Toyota - Corolla - Fuel-economy :: 2005 - P0171 Check Engine Code / System Too Lean
I have an 05 Toyota corolla, and have the check engine light on, I scanned it at autozone and error code is P0171 - System Too Lean (Bank 1). Which shows following possible causes: Faulty MAF, O2, fuel injectors blockage etc. On recommendation from the guy in autozone, I added fuel additive to clean the fuel line/ injectors. The check engine light went away for 9 months. But it is back on again. Tried putting in fuel additive again but the light remains on.
View 5 RepliesCamry :: 2010 - Random Multiple Misfire / P2716 Code
I purchased a 2010 camry 4cyl. and i have this code of random multiple misfire, along with misfire on all 4 cyl. plus the P2716 code.
I had some issues with the fuel pump, got stuck, replaced it with a after market one, car did not run at all with it. So i decided to test the original one one more time. It worked, so i installed it back. The car starts just fine, takes off smooth, but when i get to 35-40 mph, the check engine light will blink, if i press the gas the engine will shake a little bit, and i can feel there is no power at the engine.
If i release the pedal for a moment and than press it again will run fine until i reach 35-40 mph. If it's in park, i pus the rpm up to 7k, engine runs just fine, no blinking check engine light, no engine shaking....
Like i said, 6 codes, 4 for each cylinder misfire, 1 for random multiple misfire, and p2716 solenoid....
Ford F-150 (2004-2008) :: Lean Condition Bank 1 And 2 / Random Misfire
2006 f-150 with a 4.6L. Its got 175k on the clock and ran like a sewing machine despite little maintenance other than oil changes. Recently it started running like crap; no power and missing so he borrowed a scanner and it was giving multiple codes. Here's what we have done so far, not necessarily in this order :
1.Checked for vac leaks with carb cleaner (this can be tough as engine runs crappy and hard to detect minor changes in rpms while your under the hood) no leaks detected yet
2. Changed the plugs, all looked good except for one which was heavily fouled and the electrode ate away mostly, I wasnt there and he doesnt remember which one but have a suspicion, more on that in a min
3. Changed most of the COPs and checked them all with a spark tester, all are firing.
4.Cleaned the MAF sensor with MAF cleaner
5. Checked back pressure on the exhaust by removing an upstream o2 sensor and holding a plastic fitting hooked to a pressure gage long enough to get a reading, about 1 lb idling to maybe 2 max when engine is reved, gage is not the best and fluctuates a 1/2 lb or so. Exhaust does not smell of rotten eggs.
6. Changed the fuel filter, it was terrible
7. Ran a bottle of Seafoam in the tank
8. Took the throttle body and egr valve off and checked for carbon stoppage, the holes in the egr were not blocked
9. checked the PVC valve and line and both elbows
7. checked the injector connectors with a noid light for signal, they all flash, checked the injectors them selves with a multimeter set for ohms, all about from 13.5-14.5. This should mean they arent fried but could they still be stopped up? They all sound like they are pumping when you listen with a mechanics stethoscope
9. Changed all 4 o2 sensors as this had never been done anyway
10. Compression check on cylinders, all within 10% of each other at about 180 lbs. When we pulled the plugs they all looked good except for # 7 which was heavily fouled ( I suspect the same on the original plugs) and again with a bad electrode, the part coming out of the porcelin. Intrestingly, this was an autolite plug, the rest were motorcraft, I hoped this was somehow just a bad plug but no change with a new MC plug
11. Changed the injector on #7
The scanner reads lean condition on banks 1 and 2 and random misfires on #4 and # 7 still. Per a troubleshooting tip online, we sprayed some carb cleaner in a small vac line coming off the manifold to induce a rich condition and the scanner showed the o2 sensors go to .900 which is what they are supposed to do per the guide. This means they are functioning correctly and a bonafide lean condition exists. I am leaning towards a vacuum leak around the plastic manifold under the aluminum one, maybe the gaskets but would like to rule out the egr valve, could it be the culprit?
I have even considered the possibility that the PCM is bad, though not likely. I have read to detect a vac leak you can hook the scanner up and spray the carb cleaner around on the manifold and lines with the scanner hooked up watching the scanner PID for the o2 sensors and when they detect the cleaner, they will hit that .800-1.0 meaning the engine sucked the cleaner in and you have found your leak. The exhaust smells rich. If it is a vac leak, you would think it should be a massive leak and not hard to detect, as crappy as the truck runs. I have searched the forums for days and exhausted about all I know to do.
