Truck died going 50 mph and would not restart. I turn the key to run and nothing. I can hear the injectors buzzing but it will not turn over or crank. I can jump from the battery and the truck will crank. However, it seems to be in limp mode. It will start off in 3rd gear and won't shift gear Tow/haul light is flashing.
The wire harness that goes down to the fan clutch is chewed up and frayed so I'm assuming that may have caused an issue. But i have unplugged the sensor to the fan clutch and it still won't start. I can hear the injectors buzzing but when I turn the key to crank it, it does nothing. Just clicks. I've cleared the codes and these keep coming back.
Ford 6.0L Power Stroke Diesel :: 2004 F350 Just Died Now Won't Start
M buddy's truck just died and won't start. So far we have changed the ficm because the voltage would fluctuate down to 25, the ficm harness as it was chaffed through and bare wires touching each other, both fuel filter, tested the alternator, new batteries, new air filter and bubble test. The truck spins over and tries to go but won't. I have also tried starting it with the icp disconnected with no change. The secondary filter had lots of bubbles coming into it while filling it for the bubble test, but we did that a few times and no more bubbles. When trying to start you can sound fuel flowing through the secondary filter, is this normal? While trying to start there is black smoke coming out of the tail pipe. We have also tried leaving it plugged in over night and no go.
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2006 - Died Now Crank But No Start
My wife and I went on vacation for our anniversary and the truck ran fine for a while then we went back to get ready and when we left it started up and everything seemed fine but it died about 200 yards later and is now cranking but not starting. Left my toolbox at the house (stupid!) And truck is new to me so I don't have gauge or reader. Checked the fuel filter under the hood and fuel pump is pumping. Any other tips on what to do that could be the problem without buying parts?
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2003 - Lost Power With Smoke Then Died - Now Nothing?
I have a 2003 6.0 when it has having troubles trying to cut out when running low rpms but would throttle out of it then it lost all power cab filled with smoke and died now it does nothing won't even try to turn over everything under the hood is covered in soot I'm ready to pull the cab just wondering if I didn't loose any oil or coolant...
View 6 RepliesFord 6.0L Power Stroke Diesel :: No Start / Cranking And Large Pop Noise Came From Under The Hood
Had Just replaced glow plugs and batteries along with a new set of tires. Truck had been running fine for the three days that is was. Went out the next morning and went to start and "POP" a large noise came from under the hood. I have yet to discover where this noise particularly came from or what it may have been that caused it. But ever since the POP it will not turnover what so ever. Key on every thing is normal all power just when go to turn key over it makes a faint click. You can feel the click in the relays on your hand when you try to turnover. But nothing. I am absolutely clueless.
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2006 F250 Died While Driving And Won't Start
While driving uphill yesterday, my truck 6.0 f250 completely died. Added oil cause it's been a while and tried starter fluid. Cranks but won't start. Pulled OBD codes p0300, p0304, p0401, p0460, p0562, p0606, and p2290. Checked IPR, works fine. Checked fuses. Low voltage codes are most likely from battery dying during the test.
View 2 RepliesFord 6.0L Power Stroke Diesel :: 2004 Truck Died While Running / Won't Start
Last friday, my truck died while running. I let it sit for a few hours, went out and it started right up. Went to get pizza for my kids and I got 5 blocks from my house and I barely had any power. Truck died again while getting pizza and had to tow it home. Now it will not start. I have checked fuses, taken apart the fuel pump on the motor and cleaned the water from it, added a fuel treatment and also did an old truckers trick with the fuel (10% gasoline). the truck will crank and make an attempt to fire but it will not start. I have 3 kids and this is my ONLY transportation. I need to get this thing running STAT.
View 1 RepliesFord 6.0L Power Stroke Diesel :: 2006 Truck Died On Highway / No Start
My truck died a few weeks ago on the highway had the hpop ipr valve and screen replace ran awesome for 2 weeks, shut it off ran into the store and it wouldn't start gave it a couple hours finally fired, started good the next 5 times go to start it the other day no start again, tried again 30 seconds later and starts trucks a 2006 with 226000km throwing no codes, I'm ready to go trade it off on a new one, where to start?
