Impala - Chevrolet :: 2000 3.8L V6 - Code P0300 Multiple Random Misfire
I have a 2000 Impala with a 3800 V6 series 2 with 165,000 miles. The only code I had was a P0300 Multiple random misfire that occured off and on at first, Worse in the city Better on Highway. It would start running on half the cylinders and bogged down, with the check engine light flashing, after getting onto the highway it would straighten itself out at first. I thought i had water in the gas so i ran some heat through it. straightened out for a day then happened again so I thought maybe a should run some premium gas in it, The car ran like total crap until the premium was gone, so i thought maybe it's running too rich, I put 87octane in it and it ran great for a day or two, then it gradually got worse to where it would not straighten up on the highway, tried to die at stoplights and i had to drive it with 2 feet to get it home and park it. I've replaced the battery, spark plugs, wires, ICM checked good, coil packs are good, replaced fuel Pressure regulator, looked for arcing on the spark plug heat shields and it will not start. It turns over but doesn't try to ignite and when I get the slightest rumble of ignition, it backfires up through the manifold and I see a puff of gas or light smoke by the exhaust manifold.
The car had a vacuum leak around the intake manifold cover gasket and a leak on the fuel rail. I pulled the fuel rail off my impala, snugged up the rest of the intake bolts then disassembled the fuel rail, flushed it out and cleaned the injectors the best i could, then reassembled it. before i re-installed the fuel rail I hooked it up to the fuel lines outside of the engine and tried to start the vehicle. all injectors had a nice spray pattern. So i installed the rail and it still didn't start but it had more combustion than before although it's still backfiring like before. Checked the fuel pressure by turning the key on and the fuel pressure went to zero very fast. I blew the rail out with air so to make sure i didn't damage the regulator I replaced it with the old one, ran the test again with same results, so i reinstalled the new regulator. I performed the fuel pressure test a few more times while moving the fuel hoses and when i moved the back supply line the vacuum loss stopped then dropped to zero when i let off of it. So I replaced the fuel line connector and O-rings on the injectors. It no longer has a vacuum leak.
I cleaned the EGR Valve out and had no luck there, then I removed the Idle Air Control Valve-pushed the pintle in, re-ionstalled it and WooHoo! it started! Although it still ran like crap with the same random misfire I was still happy to hear it start.I pulled the plugs on it to do a compression test and all 6 cylinders have between 180-190psi so the engine is in good condition mechanically. I installed new plugs before getting the car restarted and when i removed them for the test they were covered in thick black soot after running for roughly 15 minutes max.
I have (2) 2000 Chevy Impala's so I've swapped sensors from my wifes car to see if it would fix it. I've tested the following MAP, MAF, IAC, coil packs and ECM. None of these made the car change. I believe it is a timing chain because the car has never had a new timing chain and is way overdue, but I haven't had a code for a crankshaft position sensor. Can the timing chain be bad without throwing a code? It's not out of time enough to change the valve timing because I had a good compression test but its not firing right and still has the multiple random misfire. I have not checked or received a trouble code for o2 sensors, crankshaft position sensor or cam sensor. Something has the timing retarded and is dumping extra fuel into the engine because my new plugs looked like they were in the engine for a year.
Accent MC (2006-11) :: 2007 GLS - Random / Multiple Misfire And Code P0300
I have a 2007 Hyundai Accent GLS. I just got it from a used car dealership (local) and it runs perfectly. It had a misfire code when i first got it, for all cylinders plus the p0300. It went away when i started the engine again, and didnt come back til a month later (Now). now it wont go away.
I went to advance auto and had them use their OBD2 reader for a trouble code and i got p0300, p0301, p0303, p0304. No other codes present.
I am not feeling anything bad, and from what I am told, a misfire feels like a hard shift. This is of course after getting the plugs and wires changes as well as an oil change. Standard preventative maintenance.
The mechanic used OEM parts got from local parts shop. i think the OEM plugs are the copper ones. I would have preferred iridium as they arent that much more expensive but I don't want to pay for another plug change.
The only symptoms I can think of, is that according to google, I should get around 380 miles to a full tank (11.9 capacity, 32 mpg city). I am only getting 280 from full tank to gas light.
I have also gone through a lot of oil. I checked the dipstick and it was below the low line, so i bought a quart of high mileage oil (same exact brand and type of oil that i gave to the mechanic to use) and it went to just above the full line. This was at around 1500 miles after oil change.
After visiting multiple sites about misfires, i found a few things that caught my attention. One is a site called auto service professional, which talks about the OCV for the MC accent. A lot of sites also recommend gaping the plugs at .035.
Chevrolet - Avalanche :: 2003 - P0300 Code / Multiple Or Random Misfire?
My 03 Chev Avalanche is giving me a P0300 code (multiple or random misfire). With no distributor or individual coil is this something I can fix myself or is it shop time?
View 6 RepliesPassat (B5) :: Error Code 16684 And 16686 - Random / Multiple Cylinder Misfire
I was driving along and the engine started missing really bad. The whole car was bouncing around. At first I thought I had a flat, but when I stopped I noticed it was the engine. I checked the error codes and got 16684 and 16686 --- Random/Multiple Cylinder Misfire.
