Ford 6.0L Power Stroke Diesel :: Truck Died As Driving Down The Road Now It Won't Start
I have a 06 f350 with 140,000mile and today I was driving to a buddy's house and the truck died on me as I was doing 45mph so I towed it home and check the codes I have 1 low icp pressure and 1 low icp during starting / cranking and 1 ckp out of range I think that how it's worded so I looked at the icp pressure and it's 0 and the desired is around 1000 and the volt is .56 and as far as the ckp the rpm are reading so I don't know what to do about that ? Could the STC fitting and dummy plug and standpipe o rings really go out on me like this ? Or am I missing something? I am also trying to track down a oil pressure gauge for the Icp fitting to check it
View 9 RepliesFord 6.0L Power Stroke Diesel :: 2007 Truck Won't Start / Died While Driving
I have a 07 6.0 that won't start it died a few weeks ago while driving. Being a mechanic I've done numerous things to the truck in order to fix all the common 6.0 problems but can't figure this one out. It will crank and get oil pressure and fuel pressure but seems to not be getting fuel. The IPR valve isn't clogged I tried with 2 working valves nothing worked. Along with changing the ficm. The connections to the ficm are clean and all in tact. I have an edge evolution chip that isn't even showing any codes. Not sure what to try next since I don't have any codes to go off of.
View 11 RepliesFord 6.0L Power Stroke Diesel :: 2004 Truck Died While Running / Won't Start
Last friday, my truck died while running. I let it sit for a few hours, went out and it started right up. Went to get pizza for my kids and I got 5 blocks from my house and I barely had any power. Truck died again while getting pizza and had to tow it home. Now it will not start. I have checked fuses, taken apart the fuel pump on the motor and cleaned the water from it, added a fuel treatment and also did an old truckers trick with the fuel (10% gasoline). the truck will crank and make an attempt to fire but it will not start. I have 3 kids and this is my ONLY transportation. I need to get this thing running STAT.
View 1 RepliesFord 6.0L Power Stroke Diesel :: 2003 F250 Truck Just Died While Driving
I am working on an 2003 F-250 6.0l. The truck just died while driving. No restart. Plugged in my scan tool and I am not getting any High pressure oil. Is there anything other than the Hpop I should be looking at. I know it is a big job to replace the hpop so I don't want to overlook something simple.
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2006 Truck Died On Highway / No Start
My truck died a few weeks ago on the highway had the hpop ipr valve and screen replace ran awesome for 2 weeks, shut it off ran into the store and it wouldn't start gave it a couple hours finally fired, started good the next 5 times go to start it the other day no start again, tried again 30 seconds later and starts trucks a 2006 with 226000km throwing no codes, I'm ready to go trade it off on a new one, where to start?
View 9 RepliesFord 6.0L Power Stroke Diesel :: Truck Died And Refused To Start - Code P0603
So I have been fighting an electrical issue off and on since I bought the Excursion and I am at my wits end!
Put in 2 injectors. 1 in November and 1 last week. Thinking that it would fix my P0603 and the missing issue I was having. Plus the truck tossed a code for #4 and #5 injector. According to a snap on scanner and my AE the injectors were bad. The missing issues are gone, but I keep getting a p0603.
Go back to the middle of May. Truck died and refused to start. I put a fuel pump in it due to lack of fuel at one point thru the no starts. Shop had it 2 weeks and replaced the Cam sensor. Truck has been spot on for the last month zero issues.
Fast forward to today! Hooked up the trailer and loaded my tow tune. Check codes before hand and have a P132b code. Look it up and is a multitude of things to check. Clear code, tune the truck and head out for the weekend. Sat in traffic for 95 minutes to go 13 miles to the highway I needed to get to.
Driving the truck I had zero issues, until I got off the exit ramp to the campground. During the 2 hour drive I monitored a few pids on the scan gauge to see how things were on the truck after the work. The following are driving down the road at 2k RPMS 70 MPH give or take 5 MPH.
boost 7.3
map 22.9
EOT 225
FWT 211
TFT 163
CPM .28
ICV 1.9
VGT 57
IPR 37.3
CVI 4-5 (fluctuates)
SYNCH went to 0 when it died.
Truck shuts off and restarts right away and keeps running. I get to the campground and hook up the tuner to the truck and I have 2 different codes. My buddy the KAM P0603 and a new one Crankshaft sensor Pos A/ I can not remember what the code # was.
So after dropping 1500.00 on the truck the last 2 months, I am at a loss. The shop I took it to was a new place for me and I was not impressed. The lack of communication, 3 scratches on the truck and saying the truck had a miss and they didn't look at the injectors at all.
