Elantra XD (2001-06) :: Rear Brakes Making Noise While Coming To Last 10 Mph To Stop
Any fix for the rear brake noise I am getting on a 2001 Elantra. I pulled the drums off and inspected the drums and shoes all looks fine. Then I adjusted the brakes cleaned everything and still get noise. It occurs as the vehicle is coming to a stop last 10mph to stop.
View 13 RepliesLexus GS 2013+ :: 2015 - Passenger Side Front Left Wheel Making Grinding Noise
My 2015 Gs 350 F sport started making grinding noise from the front passanger side wheel. The noise comes from driving and not braking so im assuming its not the brake pads and its not squeaking noises as a worn out brake will sound.
View 14 RepliesElantra XD (2001-06) :: Loud Grinding Noise Coming From Front Of Car When Decelerating At Low Speeds
Having problem with my car (2001 Elantra GT) - over the last month or so it's been occasionally making a very loud (not but consistent) grinding noise coming from the front of the car when decelerating at low speeds. The noise sounds like gears slipping over each other but cuts in and out. It's pretty loud and not a nice noise to hear! Sometimes it makes the noise when I brake firmy but not until I reach lower speeds... mostly it's just when coming to a stop, but it did it once last week when I was pulling very slowly out of a parking spot and not even braking.
As it's become more frequent (going form maybe once a week to several times every car journey) I have started to feel something in the brake pedal also, like there's something kicking it from behind. I took it to a mechanic and had to pay a ton of money to get a broken front left ABS ring replaced (it also had the front right ring replaced in May), and within 2 minutes of driving away from the place the noise was back. Before I spend even more money that I don't have on taking it back for extra diagnosis.
I'm told that this is almost certainly the ABS system that has a fault even though the ABS light never shows except when I start the car, and I've taken the fuses out of the ABS in order to confirm that it is. I haven't heard the noise after a few days of driving with ABS unplugged so I think we can be reasonably sure here. Is there anything that I can check myself or test (I'm not very handy when it comes to cars) or can you tell from this information what it's likely to be? Other things that I've noticed with the car which may or may not be relevant are:
- the warning lights for brakes, ABS and TCS are all lit with the fuses for ABS1 and ABS2 taken out. I take it this is normal for all 3 to illuminate with the fuses out?
- since unplugging the ABS I've noticed a slight metallic squeal from the brakes as if the brakes are worn down. Didn't notice this before I unplugged ABS though it may have been there, not sure.
- sometimes when going over a speed bump or just a minor imperfection in the road I hear a clunk in the front of the car and feel something move in the underside of the car. Happens mostly at lower speeds also, but not if I go over the bump really slowly.
- in the fuse box when I took out the ABS fuses I noticed there was a bit of minor melting/brown burn marks on the top of the connections marked (iirc) ECO3 and ECO4 on the diagram (large white connectors). Is this anything to be concerned about?
- sometimes when I have air coming into the car through the air vents it will become significantly warmer for a few minutes, then slowly go back to normal. Can't think of any circumstance that links the times when this happens (eg. speed, weather etc).
- the oil pan has a leak which is on the list of things to fix when the car works properly.
Ford F-150 (2004-2008) :: 2006 - Grinding Or Whirring Noise Coming From Front Passenger Side Wheel
I owned a 99 f250 a little while ago. Just bought a 2006 crewcab F150 xlt about 2 months ago, and for the past month there has been this unusual grinding or whirring like noise coming from the front passenger side wheel.
I took it to the mechanic and he found a bad wheel bearing on drivers side and replaced it but that wasn't the issue. He could hear the noise but wasn't able to figure out what the actual issue was.
The noise only happens when my foot is on the throttle. (not when coasting) and i also just discovered that it doesn't make any noise at all when put in 4x4.
Subaru - Forester :: 2006 - Brakes Inconsistently Making Dragging / Grinding Noise When Coming To A Stop At Low Speeds
I have a 2006 Subaru Forester with 115K miles. It's been well-maintained and well-loved.