I had a problem recently with the vacuum hose broken and was causing an error code. Replace the hoses and it has been fine. Checked to make sure that the hoses were secure and they are fine. Doesn't seem to me to be related. So many problems for a car with 57,500 miles
Tiguan :: 2010 - Random / Multiple Cylinder Misfire Detected - MIL On
My buddy has a 2010 tiguan and hes having a misfire issue. It has a hesitation and the interior lights seem to dim with the hesitation. Heres the codes that pulled up with vagcom.
4 Faults Found:
000768 - Random/Multiple Cylinder Misfire Detected
P0300 - 000 - - MIL ON
Freeze Frame:
Fault Status: 11100000
Fault Priority: 0
Fault Frequency: 1
Reset counter: 255
Mileage: 148426 km
[Code] ....
What it might be?
Camry :: Car Shakes / Jerks When Shift Into Reverse Check Engine Light On - P2716 Code
I have run into a bit of a dilemma with my recently purchased 2010 Camry SE.
Whenever I shift into reverse, the car jerks or shakes for a moment. The engine light is also on.
Before, when I put the car into reverse,there'd also be a knock sound along with a vibration, but the engine light was never on.
Now today, when I put the car in reverse, the vibration/shake/jerk is VERY noticeable and the car almost rocks back and forth for a brief second when this happens and the Engine light stays on.
note that this only happens when I put the car into reverse.
Camry :: 2005 - Random Misfire And System Too Lean Code?
i have a 2005 camry 4 cyl. and i have a couple of code: second o2 sensor, system too lean, misfire cyl. 1 2 3 and 4. when i run the car it is incredible how much gas it take.
I first replace the second o2 sensor and i cleaned the maf sensor, air filter, iac and trhotle body but the codes came again.
Golf IV / Jetta IV :: VR6 - Random Multiple / Cylinder Misfire
Replaced my water pump March 2nd using the "From Below" method. Started the car after and the check engine light was on and water pump was no longer leaking. I drove the GTI to Advance (15 Mins away) it drove fine and I pulled two codes.
P0300 - Random Multiple/Cylinder Misfire
P0301 - Cylinder 1 Misfire
The car pulled and drove normally. The next day the car is misfiring badly. Hesitation and bucks when accelerating until roughly 3k then smooths out.
I will swap my coilpacks and check if the misfire moves as soon as I can get my hands on an OBD2 Scan Tool.
From what I understand about the VR6 :
-The water pump runs off the serpentine belt
-Camshaft timing is controlled by the timing chain.
-Timing chain is not affected by the serpentine belt/pulleys.
Questions :
-Can turning the Crankshaft Pulley affect timing?
-Can that be the cause of the misfire?
24V VR6
Passat (B5) :: Random / Multiple Cylinder Misfire Detected
What is going on with my sisters passat 2002 V6 GLX Auto 4Motion. Here is the codes:
16730-Camshaft Position Sensor (G163) Implausible Signal
P0346-35-00
16684-Random/Multiple Cylinder Misfire Detected
P0300-35-00
16688-Cylinder 4: Misfire Detected
P0304-35-00
16690- Cylinder 6: Misfire Detected
P0306-35-00
16689-Cylinder 5: Misfire Detected
P0305-35-00
I changed Both sensors and it still same problem. Car only has 40,000 miles didnt change timing belt.
Passat (B6) :: Random / Multiple Cylinder Misfire Detected?
my car was running fine yesterday. Today the check engine light came on and it started to run funny.. I checked the diagnostic code and it says the the cylinder is misfiring and that oxsygun sensor is malfunctioning. (Random/Multiple Cylinder Misfire Detected)
View 4 RepliesAccent MC (2006-11) :: Random / Multiple Cylinder Misfire Detected
I guess misfires are a rite of passage for these vehicles. I purchased it only a week ago. Welcome to Hyundai...
The car has 53k kms. It's throwing P0300 and P030X on all cylinders. There was one instance of P0128. The engine runs smoothly and doesn't seem to down on power, although I have nothing to compare it to. The only performance issue is that it acts as if there is a rev limiter at 6k rpm. It sputters and stops pulling above 6k. Strangely, it doesn't throw the codes under load. The light flashes while it's running steady-state.
I pulled the plugs and they appeared to be in excellent condition with no erosion of the electrodes. The ash is slightly more white than I would expect, making me wonder about it being excessively lean. I called the dealer. They told me that coils are problematic. Replacing the coils made no difference.
That lead me here. I found the thread "Check engine light flashes then stays solid," which referenced the ECM update.
Interestingly, of the codes mentioned on the TSB, the car is having all but the last two.
- P0300: Random/Multiple Cylinder Misfire Detected.
- P0301: Cylinder 1 - Misfire Detected.
- P0302: Cylinder 2 - Misfire Detected.
- P0303: Cylinder 3 - Misfire Detected.
- P0304: Cylinder 4 - Misfire Detected.
- P0128: Coolant Thermostat (Coolant Temperature Below Thermostat Regulating Temperature).
- P0328: Knock Sensor 1 Circuit High Input.
