Sierra :: Cylinder 3 Misfire Only Under Hard Acceleration / Code P0303
So my 2001 5.3L truck has 206,648 miles on it. Over the years, it's been serviced every 5K with the only big repair being head gaskets which were done about a year ago.
Two weeks ago, I hit the gas to merge into traffic and the SES light started flashing and I could tell there was a miss. I got off the gas and a few moments later, the light went out and the miss was gone. I pulled the code and it was P0303 so I change the plugs, wires, and the coil pack for Cyl 3 fuel filter and ran a double dose of Sea Foam through the gas tank.
Bad news is I still have the problem. The truck drives fine; in fact, I pulled my bass boat 75 mile round trip yesterday. Everything is OK till you hit the gas hard to merge or to go up a big hill or pass someone. When you hit the gas hard, SES starts flashing and there is a miss. I also noticed the valves ping loudly when the SES is flashing. The only code it's giving me is P0303.
Could this be a bad injector not delivering enough fuel at higher RPM/under load? I was going to swap injectors and see if the miss moves. Any tips on popping those injectors out?
Elantra XD (2001-06) :: 2003 GT - Cylinder 1 Misfire / Sputters In Acceleration
My car is misfiring, as in acceleration 90% sputters until I lay the pedal to the ground, which obviously isn't good for my gas. What do I do? I can't find anything online and I don't want to be throwing money into things that don't work.
View 4 RepliesFord Excursion :: 2000 V10 Shaking On Acceleration / Cylinder Misfire Or Dead
Well, I have been through the tech folder and all over the forum reading but cant seem to come up with a good first step. When i accelerate the truck shakes, by the sound it seems that its missing a cylinder. I guess it could also be the motor mounts. Besides replacing the plugs and coils, is there something else that could remedy a misfires or dead cylinder?
View 7 RepliesFord - Focus :: 2002 Cylinder 2 Misfire / Stumbles On Acceleration Between 2000 And 4000 RPMs
I've got a misfire problem with my Focus. It started about a month ago and did not trip a code until last week. It stumbles on acceleration between 2,000 and 4,000 rpms. It is only a slight stumble and although noticeable, it does not impede driveability much. Last week I was able to get it to finally trip an OBD code. P302 - Cylinder 2 misfire. I changed the plugs and wires with no effect. I thought I had it narrowed down to the coil or injector until my wife noticed a new wrinkle.
Under normal driving conditions the misfire is annoying, but my wife found that if she turns on the A/C, it is undriveable and will not accelerate past 30 mph without some patience and a neck brace for the bucking. My first thought was the A/C compressor was freezing up. I turned off the A/C and left the blower on and it would not stop missing. I turn off the blower and it smooths right out to the annoyance I described first.
Right now I drive the car without A/C and blower whenever I accelerate. If I'm going a steady speed, all is well and I can run the blower and A/C.
Ford - Explorer :: 2000 - Cylinder 3 Misfire Persistently / Engine Stumbles And Has Poor Acceleration
I have a 2000 Explorer 4.0 SOHC that I'm having a persistent problem of cylinder 3 misfire. I've changed plugs with Motorcraft plugs set to the proper gap, put on new wires and have checked the resistance across the ignition module, both primary and secondary without change. I doubt that the problem could be the ignition control module as only cylinder 3 is affected. I have Auto Enginuity that I use to read the codes, attempt a repair and then clear the codes only to have P0303 appear again. Obviously the engine stumbles and has poor acceleration.
View 14 RepliesGolf IV / Jetta IV :: Occasional Misfire In Hard Rains / No Acceleration
2002 AVH Jetta Wagon. When I got the car back in 2012 it had 121K and I changed the wires (ngk blue 57021) and plugs (ngk platinum) and she drove like a dream. A couple of months later I started having issues with wet weather and moisture causing misfires so I did the JB WELD fix and though I'd still get the occasional misfire in hard rains it lasted me pretty much until very recently, when I decided I needed to put in a new coil because the problem was getting worse (hardly starting up after a rain and bucking wildly till things dried out). Yesterday, I replaced the BERU with a new HUCO and the car started up fine and drove fine all day. I think there was a lot of moisture in the air last night and possibly some rain but this morning, SAME PROBLEM with a new coil. Misfiring like crazy, no acceleration.
I thought the NGK wires and plugs I got were rated to last beyond 20,000 miles. At this point should I assume the wires are to blame? Split somewhere or something? It's definitely related to water and the electrical system.
