Honda - Accord :: 2013 - Manual Transmission / Clutch Completely Gone
I have 2013 Honda Accord 6 sp manual with 25k miles on, its clutch was completed gone last week, got new replacement, local Honda customer rep. told me I should watch my driving pattern, should using more break, instead transmission slow down, particular from high speed/high gears. I told them, we have 2008 Civic 5 speed Manual, I taught my two daughters how to drive it, and the car is still running without any problem… And, this is manual transmission car, tell a driver can not using/changing gears slowing down car is a joke… but maybe I am wrong...
Is there a possibility Accord has design problem with inferior clutch materials used on their new 6 speeds manual Accord? Since car has new clutch, should I keep it for a while? Or, sale it immediately? I just can’t not see I am going to come up another 3rd replacement on clutch before the car get into 60K miles.
Tiguan :: Noise Like Changing Gears In Manual Car Without Clutch Completely Depressed
I have a 2011 Tiguan 125TSI with the 7 speed DSG. When it starts cold, you can hear a noise that sounds like a bad gear change when going from 3th to 4th, and 4th to 5th. It almost sounds like changing gears in a manual car without clutch completely depressed. It has been there since I got the car brand new, but recently it seems to be getting worse.
Once the engine gets warm, the sound goes away and gear changes are smooth.
I've asked the VW dealer about the sound and they tell me it is normal. Is this right? The problem is it is very hard to demonstrate to VW the issue since it may happen only once when the engine is cold. I've left it with the dealer overnight and they were able to reproduce it in the morning... but again, they tell me this is normal.
Golf/GTI VI :: While A/C Is On Clutch Pedal Goes Soft
Just as the title states. When I put the AC on in the car my clutch pedal gets some play in it, enough that it messes up shifting and gets jerky. I tried searching, but no results
View 14 RepliesGTI 337/20th Anniversary :: Clutch Pedal Went Soft?
We were headed home the clutch pedal went soft... Ok, I thought it's either the clutch master or slave. I get it home and replace the master and after bleeding I had good pedal feel.
Great I thought, I got lucky and it was only the master. Drive it around for a bit and get on the highway and just as I was about to downshift the pedal went flat to the floor again.
Well after pumping the pedal until it had good feel again I got it home and bleed it a couple more times just to make sure I got all the air out. Drove it again. Same thing, after a little while the pedal gets soft again.
Now before I go and replace the slave is it possible I have a faulty master? Having issues after replacing the master?
Passat (B7) :: Clutch Pedal Is Soft And Sometimes Will Not Work
I have had everything related to the clutch changed, and I even had a dealership bleed the clutch line. The problem is the clutch pedal is soft and will sometimes work good and sometimes won't. If I prop the pedal to the floor for a few hours, it works fine for the day. what gives?
View 1 RepliesTacoma :: 1998 4wd Suspension Is Too Soft?
I just bought a 1998 Tacoma v6 SR5 TRD excab with 112k miles. I'm having trouble figuring out why the suspension on my truck is so soft and even dangerously unstable when driving at highway speeds. Is it my shocks?
When I hit a bump on the highway, 65-75mph, it rocks side to side really bad. But at lower speeds it takes bumps very good almost like a Cadillac. It has Monrore sensatrac shocks at all four corners, so I figure they are not stock. Do you think I have the wrong shocks on it? it doesn't sag at all so I doubt the springs are worn out at 112k.
GTI 337/20th Anniversary :: Clutch Pedal Is Soft At First And Then Gets Harder
I keep finding air every time i bleed my clutch. I am not losing fluid but i can not figure out whats causing my problems. The pedal is soft at first and then gets harder and it sometimes needs pumped before i change gears or to even get into gear. I am afraid its the slave but i also just may have air in the system.
View 8 RepliesSubaru - Impreza :: 2006 WRX - Soft Clutch Pedal After Replacement
Just the other day I got the clutch replaced on my 06 WRX. I took it to a reputable workshop that I've dealt with before. When I got it back the clutch pedal feels very soft and goes to the floor with ease, whereas before it was a lot harder and felt good. It works good and dosen't slip but just a soft pedal. I also went for the OEM replacement and not aftermarket. Some of the google searches I've read say the pedal will get harder after about 1000-2000 km.
View 5 RepliesGTI 337/20th Anniversary :: Clutch Soft In The Cold, Stiffens Up When Warmed Up
20th with 120,000 miles. Ok here's my problem, get in my car in the morning after a coldish night, (around freezing) clutch pedal goes almost to the floor with no resistance, i pump it a say 5 or 6 times and it gets stiffer but not 100% i drive it for 10 or 15 min and it warms up and the clutch gets back to normal stiffness. I'm thinking its the master or slave cylinder going bad or maybe it just needs to be bled and before i go and buy both of them and replace them, just wanted some opinions. Also its not leaking fluid at all and the reservoir is full.
