Toyota - Celica :: 1990 - Has Grinding Noise While Shifting Into 2nd Gear
got a sweet deal on it but only 1 problem with the car. when i shift into 2nd gear there is a grinding noise, however it doesnt grind if i drive super slow... it doesnt really matter if i upshift or downshift into 2nd it will make the noise either way... also the grinding noise is only there WHILE shifting the lever into 2nd gear so its only there for a second, once the lever is shifted into 2nd gear there is no grinding noise at all...not sure if this is related but the clutch pedal also feels very lose just when its about to hits the floor...
View 4 RepliesFord F-150 (2004-2008) :: Shudder When Taking Off From A Stop Or A Very Slow Speed?
Looking at a truck at a dealership. 04 F150 Lariat 5.4 3v? 2wd SuperCrew 148k miles. Bone stock besides the bedliner.
Truck is pretty nice besides these 4 things. Kind of a shudder when taking off from a stop or a very slow speed. Adjustable pedals don't work.
New brakes, but possibly the rears are dragging a bit. Was able to turn them in neutral and the rear on jacks. Extra, guessing because of the newer looking battery, some systems lack data from the OBD2
I'm mainly concerned about the shudder from a complete stop/1-2mph. At the dealer, to leave the lot, the driveway was elevated. I think it showed very well climbing that hill. As it was noticed and played with the gas a bit. Otherwise, you stomp the gas, it may shudder for a second or two, (3-5 times?) once it hits about 3000 rpm in 1st, its fine. Only ever seemed to do it in 1st and never any other gear, never on any gear changes.
We lifted the rear end up on a jack and fiddled around. Put it in neutral and spun the wheels, tried to mess with the drive shaft... According to dad, who was looking at it with me said it was fine and that it's normal to have a little bit of slop, but I didn't notice any real slop myself, tried to push on the driveshaft on the transmission side and I think it may have moved a bit but it didn't feel loose or clang or anything. Although I didn't get to push on it too hard because he was rotating the driveshaft at the time.
I assume new fluids in engine and trans. My dad said something about old oil marks on the transmission pan area or something. Both to the fill line.
One thing that I wonder about is how long this truck has been sitting. I wonder about the differential clutches. I'm not that sure what it really has for the rear end. But google had mention of clutch packs in the rear. I wonder if because it's been sitting that the oil has settled out of the clutches or something. There was a mess of silicon on the rear diff cap area. Couldn't tell if it was new or not. I think we put 10-20 miles on it at least and only looked under it for maybe a half hour... Still did the clunk/shudder at a start from a stop, when we returned it.
So, what could be causing this clunk/chatter when talking off from a stop/1-2mph roll?
Axle wrap?
Differential Clutches?
Differential?
Driveshaft?
Transmission?
Celica :: 1987 GT Taking 10 Seconds Of Cranking To Start
I have an '87 Celica and it takes a good 10 seconds of cranking to start. After being parked only 24 hours, it's the same thing. It won't even give a hint of a kick until about the 8 second mark. Then it'll give a couple of sputters and eventually fire right up. Is this the fuel pressure regulator that's the problem? Is it not keeping the fuel at the rail pressurized properly when sitting? It's just annoying having to sit there cranking for so long to get going. I would think if it was the pump, it would give me problems when running.
View 5 RepliesFord Transmission :: 1990 E250 - Shudder When Starting Off From A Stop
I am not the original owner of this 1990 E250 cargo van with a 302 in it. I am trying to troubleshoot this shudder I am having. It only happens when I am just starting off from a stop. Every other place the tranny runs and shifts great. I trying to find a starting point and after reading a bunch in a bunch of different places, I am confused as to the tranny I have or even had.
It has in big bold letters METRIC on the bottom of the pan. It also has Automatic Overdrive and Ford on the bottom of the pan also. It is a 14 bolt pan with the two rear corners of the pan chamfered off. I see now it is DEFINITELY the AOD installed and NOT the AODE. The thing is my steering column is labeled 1 D and OD. That is a 3 spd overdrive to me. What the heck is going on? How can I tell what the tranny was that came out of the van?
When I look under the van at the shift linkage, you can definitely tell the linkage is colored red which to me looks like somebody has been down there playing around. Is it possible to put a AOD into this van with the steering column the way it is? Could this be a reason for my early shudder at starting off from a stop? Once I put my foot in it or get moving at a quicker pace, the shudder goes away. Something is not right with the way this tranny is set up. I am not even sure where to start.
Celica :: 1990 GTS Not Getting Any Spark
I have a 90 gts celica, which the motor went in it, so i put a 93 5sfe into it. I took the old distributor out of the 90 5sfe and put it into the new motor. I wasn't getting any spark. So i replaced the distributor with a known good one. No spark. replaced the coil and igniter, no spark still.
View 10 RepliesCelica :: 1990 GT 2.2L - Low Oil Pressure At Idle?
