Golf IV R32 :: Part Numbers For 2 Interior Trim Pieces?
Looking for info about some part numbers? I'm looking for the silver aluminum trim on the driver inside door. Where you rest your left arm. Also the driver black air vent assy all the way on the left where the headlight switch goes.
View 7 RepliesFord Excursion :: Part Numbers For U Joints In Rear Drive Shaft?
I need to identify the part numbers for the u joints in the rear drive shaft. The guys at the auto parts store kept telling me I only need two until I showed them that there are clearly three. I just want make sure that I get the correct parts before purchase.
View 5 RepliesFord Excursion :: Rear Shock Bolts And Nuts - Part Numbers?
I've noticed quite a few threads looking for the shock bolts lately. I've replaced one of mine and just had another break. Today I ordered replacements for all 4 nuts and bolts.
The Bolt part number is - N605906-S2
The Nut Part Number is - N803714-S426
Ford Excursion :: Door Seal And Fog Light Bracket Part Numbers?
I need a new upper driver side door seal and the plastic driver side fog light bracket but can find part numbers for my 2005 Ex.
View 3 RepliesFord 6.0L Power Stroke Diesel :: Idler Pulley Bearing Part Numbers
I need to replace the bearing on my Idler pulleys, both smooth and grooved. I also want to replace the bearing on the tensioner pulley. What are the part numbers and the best place to order them from?
View 10 RepliesGolf VI R :: Installing VWR Springs - Rear Suspension Unknown Part
I am installing VWR Springs to replace worn stock components on my mk6 R. It appears that the previous owner slammed the car, and removed the "nipple" that holds the rear spring in place from the top. Both upper and lower spring isolators were present.
I am trying to find a name or part number for this unknown "nipple". I tried some combinations, such as "rear spring cap" and "rear spring centering guide". It looks like it would screw into the body, right above the springs themselves.
Ford Aerostar :: How To Replace Rear Coil Springs
Have been the owner of a 96 4.0 AWD for 10 yrs and if they still made this van I would get one in a heartbeat. Been doing a search on how to replace the rear coil springs with no luck... is there special tools or procedures involved?
View 8 RepliesLincoln - Towncar :: 1998 - Replacing Front Coil Springs?
I am going to replace front coil spings on my 98 town car. Do I really need OTC 7045B tool to remove springs?
View 1 RepliesFord - Explorer :: 2002 - Changing Rear Coil Springs?
I have a 02 Explorer that has 2 cracked rear coil springs.
How hard are they to change ?
What brand to use ?
I was looking at the Monroe Quick-Strut.
Ford Brakes/Suspension :: 1993 F150 - Coil Springs Leaning Forward
I am doing an sas on my 93 f150 short bed. my issue is that I've made coil spacers out of 1/2" thick by 3" tall by 4" in dia.... as you can see strength is not an issue here. i bought 6" lift coils for a 93' then decided to just say f it and throw a d44 straight axle under it. the springs on a 78' d44 are the same dia. top to bottom. 93' springs get smaller at the bottom so i made this spacer for two reasons.... 1 to have smaller seat for the bottom of the coil.. and 2 so i could make up the spring length difference between the two springs. The spacers are leaning forward due to the 7 degree c bushings on the radius arms.
View 1 RepliesFord 6.7L Power Stroke Diesel :: 2012 - Installation Of F550 Coil Springs?
I have a 2012 F350 CCLB with camper package (front coil springs @ 6,000 lbs). I was thinking of installing F550 coils springs, which are rated at 7,000 lbs, to provide greater lift up front.
Before performing this modification, what lift was achieved up front?
My endeavor is not to achieve level, per se, but rather allow for increased tire size, such as 35's and ground clearance.
Camry :: 2007 SE - Installed H&R Springs Now The Car Pulls To The Left
I had my dealer install a set of H&R springs the mild drop option. He put it on the rack and reset the alignment. I drove it and it pulls hard to the left. The car has never done this before. He then took everything back off recheck the suspension and found nothing wrong. He realigned the car and it still pulls hard left. The car is a 2007 Camry SE.
View 11 RepliesCamry :: Weak Struts After Installing Lowering Springs
Few weeks ago, I got the Tein spring installed on my camry. Drop 1.5/1.6 front/rear.
Problem is now I sometimes hear this clunking sound from the rear. It doesn't happen very frequently, just every once in a while when i drive through a small&sudden bump.
Only from the rear, nothing from front of the car.
Another thing is that when i reverse & turn (ex. getting out of garage), it makes one or two cracking noise from the front, small clunking sound from the rear.
I'm suspecting the strut may be bad. The mechanic guy said that my rear struts are bad (when he was installing the springs).
Am I in need to get new struts ?
Camry 2012+ :: Squeak In Front After Installing Lowering Springs?
I put HR lowering springs and I'm getting a bad squeak when the car goes over a speed bump . It's coming from the rubber on the end of the front springs ? Do they make a poly urethane upper mount?
View 4 RepliesCamry :: Rear Suspension Clunk Noise After Lowering Springs Installed
After having lowering springs installed, I've been noticing a clunk noise in the rear suspension when driving over dips in the road (eg. getting out of the parking lot onto the main road). It feels like having your wheels lifted in mid-air and being dropped onto the road.
View 14 RepliesCamry 2012+ :: Eibach Springs Installed - Rubbing Sound When Turn The Wheel From Only Driver Side
Installed eibach springs on the 7th gen camry? I installed mine this weekend, and I'm getting a like a rubbing sound when I turn the wheel from only the driver side. I removed the strut and spring combo to make sure everything was installed and aligned properly and it was. Just can't put my finger on why its only making that sound on the driver side.
View 9 RepliesCamry 2012+ :: Key To Start Car But Not Remote Part Of Key
I just bought a 2012 Camry SE. Came with one master key. Bought a replacement online and I am about to have it cut/programmed. I called an auto locksmith and the guy indicates he can program the key to start the car but not the remote part of the key. How do I program this part?
View 5 RepliesCamry :: 5th Gen 2004 LE And ES300 Part Compatibility?
I own a 2004 LE with the I4. How to convert our dull camry automatic shifter to the cooler es300 gated shifter? I know it takes some re wiring, and the shift linkage might be differant because of the I4 to v6 difference. I have a couple es300 at my local junk yard with gated shifters. I think in other markets outside the U.S. you could get the ES in a four cylinder with the gates shifter.
View 14 RepliesCamry :: Part Of The Shifter Panel Gets Hot Warm
I have a 2007 camry xle and I just noticed that part of the shifter panel, you know where it says P, R, D, etc, gets hot warm to the touch whenever I turn on my headlights instrument lights. Its the back left corner of the shifter panel where the wood trim and the brush aluminum cover meets. I don't drive to much at night so I didn't notice this before.
After about 20 minutes of having the lights on, it start feeling warm. There must be some kind of transistor there that powers the illuminated light of the P, R, D, etc.. Does your panel feel warm after your headlights instrument lights have been on.