For the past few months, the brakes have been inconsistently making a dragging/grinding noise when coming to a stop at low speeds (<5mph). It sounds to be coming from the front half of the car - I can feel it vibrating a little near the driver side. We've taken the car in to be looked at three times - each time, the mechanics think they've heard the noise and report there is absolutely nothing wrong with the brake pads or rotors. Twice they reported a shim was out of alignment. After the last shim adjustment, the noise got a little better - instead of grinding, it's more of a dragging sound now. Because the noise is inconsistent, I haven't been able to crack the formula of the conditions that produce it, other than that it only happens as I'm coming to a stop at very low speeds.
Is there something besides the brakes we should be having inspected? Does this sound safe to drive?
Ford F-150 - 1997-2003 :: Passenger Side Brake Started Making A Grinding Noise
I have a 1997 F150 (truck in signature). In December my passenger side parking brake cable broke so I replaced both rear cables (front cable appears in good condition).
This past Friday the passenger side brake started making a grinding noise so I pulled the drum to find the self adjuster cable broken and the ratchet jammed between the shoe and the drum. I pulled everything apart and put new shoes (the pin the ratchet pivots on was broken off the rear shoe)and all new adjusting hardware (adjuster screw, ratchet, cable, and cable guide). The rest of the hardware looks in good condition (still paint on the springs and retainers). I got everything put together and took it for a test drive, it had a nice firm brake pedal (it's been a while since this truck has had a firm pedal) and great stopping power.
Took it to work today, and on the way back I stopped to pickup a package from the UPS store. I set the parking brake and put the truck in 1st like I always do. When I got back out to the truck to drive home, I released the parking brake but there was still obvious drag as I drove home (no good place to stop during rush hour), got out of the truck and it reeks of burning brakes. I pulled the driver side drum off (after it cooled), which was rather difficult, and everything looks to be in order except the rear shoe was not touching the post at the top of the backing plate. I checked and the adjuster was still all the way in, so that isn't the issue.
I pulled the parking brake cable out to slack the drum side of it (with the pedal released there is some spring tension from the pedal mechanism) and clamped it with vice grips so the cable was slacked and the shoes were then touching the post, and the drum could be installed and turned relatively easily, I then removed the vice grips and let the spring pull the tension out of the cable and the brake held firmly (requiring considerable effort to turn the drum). Is there anyway to adjust the spring tension on the parking brake cable when the parking brake is released?
Additional notes: when setting the parking brake, the pedal will only go down an inch or 2 before the brakes are locked up tight and the pedal won't move, it used to go down several inches before. also I noticed that the feral on the end of the drivers side cable (that locks into the lever attached to the rear shoe) is deformed, like the cable has too much tension on it. The cables are the correct ones for my wheel base according to Autozone but I'm starting to wonder if they are too short. Spring tension on the parking brake cable (when the brake is not set) causes the parking brake to drag. How do I get the parking brake to stop dragging? ("star" adjusters are new and adjusted all the way in).
IS F (2008-2014) :: Grinding Noise Coming From Front Brakes When Slowly Coming To A Stop Below 5 Mph
Just got a 2013 IS-F. Loving this car, but discovered an annoying issue. Grinding noise coming from front brakes when slowly coming to a stop below 5 mph. Is this normal?
View 9 RepliesPrius (Gen 3) :: 2010 - Grinding And Rattling Sound Coming From Right Passenger Side
Mine is 2010 gen 3 Prius. I bought it brand new and about 6,500 miles. From the beginning, I sometimes hear a grinding and rattling sound coming from the right passenger side. It is not from plastics. It is mechanical sound. But the problem is it does not happen all the time. So we were hesitant to go to dealer because they will never find it. But it got more frequent with cold weather.
Now, it does make rasping buzzing sound like a loose fan usually after I start a car in the morning and the heater is kicked in. I don't think it has something to do with fan because if I just run it itself in high speed, you cannot hear it. It is just some bad combination that makes this sound that makes you go crazy.
We are afraid that something big will happen after the warranty is over but as we expected the dealer said they do not hear the sound. The sound comes out in low accelerating and disappears in high accelerating. Now I really regret having bought Hybrid. It looks like the dealershop has no clue where to look at. I think the sound gets worse with the cold weather.