Most important note: early on I suspected low fuel pressure as a possibility; with no schrader valve on the fuel rail and no easy spot to T into the system, we were scratching our heads how were gonna measure psi but the scanner reads absolute fuel rail pressure, gives about 40-43 psi. I hope the scanner is telling us what we need to know there, would prefer a mechanical gauge on the rail!
Passat (B5) :: 2001 - Emission Workshop / Misfire On 4 Cylinders And System Too Lean Codes
I am getting the dreaded emission workshop.
The codes i am getting are p0301-p0304 and p0171
Which are misfire on 4 cylinders and system to lean (bank 1).
Here is what I have done:
Got the 4 ignition coils replace, replaced the mass air flow, replaced the air filter, replace the plugs.
I just check the L wire and it doesn't have any cracks or holes
I don't know what to do next.
Golf IV / Jetta IV :: 2002 VW GTI - Misfire And Lean Code
I have a 2002 VW GTI, it's entirely stock and I can't get rid of this lean code. Compression is Good. Injectors are Good, Vacuum Limes are Good, Spark Plugs are Good, Coils are Good!!!!!. I only have two weeks to pass inspection in DE, I'm a college student and as most of us know, that mean $0 for car repair.
View 3 RepliesEngines - Repair :: 2005 Ford Freestyle - Lean Misfire
I have a 2005 SEL Freestyle with 114K miles. Cyl #3 missing. Has all the symptoms of a "lean misfire" - reading the code said #3. The indy mechanic already replaced the spark plug and the coil. Misfire still a problem. Tried to put some cleaner in there which did not work. He thinks the head needs to be replaced ....
The a/c is also busted. Needs a compressor. Not to mention I'm probably looking at brakes before much longer.
Ford F-150 - 1997-2003 :: 2002 - Cylinder Misfire And A Lean Code
My truck was running fine the past few days minus a cylinder misfire and a lean code the misfire was due to a coil pack being out no big deal on that part but yesterday on 7/30/13 my temp gauge turned off my truck wouldn't go below 1k rpms and then the over heating light came on. i drove the one mile home and turned it off an hour later i went back out to my truck to get to work and it refused to start.
I decided to just hold my foot down on the gas and crank it and it eventually started drove it to work with the same symptoms. now today its doing the same thing except now the truck is broke down in the parking lot at my job the engine is flooding cause i can smell it last night i changed the thermostat. I can get so that i can get my truck up in running its a 2002 f150 5.4L 4x4....
Camry :: 2005 LE - Misfire When Idling And Trying To Accelerate Hard / P0304 Code
We recently bought a used 2005 Camry LE 4cyl 2.4L. When we test drove it there were hardly any symptoms and no CEL. After driving it for a week we start feeling a stuttering every once in a while, no CEL still so I thought it might just need a tune up.
Replaced the plugs (which were in bad shape, were Iridiums, friend mentioned it seemed like they were burnt, white blistering like high RPM burn) with new NGK Platinums and replaced the air filter (was also in bad shape, was K&N that was badly clogged up and black).
Drove it around, let it idle, turn on AC, no problem not a hiccup. Next day arrives and the car is misfiring worse than before. CEL comes on too. We get the codes and its the P0304 I mention in the title.
We check the coils and the plugs and they fire, we switch coil 4 and 1 and clear the CEL, then later the CEL comes back on and it's still P0304 so we rule out the coils. The plugs come pre-gapped also.
The misfires are at their worst when idling and trying to accelerate hard, I can hold it at 2000-3000 RPMs with no hiccups or very few ones. Misfires worse with AC on.
Only thing left to do is check compression, try to clean the injector with fuel additive and premium gasoline, or replace the injector, at least that's what I think.
It has 86000 miles.
Tacoma :: P1071 Error Code - Bank 1 System Too Lean
I've searched for this and haven't come up with much other than the same error code for a bunch of other vehicles, and a bunch of different responses. My Tacoma is a 2000 PreRunner, 3.4 liter engine.
The exact code I get it is:
P1071
bank 1 system too lean
What this could be?
Passat (B5) :: 2001 - MIL Light On With DTC Code P0171 Lean System
I have a 2001 Passat 1.8T that has the pesky MIL light on with a DTC code P0171 lean system. I have sent it to the mechanic many times to no avail. What the mechanic did was replacement of the MAF, O2 sensors, checked intake manifold leak as well as exhaust manifold leak. His last attempt was to check for clogged injectors and fuel filter and they were in good condition. He says the ECM is bad. I was able to retrieve freeze frame data as well as live data which shows that the computer is compensating what it thought was lean by having very positive LTFT of 22.6. I don't believe the ECM is bad but cannot be sure. There is one more thing that was not checked by the mechanic is the EGR valve. Could that be the cause of my woes - the lean system?