Just acquired a 1990 celica gt at a steal lol and needing some troubleshooting answers. tonight was the first night we really had drove it, but my husband drove it to work which is an hour away and he noticed that when he comes to a stop the oil pressure light comes on. as soon as he starts to go again it goes off. the engine does not make any noises other than the typical 2200 lifter chatter and it does not leak oil.
We plan on doing an oil change so we are not sure if that could just be the issue or if it's something else. we had this issue with a dodge ram we had and it ended up being the oil pressure sending unit. he took the one off the car and it did need some tightening up but however when he put it back on the issue was still there.
We do not believe it's any low compression as the car cranks fine and normal with no rising of the cranking as you would get for a cylinder with low compression. we aren't really sure about the bearings because well that's not one of those things easily tested but the engine doesn't make a noise which I know at times you won't have one.
Celica :: 1990 - Vibrates On Startup
90 GTS - Manual Transmission. 5SFE
I have a vibration that rattles the cab of the car during start up. But if you get out, lift the hood and listen, you cant hear anything. Its only in the cab where you can even tell there's something not right. The motor runs great and seems very smooth to the touch and visually.
The vibration does seem to go down as the car warms up..... Somewhat....You can hear the vibration when driving and go down through slight dips in the road. Kinda like hitting the rumble strips on the side of the hwy.When I release the clutch and under power the vibrations go away. Under deceleration the vibrations are loud.After weeks of research, both TN and the web, I have done all this so far.
Changed Plugs, wires, cap. All four engine mounts were taken out, inspected, and 3 of the 4 were replaced from a donor car. All 4 looked good anyways....
Swapped harmonic balancer/pully from a donor car.
Compression check. 196 200 200 208
Cleaned IAC valve.
Pulled off exhaust manifold and verified CAT isnt broken.
Inspected exhaust from front to back and cant find anything.
Replace timing belt, tensioner bearing and idler bearing while I was in there.
Took both fan belts off and ran car to see if maybe power steering or AC, but car still rattled even though they weren't turning.
Did head gasket while building this car up because it was leaking oil from the front return tube area.
Celica :: 1990 GTS - Fans Failed To Kick On
I recently took the engine apart and got the head resurfaced after the head got warped. New thermostat, waterpump, timing belt, serpentine belt, power steering belt, and gaskets for all sorts of stuff. After reassembling the engine everything worked fine. No strange noises. Only problem i am having now is that the cooling fan switches on really late, when the needle is 3/4 of the way towards H, sometimes even a little later. Fan is working as when i disconnect the cooling fan switch(bottom of radiator) and the fan does kick on. ECT was also replaced and nothing seems to work. I did replace the switch and the fans failed to kick on, unfortunately i got it from Autozone.This is a 1990 Celica GTS with the 5SFE 2.2L
View 8 RepliesCelica :: 1990 GTS - Water Pump Is Dying
I have a 1990 GTS with a transplanted 1996 S5HE 2.2 motor. This summer I started getting overheating issues and I believe my water pump is dying.
Here's the symptoms; car will run nice and cool on the freeway doing 70 with the tach turning at 3.5k. As soon as I get off the freeway and RPMs drop the coolant temp will spike almost into the red. Accelerating from the stop will drop the temp but it will hover near the high end of the middle till I get back on the freeway or RPM's go back up.
It does the same thing when climbing hills or when the engine is under load. It did it bad this summer when it was hot out and I was running the AC. Bad enough that it boiled over a couple times. The radiator is brand new and just based on the symptoms I'm thinking water pump.
Celica :: 1990 - Key Won't Turn In Ignition Switch
When I put my key in the ignition, I cannot turn the key. I tried putting a small amount of WD40 in the ignition and turning the wheel back and forth while trying to start, but all that did was make my key greasy and my wheel lock up. I've tried getting a new key made from Lowes and Home Depot, but their keys are too wide and will not fit in the keyholes. The only thing I am down to is replacing the ignition switch completely but I'd rather do that as a last resort because my car has had a big problem every week (alternator gone, new wheels, new master cylinder, new rotors/brakes). I haven't explored yet? And also, if it comes down to replacing the ignition switch, how would I do that without being able to turn the key?
View 2 RepliesToyota - Celica :: 1990 Turns Over But Will Not Start
I just got a 1990 toyota celica and it turns over but dont start. its getting fuel up to the motor. i got it from a friend that gave up on it and he got it from a guy that replaced the 2200 with a 2000 engine. everything looks to be connected but i dont know where to start.