Elantra XD (2001-06) :: 2004 - Transmission Making Slight Grinding Noise When Putting Into Reverse Only
No codes, transmission makes a slight grinding noise when putting it into reverse only. Has a slight bump from 1st to 2nd. I flushed 16 quarts of the sp3 through it. Been researching and see a lot of talk about the output and input sensors. Not my car but my sisters. Needs axles, timing belt water pump, ps return hose, plus have champions in there and old ass hyundai wires.... thing does idle rough, motor mounts are new.
View 1 RepliesHyundai - Elantra :: Tch Sound In Front Passenger Side
My 2007 manual transmission Hyundai elantra makes a single "tch" sound in the front passenger side. It does it at high speeds in 5th gear over long distances. Also if the car sits for a while it will make the noise right after shifting to second gear if the rpms are a bit high. What it could be?
View 2 RepliesElantra XD (2001-06) :: Clicking Sound When Making Turns - Driver Side CV Boot Broken
Last year, when the passenger's side CV boot ripped and all that grease few around, it started to make that familiar clicking sound when making turns. I had a heck of a time replacing it. Did not like to doing the work.
Now, the driver's side boot is ripped. Grease everywhere. The clicking sound is just starting to be noticeable. Can I just wash out the CV joint and repack it with grease and a new boot? Or, should I just replace the CV joint?
Camry :: 2010 - Passenger Side Rear Brakes Making Metal On Metal Sound
At 75K my passenger side rear brakes were making metal on metal sound. I was really surprised as I have always learned that the front brakes take 80% of load and they always go out before the backs. So I took the wheel off and sure enough the pads were metal on metal. Changed everything out. (new rotors). I then went over to the driver side rear brake. Looks brand new. The pistons were barely out. I figured this caliper is bad. (I haven't change yet)
When I drive I can hear a very faint metal on metal sound when I brake. VERY FAINT. So with 75K miles on I figure the front brakes are due. Today I took the wheels off and inspected them. Tons of pad left on both of them. If I didn't know better I would say a brake job had been done very recently. (I've owned the car new so I know they have not had a brake job) However after reading many articles on this site I found a thread where one user said he was changing his front brakes for the first time with 110K on them and the pads still had 10K left in them. So the fact that my front pads are still pristine at 75K may not be a big deal (or not as big as I thought. Also I am not hard on brakes.)
However I'm not sure what is going on. Why would the passenger rear brake be metal on metal at 75K and the three other pads are like new. Is the passenger rear the only one working (or working much harder than the others) meaning the other three are bad? Or is the rear passenger bad and the other three are good? I have a working knowledge of cars but I am by no means a mechanic.
Yaris/Scion & Vitz :: 2000 Echo - Grinding Sound Coming From Passenger Side Of Vehicle Under The Hood
I have a 2000 Echo, Automatic, and I have a grinding sound that appears to be coming from the passenger side of the vehicle, under the hood. I had my A/C replaced, and new drive and power steering belts put in, 1,400 miles ago. I have noticed the sound is bad in park or neutral, seems to quiet down if I put it in Drive or Reverse while the engine is cool, and is particularly bad at highway speeds. I live 10 miles from my mechanic, on a highway, and am hesitant to drive it to them as it is all highway or rural roads (45 mph plus).
I drove it about 15 miles from when sound started (barely noticeable) to when I stopped and had it towed home. Belt deflection appears to be only about .3 in, manual I have calls for .43 to .51, but I may not be measuring it right....
Sonata I45 (YF - 2011+) :: Brakes Dragging Sound Coming From Passenger Side Mainly When Car Is Cold
I have a 2011 Sonata with 40k miles and am hearing what sounds like a dragging ... medal touching medal .... brakes dragging sound coming from the passenger side mainly when the car is cold. Could this be a possible wheel bearing going out???
the car is lowered about an 1.5 inches and and sit on a staggered wheel set. 18x8.5 up front and 18x9.5 in the rear. Just want to know if I should be worried.
Maintenance - Repairs :: Grinding Noise In Front Passenger Side?
I had my first car 3 months and every thing was going fine, this afternoon I was leaving the motorway and heard a grinding noise in the front passenger side. There are marks in the disc but the pad looks like it has enough meat on it. What is the problem? The driver's side is fine no noise. There is a bit of a lip on the disc so I think it would need changing soon but it's not that bad.