Ford F-150 (2009-2014) :: Shudder / P0301 Misfire On Hard Acceleration
Was driving to Airport yesterday and out of nowhere got the flashing check engine and shudder/limp mode while trying to merge/accelerate onto the onramp (had to gun it to go around someone who decided to stop on the onramp for no reason). Let off the gas and the blinking went away. Upon leaving the airport I was accelerating again at highway speed to pass and got the blinking light and then a solid CEL. Found my way to a Autozone and got the code read. P0301 Cylinder#1 Misfire. Was suggested to change COP and plug.
Changed COP on the spot and had to drive it home to my tools to install plug. Thought maybe that since the CEL was still on solid after changing that the code needed to be cleared for the PCM to function normally again. Still have shudder when accelerating hard, so thought it might have been injectors so got cleaning service done at Goodyear. Still have the issue. Disconnected battery and performed IDLE relearn just now and it still is shuddering upon hard acceleration. Stumbled across TSB 12-6-4 which speaks to my symptoms.......I do not have the plate which in turn would imply I do not have the PCM update it references.
I have not noticed a misfire nor had an acceleration issue before so this was a surprise to come out of nowhere. I'm going to be calling my dealership in the morning.
Camry :: 2003 V6 XLE - Misfire On Cylinder 5
I recently purchased a 03 Camry XLE V6 love the car, but the engine has been giving me trouble. Since owning the car in January it has been in the shop 3 times for a cylinder misfire on 5. They jave replaced the ignition coil, spark plug, and fuel injector and still would misfire, it might be a few weeks later, but it would still misfire. It is currently in the shop for the something, they have checked the fuel, electrical system, and compression tested the cylinder and all has comeback good.
View 2 RepliesCamry :: 2002 - P0302 Cylinder 2 Misfire Warning
I have a 2002 Camry, 2.4 with 155k miles.
This morning I was going to work and was making a lane change and hit the accelerator quite aggressively. Suddenly my engine started to run really rough and shook the car and the check engine light started flashing.
I checked the engine code and its giving me a P0302 Cylinder 2 Misfire warning.
I have read that there can be various reasons but I figured since this problem is consistent its not a vacuum issue? Could it just be a bad plug? I don't have the tools to fix it, I am going to get them soon to pull the plugs and inspect then, and will replace them anyway since I don't think they have ever been replaced.
Camry :: 2004 - Getting P0303 Code / Cylinder 3 Misfire
I have searched but with no solid answer..
What I got - 04 Camry, 231K, never had issues, do all my maintenance myself, brakes, plugs, oil etc..
#3 Cyl misfire..
Possible causes
Plugs, - Has been about 2 years since I replaced
Coil - Bought car new in 04, never replaced
Cat - never gave it a second thought
fuel injector - put techron by Chevron just about every oil change, I know I missed one here and there..
burned exhaust valve - say it aint so...
poor compression - I have to rent a tool...
defective computer - I don't think so..
Ford Super Duty (1999-2016) :: 2006 F250 - Misfire / Stutter On Hard Acceleration Under Load
06 250 5.4 40k on it, usually when cold and accelerating engine will misfire and stutter and then continue accelerating. The wrench light will flash sometimes but it wont store a code. This used to be vague in occurrence but has now started to be more a common occurrence even when up to normal operating temps.It seems only to misfire /stutter on hard acceleration or towing/hauling heavy loads. The only answer I got from a mech would be to do a computer reflash, not sure why /how this would fix whats going on.
View 1 RepliesCamry :: 2009 / 4 Cylinder - Check Engine Light And Sluggish Acceleration
My wife called to tell me that her Camry would barely pull away from a standstill this morning. Very sluggish until about 2500 rpm, at which point she said it took off normally. This accompanied by the Check Engine light, which just appeared this morning. I haven't been home yet to check fluid levels or take a test drive. Anything in particular I should be looking for?
View 6 RepliesCamry :: 2007 SE 4 Cyl - Car Seems To Lag Under Hard Acceleration
I have a 2007 Camry SE 4 cyl. Sometimes under hard acceleration the car seems to lag. I have about 64K miles on the car.
When is it recommended to have a spark plug replacement? Will a tune-up work to liven up the car a little better?
Camry :: 1998 / 4 Cylinder - Surging When Accelerating Hard And Hitting Just Over 4000 RPM
I have a Camry with 198K miles. When accelerating hard and hitting just over 4000 rpm the car will start surging. Letting off the gas and allowing the the automatic transmission to shift will stop the surging.
Will do this in any gear. The first few times the P1310 code came up but the last few times it did not throw any codes.
Also have the P0401 code which I have had for several years.
This is a very consistent problem which only occurs at just over 4000 rpms.
Just did some more testing and found that slowly revving the engine with car in Park will cause the same issue. When it gets to 4000 RPM it surges. Is there are rev limiter at 4000 rpm for some reason?