View 9 RepliesFord 6.0L Power Stroke Diesel :: Truck Died As Driving Down The Road Now It Won't Start
I have a 06 f350 with 140,000mile and today I was driving to a buddy's house and the truck died on me as I was doing 45mph so I towed it home and check the codes I have 1 low icp pressure and 1 low icp during starting / cranking and 1 ckp out of range I think that how it's worded so I looked at the icp pressure and it's 0 and the desired is around 1000 and the volt is .56 and as far as the ckp the rpm are reading so I don't know what to do about that ? Could the STC fitting and dummy plug and standpipe o rings really go out on me like this ? Or am I missing something? I am also trying to track down a oil pressure gauge for the Icp fitting to check it
View 9 RepliesFord 6.0L Power Stroke Diesel :: 2007 Truck Won't Start / Died While Driving
I have a 07 6.0 that won't start it died a few weeks ago while driving. Being a mechanic I've done numerous things to the truck in order to fix all the common 6.0 problems but can't figure this one out. It will crank and get oil pressure and fuel pressure but seems to not be getting fuel. The IPR valve isn't clogged I tried with 2 working valves nothing worked. Along with changing the ficm. The connections to the ficm are clean and all in tact. I have an edge evolution chip that isn't even showing any codes. Not sure what to try next since I don't have any codes to go off of.
View 11 RepliesFord 6.0L Power Stroke Diesel :: 2004 - Truck Died While Driving - No Start?
My wife was driving through the intersection when the truck died... Tried to start it again but no go, I had it towed home, and stared to troubleshoot.
I have a Scan gauge2 and these were the readings: FMP: 47.5, IPR: 84.71, SYC: 1, ICP: 0
I pulled the IPR (that was only a year old) and the screen was perfect. I had 11.5v at the plug for the IPR, and on the Ohms scale I was reading 1.8Mohms.
I went to the dealer and got a new IPR, and still no start. and the only change in the reading on the scan gauge was the ICP is now reading 56. The gauge on the dash is reading normal oil pressure, but I haven't checked actual Low-end oil pressure.
Last month I replace the HPOP, and 1 faulty injector. Now I thinking wire loom, defective new IPR from the dealership or the new HPOP has failed.
Ford 6.0L Power Stroke Diesel :: 2003 F350 - Hissing Sound Under The Hood?
I have a 2003 F350 with a 6.0. I just finished replacing my HPOP (Adrenaline Pump from Diesel Site) and fired the truck up and its making a hissing sound from the rear of the motor back by the turbo almost sounds like a tire leaking and its loud enough to hear over the engine. The truck is running and idling good but it doesn't seem to be quite 100% when I step on it.
View 10 RepliesFord 6.0L Power Stroke Diesel :: 2006 - No Start When Died After Shudder - Code P2291?
I have a 06 6.0 no start . I was at a light felt a slight shudder went to take off felt another shudder and it just died. Changed fuel filters, unplugged icp no start still. No code at first now throwing p2291. Fuel pressure is at 62 when cranking. Hooked up air to the icp port and only heard air coming out of both valve covers inlets. Ipr was at I believe 60 to 65% when cranking. Little back round 2 years ago I did the whole sinister diesel top end kit and put the updated parts in. New o rings on everything that took them, new egr valve, standpipes and dummy plugs. On the injectors all new o rings and crush washers. I believe that's everything.
View 11 RepliesFord 6.0L Power Stroke Diesel :: Truck Died And Refused To Start - Code P0603
So I have been fighting an electrical issue off and on since I bought the Excursion and I am at my wits end!
Put in 2 injectors. 1 in November and 1 last week. Thinking that it would fix my P0603 and the missing issue I was having. Plus the truck tossed a code for #4 and #5 injector. According to a snap on scanner and my AE the injectors were bad. The missing issues are gone, but I keep getting a p0603.
Go back to the middle of May. Truck died and refused to start. I put a fuel pump in it due to lack of fuel at one point thru the no starts. Shop had it 2 weeks and replaced the Cam sensor. Truck has been spot on for the last month zero issues.
Fast forward to today! Hooked up the trailer and loaded my tow tune. Check codes before hand and have a P132b code. Look it up and is a multitude of things to check. Clear code, tune the truck and head out for the weekend. Sat in traffic for 95 minutes to go 13 miles to the highway I needed to get to.
Driving the truck I had zero issues, until I got off the exit ramp to the campground. During the 2 hour drive I monitored a few pids on the scan gauge to see how things were on the truck after the work. The following are driving down the road at 2k RPMS 70 MPH give or take 5 MPH.
boost 7.3
map 22.9
EOT 225
FWT 211
TFT 163
CPM .28
ICV 1.9
VGT 57
IPR 37.3
CVI 4-5 (fluctuates)
SYNCH went to 0 when it died.
Truck shuts off and restarts right away and keeps running. I get to the campground and hook up the tuner to the truck and I have 2 different codes. My buddy the KAM P0603 and a new one Crankshaft sensor Pos A/ I can not remember what the code # was.
So after dropping 1500.00 on the truck the last 2 months, I am at a loss. The shop I took it to was a new place for me and I was not impressed. The lack of communication, 3 scratches on the truck and saying the truck had a miss and they didn't look at the injectors at all.
The 2 options I have are 45 miles away or 100 miles away. After today I believe it is an electrical issue and would rather spend a weekend of my time trying to find it. Where are the known chaffing points on the 03' 6.0L.