The 2 options I have are 45 miles away or 100 miles away. After today I believe it is an electrical issue and would rather spend a weekend of my time trying to find it. Where are the known chaffing points on the 03' 6.0L.
Ford 6.0L Power Stroke Diesel :: Truck Died And Coasted To A Stop - Theft Light Blinking / No Start
I was driving home tonight and stopped at stop sign. I took off and truck died and coasted to a stop. I tried to start but all it does is theft light blinks really fast and will not turn motor over. I tried to reset pat by following procedure I found on internet. Still no start. I then unhooked battery cables and left off for 15 minutes then hooked up but still no start and blinking theft light. I also tried spare key and still no start. What else can I do. I had it towed to place that just bulletproof my truck. Truck has been running great. I did not want to leave it on the side off road in the middle of country all night.
View 3 RepliesFord 6.0L Power Stroke Diesel :: 2006 F250 Died While Driving And Won't Start
While driving uphill yesterday, my truck 6.0 f250 completely died. Added oil cause it's been a while and tried starter fluid. Cranks but won't start. Pulled OBD codes p0300, p0304, p0401, p0460, p0562, p0606, and p2290. Checked IPR, works fine. Checked fuses. Low voltage codes are most likely from battery dying during the test.
View 2 RepliesFord 6.0L Power Stroke Diesel :: 2004 F350 Just Died Now Won't Start
M buddy's truck just died and won't start. So far we have changed the ficm because the voltage would fluctuate down to 25, the ficm harness as it was chaffed through and bare wires touching each other, both fuel filter, tested the alternator, new batteries, new air filter and bubble test. The truck spins over and tries to go but won't. I have also tried starting it with the icp disconnected with no change. The secondary filter had lots of bubbles coming into it while filling it for the bubble test, but we did that a few times and no more bubbles. When trying to start you can sound fuel flowing through the secondary filter, is this normal? While trying to start there is black smoke coming out of the tail pipe. We have also tried leaving it plugged in over night and no go.
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2004 Truck Randomly Shuts Off While Driving
04 with 170k miles. truck runs fine. every now and then truck shuts off while driving. turn it off the it restarts every time. Only code that comes up is number 6 injector. The contribution test injector is firing right. FICM voltage is 47.5. has new ipr and hpop also 6k miles ago. Could it be number 6 shorts out or something crazy killing truck? or maybe a crank sensor.
View 14 RepliesFord 6.0L Power Stroke Diesel :: A/C Compressor Died On Truck
So the A/C compressor died on my truck. I am looking at replacing it myself and it looks rather tight in there. My labor manual says I have to pull the fan/fan clutch, fan shroud and right inner fender to gain access.
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: Truck Died While Driving Almost Like Ran Out Of Fuel
I have a 2001 F350 7.3l diesel.
My truck died the other day while driving almost like he ran out of fuel. Well he had fuel so I checked the oil and it was dry. There was an ugly puddle between the intakes and a whole lot on the ground leaking out. Also the puddle looked blueish.
Put in more oil and got him home but I can't find the leak. The only thing I've noticed is that the intercooler on the cold side came off slightly. A year ago I had to go mess with the UCVH and when I put it back together I had lost a dang intercooler duct clamp and replaced it with a sturdy ring clamp. Well it wasn't sturdy enough.
How much would this leak if it came off for a little while and how serious of a problem would I have as a result? I don't have any check engine light and as long as he has oil he runs fine.
Since I have reconnected the intercooler and idle tested the truck I can't reproduce the leak. I don't believe that a huge amount of oil is running through that intercooler because the turbo is lubricated through another system I have read. So what gives?
Also I am getting weird dip stick reading. For a little while when I ran the truck today he was showing WAY over full on the dip and then down again a little bit below the operating range line. Also there are a lot of air bubbles on the dip stick when it comes up. Way more than I am used to seeing.
Also, I really like the idea of cleaning my engine off really good. It's a frigging mess now. What precautions can I take to clean it up good without making a huge mess. Can I just go the car wash that has a degreaser hose and drain and just spray it down like nothing or is it sensitive and finnicky when wet? Cleaning between the intakes seems almost impossible without getting the whole turbo system out of the way. Should I be thinking about that?
Ford 6.7L Power Stroke Diesel :: Reduced Engine Power Message Came Up On Dash And Truck Died
2015 F350 6.7L, 43,000miles
My family and I were driving into West Virginia this morning when the reduced engine power message came up on the dash and the truck died. I coasted off to the side of the road as best I could and got out. Immediately I smell diesel fuel. I look under the truck and there is fuel all over the passengers side frame and when I keyed it back up fuel started spraying down by the right front wheel.