View 2 RepliesEclipse - Pump - Clutches :: Hydraulic Clutch Soft Pedal
We have a 1997 Mitsubishi Eclipse with a hydraulic clutch. The pedal is very soft in the morning and requires a good bit of pumping the pedal to get good pressure. I know the system needs to be bled. Does this mean one of the cylinders is bad? I have added a little bit of fluid over the last year- maybe 2 or 3 ounces total. Right now the fluid level seems fine but it still needs to be pumped before driving.
View 7 RepliesGTI 337/20th Anniversary :: Clutch Pedal Goes From Being Soft To Very Hard When Close To Disengaging
I have an Imola 20th and recently i have been having some problems with my clutch. The pedal goes from being soft to very hard when its close to disengaging. It also engages very heavily when I go to let it out. This only started happening recently when temperatures started to drop if this has any effect on a clutch. Also, I replaced a shift fork two months ago and was curious if there was possibly anything going on with seals around the slave cylinder.
View 2 RepliesGolf IV / Jetta IV :: Clutch Pedal Feels Soft Since Replacement - No Air Coming Out
I changed my oem clutch in my mk4 golf 2.0l with a stage 1 ecs tuning clutch kit. Lightweight flywheel, clutch disk, pressure plate and throw out bearing. But since I have my clutch pedal has been less stiff then usual. I like my clutch pedal as stiff as possible but it just isn't I bled off the slave cylinder. When I was done no air was coming out but it is still way to soft for me. What should I do next??
View 6 RepliesFord Ranger / B-Series :: Soft Clutch / Gears Grind When Shifted Especially 1st And 2nd
I have a 96 2.3L 5 speed Ranger. The clutch has been getting softer and softer until about two weeks ago when I couldn't drive it anymore because gears would grind like crazy when I shifted, especially 1st and 2nd. I had no time and just drove my other truck but now I've had a bit of time to look into it. I went to bleed the clutch and then realized there was no fluid in there. So I tried to put fluid in but nothing happened. The clutch is still extremely soft. The truck won't even start when I have it in gear, it turns over and kind of lurches forward, even with the clutch pushed all the way in. It starts right up in neutral. So my guess is I have to do what I really don't want to... replace the clutch!!
Is it possible that since I just put more fluid in the clutch it may take awhile for that fluid to get into the cylinder and I have to bleed it again?
Celica :: 1988 GT Manual Transmission Grinding When Going In 3rd Gear
My 88 celica's manual transmission grinds a little, at times, when going in 3rd gear. I have atf fluid in it now as specified in the manual. Should I replace it with gear oil?
I don't want to damage the transmission or clutch.
Celica :: 1986 Mk2 Supra Manual Stick Too Loose?
My 1986 Toyota celica supra stick shifter is pretty loose and I don't like it. Any way I can tighten it up?
View 5 RepliesFord F-150 - 1997-2003 :: 1998 - Shocks For Soft Ride
I have a 98 F150 4x4 Super Cab Long Bed that still has the original shocks which are in need of replacing. What shocks I should get that would provide a soft ride?
View 14 RepliesCelica :: 1993 - 5 Speed Manual Left Drive Shaft Failed
My 1993 Celica, 1.6, 5-speed manual left drive shaft failed and I am trying to replace it myself. I have the new part in hand, but for some reason, the inner splined shaft does not want to go all the way into the transaxle. I have tapped the rotor end of the shaft with a mallet and tried to force it in, but everything Ive tried wont work.
My car is down for the count until I can get this drive shaft back in.
Celica :: 1987 Toyota 1600 GT - When Engine Completely Warm Up Idle Is About 1000 RPM
I got a 87 Toyota Celica 1600 GT, with a TVIS 4A-GE engine in.
My problem: when i just start the engine cold, it revs to 2500 RPM, and stays there for 1-2 minuttes and then falling to about 1500 RPM, and when the engine is completely warm my idle is about 1000 RPM.
first i think that 2500 RPM cold is a bit to much, and i dont know what to do with it. but my biggest problem is when the engine is fully warmed up, and i rev it to lets say 3000 RPM and then lets the gas of, the engine falls to about 500 RPM sometimes it stalls but if it not stalls then it would slowly gain some RPM and then it goes up to 1000 RPM again.
How can i prevent the engine falling that much when i let the gas off? it's quite annoying when i drive the car and comes to a stop it sometimes stall.
Elantra XD (2001-06) :: Clutch Won't Completely Disengage
We swapped transmissions in 01 elantras.. We installed a new clutch kit . When we go to start the clutch won't completely disengage, it only pulls it some, not enough. We replaced Tran fluid and bled it. We swapped out the throw out bearing arm and at first it worked now it doesn't..
View 3 Replies