View 19 RepliesCorolla / Matrix 2009-13 :: Toyota Making A Loud Grinding Metallic Noise On Front Left Side
I have a 2009 Toyota Corolla and it's making a loud grinding metallic noise on the front left side. It does it while I drive the faster I go the louder it gets. When I turn to the left it makes it louder, when I turn right the noise decreases. PG&E have been breaking the roads by where I live and there's a lot of little rocks I drive thru. I'm wondering if that's the problem?? What do I do?
View 4 RepliesFord - Focus :: 2004 - Grinding Noise From Front Passenger Side
I've had a grinding noise coming from the front passenger side, sounds like the wheel area of the car, for many months. I've driven thousands of miles on it like this, mostly because I'm broke and the car otherwise runs fine, but also because when I've taken it to mechanics, they are stumped.
I took it to a shop about a year ago and he had it for a week, had different specialists look at it and ruled out anything mechanical (wheel bearing, etc.) In the end, he threw up his hands and didn't want to give me any more free labor for his non-diagnosis, and thought he ruled out everything but the transmission. I took it to a transmission shop recently, and the guy ruled out right away that it was the transmission. He tried to diagnose the problem and was stumped too.
Here's what it is doing. It makes a grinding noise around the front passenger wheel when I accelerate. Only when I accelerate. It seems to be more active when it is cold, and after I've been driving the car for about an hour or so, it goes away. It used to only really happen when taking right-hand turns, and that is still when it is at its worst, but now it does it anytime. However--some days it is very bad and some days very light. One day--of course the day I designated to take it to the shop--it stopped altogether and drove like new. Just until I got it home. It is worse in low gears, and used to only happen in first, second and third, but now on an active day I can hear it on the interstate in fifth gear.
The shops I've taken it to can't seem to figure out what it is. Reading threads online, I've learned that people with similar problems found the problem was a bad passenger side motor mount. I have the car at a new shop right now, and I asked them to replace the motor mount, even though it looks fine. I had a long talk with the mechanic there today and he seemed a bit skeptical, but thought it was a possible solution.
Should I spend the money on a motor mount even if it looks okay? (I've also read that the Focus mounts look fine from the exterior when they are bad because they have a gel interior that busts). Especially if this doesn't work, I'm going to be back at square... um, zero.
Ford F-150 (2004-2008) :: Grinding Noise From Front Passenger Side
2005 ford f150 Fx4 So last Friday I started hearing a grinding noise from the passenger side front of my truck. sounded like metal on metal. So I started rooting around and noticed that bottom ball joints were shot. so replaced bottom ball joints on both side. I aslo replaced wheel bearing hub assembly on both sides, still heard the grinding. So I noticed that both axles were slinging grease, so I replaced them on both sides.
Still heard the grinding noise. So then I removed everything from the passenger side and noticed that the locking hub actuator was grinding both axle and the wheel bearing hub. So I just got done replacing that on the passenger side, put it all back together, and still grinding noise ringtones free. Also replaced the 4wd solenoid that they said gets water in it, and I replaced the check valve. And I put new Rotors and breaks. What it could be?
Explorer :: 2000 - Grinding Sound Coming From Front Right Side / Steering Wheel Shaking
I just recently bought a 2000 Explorer, 4.0 OHV, 4x4 with about 150,000 miles.
I've had the vehicle for about a month, and ever since I bought it, it's had a grinding sound (sounded like wheel bearing) coming from the front right side. I replaced both right and left bearing/hub assemblies, and took it out for a drive. The initial sound that I thought was bearing noise is still there, and at about 65mph I started to get a little bit of steering wheel shake. I took my foot off the gas and it stopped. I accelerated up to about 70mph and it seemed ok.
I hit a VERY small bump in the road and the steering wheel started shaking like hell. So bad that I almost lost control. I slammed the brakes and the shake stopped instantly. I took it home and put it up in the air, half expecting to see something loose or broken, and everything looks perfect. I re-torqued everything that I had taken apart for the initial hub/bearing replacement, and took it out again. Same issues.
I never had ANY of these problems before I replaced the hub/bearing assemblies, so I'm completely confused. I was thinking CV joints, but I have no clicking at all when turning, in forward or reverse, everything is smooth. Outer tie rods were done about 6 weeks ago..