Pulled the fender liner back and saw a small rubber hose that looks like it came off of a tee fitting down by the egr components. I tried to get it back on but wasn't able to get it seated 100% and when I tried to restart it blew off again. Truck is completely stock and ran perfect right up until it died.
Ford 6.0L Power Stroke Diesel :: When Come To A Stop Sign And Slowing Down Truck Died
So about 3 days ago I made a long 9 hour drive. No problems at all but I did allow my fuel to get a little lower then I normally do. About eighth a tank had 30 miles left on the digital read out. Stopped and filled up at loves where I always get my fuel. And off I went drove it down to 3/4 a tank and made it to my stopping point. Got in to go about 7 miles down the road and come to a stop sign and slowing down the truck died. I thought crap I forgot to turn off the auto start but never done that before. Stopped and stared truck as normal. Made it to my stopping point again. Headed back to the house and doing on average 55mph and truck surges like it wants to die but doesn't.
Rpms drop below 500 and it keeps going I get to same stop sign and slowing down again doing maybe 25ish and truck dies again as I have my foot on the break. Put in nut and started it right up and drive on home. Today went about same distance. Only this time I started it with key and was doing down other things while letting it run it just dies start it back up and take off get to where I was going and it surged or hiccuped so to say. Again started it once I was getting ready to leave and let it run for about 5 min and it died had the heater on as it was chilly out by the lake. Got in and restarted it and it was blowing cold air and had a diesel smell to it. Wife asked me if truck was going to blow up. Backed out of area and put in drive and made it 80' or so and truck died again doing about 10mph
Checked so far
Batteries checked and both are good
No mods done to it
New ICP sensor and pigtail
New water pump
New injectors 20k miles ago
Oil changed 1100 miles ago
New filters upper sad lower
2003 Ford F-250 King Ranch 6.0
Ford 6.0L Power Stroke Diesel :: 2004 F350 Truck Will Not Start
A little background, this is an 04, f-350. It sis not start a week ago so I charged the batteries and it started, started fine this morning, (had not driven it for the week) Drove it to work, 35 miles, parked it, and it will not start.
I downloaded Torque and got a few numbers,
HPOP 1900 FMP 48V (repaired last summer) and FVP 11.5V.
Ran out of battery to surf more and look, so I am trying to figure out the app, and the issue with the truck. It seems to turn over good, until I ran the battery down, and the GP cycles normally, and the injector buzz seems good. Temp is in the 50's...
Ford 6.0L Power Stroke Diesel :: Truck Just Died - Engine Control Fuse Blows
Had just got done filling up with diesel, drove 1/4 mile and truck just died. Tried to start it and nothing. No power to edge tuner either. Fuse #22 20a under steering column blown (engine control). Replaced and keeps blowing. not sure what is causing it. Just another wrench to throw in my wedding week!
View 13 RepliesFord 6.0L Power Stroke Diesel :: Truck Died Side Of The Road After Knocking And Blowing Tons Of Smoke
On way way to Florida and got 5 hours away and after the truck ran flawlessly for 5 hours it all of a sudden started billowing smoke, lots of knocking, and died. Now the engine won't turn over, tries to but acts like it's stuck. No codes...Accidentally crushed the cord on my CTS so no way to read codes. Just did studs and injectors
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2005 - Died While Driving - Won't Restart
My Brothers truck died while driving and won't restart. I am going to be getting IDS on it tomorrow night and just wanted some feedback on things to watch. I am planning to watch FICM sync, ICP pressure, IPR %, FICM voltage, and fuel pressure(not in IDS). Anything else I should watch while testing?
Edit: this truck is a 2005
Ford 6.7L Power Stroke Diesel :: Turbo Died When Driving Down The Highway At 55 MPH
Turbo is dead. I knew this day was coming. It died driving down the highway tonight at 55 MPH. Plenty of power since I left the office, all of a sudden the tone of the engine changed to a 6.0L and there was no power at my disposal.
Nursed it home keeping an eye on EGT's and let it soak while I ate supper.
Started it up, let it idle for a minute and tried a few revs but no boost and no turbo whistle.
Garage actually had a very slight haze to it after the test revs so something is broken.
DPF shouldn't be allowing any type of smoke to pass.
Bummer. Now I need a rental so I can get to the airport. Murphy's law has been in effect all day between software upgrades (IT stuff) and now my truck.
No CEL (this is shocking to me) but I found : P132B - Turbocharger/Supercharger Boost Control A Performance