Camry :: 2005 LE - Misfire When Idling And Trying To Accelerate Hard / P0304 Code
We recently bought a used 2005 Camry LE 4cyl 2.4L. When we test drove it there were hardly any symptoms and no CEL. After driving it for a week we start feeling a stuttering every once in a while, no CEL still so I thought it might just need a tune up.
Replaced the plugs (which were in bad shape, were Iridiums, friend mentioned it seemed like they were burnt, white blistering like high RPM burn) with new NGK Platinums and replaced the air filter (was also in bad shape, was K&N that was badly clogged up and black).
Drove it around, let it idle, turn on AC, no problem not a hiccup. Next day arrives and the car is misfiring worse than before. CEL comes on too. We get the codes and its the P0304 I mention in the title.
We check the coils and the plugs and they fire, we switch coil 4 and 1 and clear the CEL, then later the CEL comes back on and it's still P0304 so we rule out the coils. The plugs come pre-gapped also.
The misfires are at their worst when idling and trying to accelerate hard, I can hold it at 2000-3000 RPMs with no hiccups or very few ones. Misfires worse with AC on.
Only thing left to do is check compression, try to clean the injector with fuel additive and premium gasoline, or replace the injector, at least that's what I think.
It has 86000 miles.
Camry :: 2005 SE V6 Engine Stumble On Hard Acceleration
I just bought an 05' SE V6, with the 3.3 engine. Seemed to run good, had it checked by shop and they said it was a good buy, so i bought it. First day I owned it, took it to toyota dealership and had them do a 90, 000 mi service. did a timing belt, water pump, tranny flush, oil change. I got the car back, and it ran like crap! It would stumble on hard acceleration, and seem to even surge a bit at times. I took it right back? Service rep tried to say I put in diesel or bad gas. I only filled up with chevron premium, which is only gas i ever use. I know how to put gas in my tank!
Any how, they checked timing belt and said it was right, but the timing gear needed to be changed because one tooth looked rounded off. That didn't work either, still stumbled on acceleration, but idled perfect @ 675 rpms. So now the serv. manager gets involved, says he wants me satisfied. they then drained all my gas, then re-fill it. then flushed out all injectors. then put in all new plugs and PCV valve. I did a pressure test of fuel system, said it was good. While they were changing the plugs, they did a complete 6 cylinder compression test and scope analysis, and it came back good, too! I pick it up cause i got to go back. It ran a lot better but still stumbles on hard acceleration on highway. drove 1250 miles back, didn't use a drop of oil.
I did notice when I got 100 miles the temp gauge dropped all the way down to second mark on cold for a little bit, but went back to normal temp and stayed there through the last 1100 miles(that scared me, so i watched temp gauge like a hawk). And the outside temp was @ 62 degrees when the temp dropped at 1200 ft. Elevation...maybe it got stuck and is ok? My CEL has never came on through all this, and it does work, I have made sure of that.
I bought this car from original owner, and they had engine and heads just replaced in 2008 at 44,000 miles at toyota dealership under warranty fot 10,000 dollars. i verified this with that dealership 3 times with 3 different reps at that dealership. old owner said he was having problems with engine stumbling, and took it in twice and dealership said it was ok each time, not throwing any codes and sent him away saying car was ok.
Camry :: 2007 SE V6 - Noise Heard Under Moderate To Hard Acceleration
I have a 2007 Camry SE V6. Under moderate to hard acceleration, it sounds like a deep throaty sound coming from where the intake/throttle body is located, almost as if I have a SRI, but I do not. I checked for anything loose, hoses, airbox, etc. Then checked the intake resonator below and to the left of the battery, all seemed normal. Everything seems normal! Only happens when I push the accelerator a little more than usual, for example, when I go on the highway.
View 6 RepliesFord F-150 (2004-2008) :: Cylinder 7 Misfire / Cylinder 6 Has Oil On Plug
06 F150 fx4 has cly 7 miss fire cly 6 has oil on plug .Check engine light comes on only if you step into the gas, The oil was low. If you drive normal the check engine light does not come on, but you can fill the miss when in gear. Change the plugs an coil add oil still no change.
View 4 RepliesToyota - Camry :: 1991 - Transmission Leak / Bumps Into Gear On Hard Acceleration
I have a '91 Camry that's my daily 50 mile round trip commute car. It runs well and still has lots of pep at 156,000. There are oil and tranny leaks (tranny leaks around the pan seal) but I check the levels and keep everything topped off. Tranny fluid and filter were changed about 20K miles ago. I am the original owner. Shifting is OK unless I accelerate hard, then it "bumps" into gear. On hard acceleration it is a pretty good bump but if I back off the gas it shifts much better. There are no other symptoms, at lower speeds it shifts fine unless the A/C is on, then I get bumps above the 1-2 shift. What the problem is?
View 3 Replies