View 1 RepliesCelica :: 1990 - Block Surface Crack
A little background on how I got into this situation. Bought a '90 Celica GT for $300, was told it had a blown head gasket. It started and sounded nice, if a little ruff. Upon driving, it would stutter (like a misfire) till 3k rpm's, then that would go away and she purred like a kitten. Ok I thought I can make this girl into a woman. I start my teardown and what I found was: front 5 head bolts were not torqued down, and the only place on the old gasket that looked like blowby was on cylinder 3 towards the front on the engine. I think to myself it was loose headbolts, bang I send the head in to get cleaned, buy the gasket kit and go about cleaning the various other parts.
I was cleaning the blocks mating suface, and discovered a small surface crack. It goes from one water jacket port to the headbolt hole and to the other water jacket port.
The headbolt hole shown is the 4th(from timing belt) on the back of the block. The loose headbolts were on the front.
The crack does NOT go down the side of the bolt hole, or the water jacket ports. I am just really afraid this means a new block. The parts I can return if all else fails, but Im down the tube on the money spent on the car and head cleaning.
Celica :: 1990 - Leakage From Oil Pan Drain Bolt
1990 Celica GT ... I will be completely replacing the transmission, and the flywheel while adding a new stage 2 clutch kit. Also replacing the shocks all around.
Okay now to the problem, I don't know exactly where or what fluid or fluids it is yet. it seems to be leaking oil from the oil pan drain bolt also it seems to be leaking coolant too from somewhere behind the oil catch pan area. I did not change the water pump when the timing belt snapped but it looks like some water corrosion on the pump itself. are these common problems and what will solve these leaks?
Celica :: 1990 - No Fire / Spark Out Of Coil
My Celica is running great, I drove about 30 miles and the car started hesitating to run, I was in heavy traffic, I could hear rattling sounds which appeared as though they were coming from the heater. I stopped at a stop light and I could tell something was burning out. I have lots of power, car is very fast. I went to the next stop light and the car died, it started and I went to the next stop light with plenty of speed and the car died and would not start again. I tried starting the car for 3 hours, no fire from the coil.
I have no spark out of the coil. I am confident the coil is good. I have 2 coils. I went to the salvage lot and purchased an "igniter" (ignition module). I installed it on my Celica, still no fire out of the coil. I have a relay under the glove box that clicks when I crank over the engine. The engine cranks over very well for over 3 hours. I have an after market alarm. Why do I not have spark out of my coil?
Toyota - Celica :: 1990 - Won't Start After Driving?
I have a 1990 Toyota Celica, and I've been having trouble with it not starting after driving. There are no symptoms when the car is running, aside from a very slight rough idle. The car starts fine after sitting for 3-4 hours, but for short trips where it's off for under 1-2 hours, it cranks but will not start. The cranking also seems weak unless I floor the gas while trying to start, and sometimes it will eventually start if I hold the gas while cranking. It always starts at the beginning of the day.
This leads me to believe I'm dealing with a flooded engine, but I'm not sure how to diagnose why. I thought it might be leaky fuel injectors, but wouldn't that cause symptoms when running?
Accent LC (2000-05) :: Car Shift Violently Between 2nd And 3rd Gear
I have a 2001 Hyundai Accent GS Hatchback, the car has about 41,6xx miles on it. When i drive it between 2nd and 3rd gear it shift violently, its almost like it shifts due to pressure, it also happens when it downshift too. Also the reverse went out, i can hear the pump running and it goes into reverse but when i press on the gas it acts like it in neutral. This is a daily driver for me.
View 9 RepliesCelica :: 1990 Vehicle Will Not Start Back If Warm
I have a 90 celica. I start it up and it idles fast until it warms up. then it runs great until i turn it off. then it will not restart! i went to the gas pump. it would not start after i pumped gas. it turns over but wont start. the next day it starts up fine. it does this all of the time. when it wont start there is no spark coming from the coil except when you let up on the keyl it sparks once.
View 5 RepliesCelica :: 1990 2.2L - Car Occasionally Stalls After It Is Warm And Won't Restart
1990 Celica 2.2 liter, 5SFE manual trans car with 239k miles.The car occasionally stalls after it is warm and won't restart. When is is cold she fires right up as it does most of the time when she is warm. To restart he sprays starter fluid in the intake or waits until it cools down. Also as the car gets warm the idle decreases to around 650. Adjusted idle speed to 750 but no effect. The only code is 1-2, low or no RPM, measured the RPM sensor air gap and within spec, measured the sensor resistance and within spec. sensor wiring and connector looked good, measured the temp sensor and within spec, disconnected the EGR vacuum line and no effect. Problem occurs once or twice a week but at the most embarrassing place.
View 4 RepliesCelica :: 1990 5SFE Sudden No Start / Just Crank
Installed a "new" battery in my celica (it was used but tested good) went to start up the car to see if it was good and the car started right up
Shut the car off cleaned up my throttle body a bit the went to start the car again it it would just crank and crank
I just put in a new fuel pump, so that cant be it, I have not checked for spark yet ( car is stuck at work )
I heard that the ignition coil likes to fail on these would that be causing this problem?