- P0461: Fuel Level Sensor A Circuit Range/Performance.
Golf IV / Jetta IV :: 1995 - Random Multiple Cylinder Misfire?
I have a 1999.5 Jetta VR6 12v, last week the car would not start. After some tests I determined the coil pack had gone bad. Replaced the Coil with a brand New aftermarket German made coil. Now 1 week later, driving at highway speed CEL came on, started to flash and obviously misfiring again. Ran Codes and now im getting these DTC's:
1)random multiple cylinder misfire detected p0300
2) cylinder 4 misfire detected p0304
3) ignition coil output 3 electric malfunction p1395
4) cylinder 3 misfire detected p0303
has this new coil gone bad already after a week?
New issue?
Plugs were replaced less than a year ago, wires were apparently replaced by previous owner about 2 years ago now. Crank sensor replaced less than a week ago...
Passat (B5) :: 2006 - Random / Multiple Engine Cylinder Misfire
I have a '06 Passat 3.6. I had the intake and valve cover off the other day and when I put it back together it started missing bad. The code it is throwing is a P0300/ random/multiple engine cylinder misfire. What is wrong?
View 2 RepliesFord F-150 (2004-2008) :: Multiple Codes - Random Misfire Detected
I have a 2005 F-150 W/ 5.4 triton, and am having multiple codes. They are:
P0172- System to rich(Bank 1),
P0174- System to lean(Bank 2),
P0300- Random misfire,
P0303- Cylinder # 3 misfire detected,
P0304- Cylinder #4 msfire detected.
Golf VI R :: Engine Error Codes - Random / Multiple Cylinder Misfire Detected
I recently found these codes. My car is APR 1+. The car seems to run fine so I'm not sure what is going on. I changed the plugs at ~60K miles and now have 72K miles.
Address 01: Engine (CRZ) Labels: 06F-907-115-CDL.clb
Part No SW: 5K0 907 115 M HW: 8P0 907 115 B
Component: 2.0l R4/4V TFSI 0020
Revision: 5BH20--- Serial number:
Coding: 0403010A180F0160
[Code] ....
Golf IV R32 :: CEL Start To Blink Then Stay On - Random / Multiple Cylinder Misfire Detected
I was driving the car normal with no problem. Got to a red light stop an as I was coming out of the red light the car started to hesitate a bit. So I start to drive home as I was driving home my check engine start to blink and then it stay on. When I got home and park the car I shut off ,then start it up again then the check engine light was off but the hesitation was still there. Then I got my computer and got the vagcom and got this code :
16684-random/multiple cylinder misfire detected
P0300-008- implausible signal
Buick - Lacrosse :: Oil Pressure Low Light Came On - Random / Multiple Cylinder Misfire Detected
2008 Buick Lacrosse CXL .. My son said the Oil pressure low light came on when he tried to start the car. It didn't want to start.
When I got there two hours later, it started but had a check engine light. But no low oil pressure light. Sounded like it was missing.
Code from computer came back P0300 "Random/Multiple Cylinder Misfire Detected". I cleared the code. Revved the engine to about 2000 RPM's and the CEL came back on.
Same code. When idling it feels like it's missing. The plugs look good, I am going to replace the ICM.
Lexus ES 2007-12 :: Random / Multiple Cylinder Misfire Detected - Error Codes On ES350
So on monday the following error codes appeared on my car. What needs to be replaced off the error codes?
P0300Random/Multiple Cylinder Misfire Detected2014-02-04 13:48:29
P0301Cylinder 1 Misfire Detected2014-02-04 13:48:29
P2030No Description Available2014-02-04 13:48:29
P3030No Description Available2014-02-04 13:48:29
C0033No Description Available2014-02-04 13:48:29
P0603Internal Control Module Keep Alive Memory (KAM) Error2014-02-04 13:48:29
C1400No Description Available2014-02-04 13:48:29
Elantra XD (2001-06) :: Random Misfire Code That Would Come And Go
We have been fighting a misfire code for about a year now and I'm pretty sure I finally found the cause. Last Spring the car died on the road and we had it towed to a local service center where they said the fuel pump was bad...this was the 2nd in about 2 years (previous owners doc). We had it replaced and the car was fine but as mentioned had a random misfire code that would come and go. In the last month the car has left us stranded several times and then started after a few hours or a day. While checking the connection to the fuel pump with a meter and test light I verified the pump was getting power correctly to the 5-pin connector but would not start. I unplugged the connector and the 1st 2 pins in the harness connector were damaged and probably burnt.
I cleaned it and applied dialectic grease and plugged it back in turned on the key...fuel pump primed and then the car started and ran fine. It then started to randomly turn on and off but not enough to stall the car. I wiggled the connector and the it I could make it run or shut off. Obviously the connector is bad and the contacts are intermittent. While driving the vibrations would move it just enough to make it cut on and off and more than likely cause a misfire code and sometimes stall the car. My problem now is I can't find a replacement connector/pigtail for the harness connector anywhere including the dealer. Where can I get a new connector for the 5-pin fuel pump harness connector? I have found a MAF replacement connector that looks very similar but not 100% sure if it's the same.