View 14 RepliesPassat (B6) :: 2007 - Error Code Of P0171 System Too Lean
I have an 07 passat with a 2.0 4 cyl turbo and I have an error code of P0171 system too lean (bank1) but engine seems to run just fine, what this code means, am wondering if it is something I can fix or if it needs to go to the shop??
View 2 RepliesElantra XD (2001-06) :: Random Misfire Code That Would Come And Go
We have been fighting a misfire code for about a year now and I'm pretty sure I finally found the cause. Last Spring the car died on the road and we had it towed to a local service center where they said the fuel pump was bad...this was the 2nd in about 2 years (previous owners doc). We had it replaced and the car was fine but as mentioned had a random misfire code that would come and go. In the last month the car has left us stranded several times and then started after a few hours or a day. While checking the connection to the fuel pump with a meter and test light I verified the pump was getting power correctly to the 5-pin connector but would not start. I unplugged the connector and the 1st 2 pins in the harness connector were damaged and probably burnt.
I cleaned it and applied dialectic grease and plugged it back in turned on the key...fuel pump primed and then the car started and ran fine. It then started to randomly turn on and off but not enough to stall the car. I wiggled the connector and the it I could make it run or shut off. Obviously the connector is bad and the contacts are intermittent. While driving the vibrations would move it just enough to make it cut on and off and more than likely cause a misfire code and sometimes stall the car. My problem now is I can't find a replacement connector/pigtail for the harness connector anywhere including the dealer. Where can I get a new connector for the 5-pin fuel pump harness connector? I have found a MAF replacement connector that looks very similar but not 100% sure if it's the same.
Ford Fuel System :: 1988 - Got Code 41 - Lean Miss At Idle - ECM Or Injectors?
1988 F250 351 5.8
I've worked for months on this truck and I now have it in the shop. The truck shows a 41 code and has a lean miss at idle that get worse during acceleration and cruise. The injectors were refurbished 6 months ago and the ECM was replaced 3 months ago. All sensors are new and within specs. Fuel pressure is good and there are no vacuum leaks.
The mechanic has verified that the condition is not electrical related. The O2 sensor will react if carb cleaner is sprayed into the throttle but other wise shows constantly lean. He's now checking all pins at the computer for any off condition. He is suspicious of the refurbished injectors. I'm wondering if the computer somehow went out again. Which way to go or what/how next to test?
Passat (B5) :: Check Engine Light Came On - Code P0171 / Fuel System For Bank 1 Was Too Lean
We have a 2003 Passat 1.8t. Had the Check engine Light come on. Went down to AutoZone and hookeded up the OBDII reader. Came up with P0171, Fuel System for Bank 1 was too lean. Probable causes:
1. Fuel Pressure of MAF (If Bank 1 & Bank 2 set codes together)
2. O2 Sensor
3. Ignition Misfire
4. Fuel Injector Problem
Car has 60K - has always run well. Wife says she thinks it's running a bit sluggish. I rarely drive the car, but I think she's right. Car is not missing or running rough.
I cleared the code & started the engine; Check Engine Light is off; then looked at the codes and I find a P0171 (Pending). She tells me that the light has been on before & then gone away. So I guess it clears itself, but eventually comes back.
Accent LC (2000-05) :: Check Engine Light Error Code P1128 / Too Lean Intake System
This is the infamous error code many Accent owners might have experienced it. The code refers to "Too lean intake system". People try to replace all kinds of parts like ECM, MAF, O2 Sensor, TPS, Fuel Pump, Fuel Filter, etc. according to my research. I just bought a 2001 Accent and the P2188 light came on. I wrote an email to Hyundai Corp. Asking what would be the most likely part that will cause the (P2188) check engine light to come on.
View 3 RepliesTrailBlazer :: Random Misfire And Code P0300 - Rough Idle
'02 TB w/ code P0300 / Random misfire. Started the other day when it was very damp out, FWIW. Feels like ur driving on rumble strips during acceleration. Rough idle also. It does not do this continually though as after a while (minute) it clears up and runs smooth for a while then runs rough & light will again for a while. I seafoamed it today since it been about 60k since last seafoam. I thought that might have worked until I drove about 20 mile and it went rough again. I also cleaned the oil out of the cam sensor elect connector, since that caused rough running before, although it didn't throw that code. It seems to be very intermittent. '02 TB, 185k miles, orig plugs changed at 125k. Is it actually just going in & out of a limp-mode? O2 since it's random ???
View 14 RepliesPrius (Gen 2) :: P0300 Code And Random Misfire - Car Shaking More Than Usual
Recently i started the car and it was shaking more that usual. the CEL light came stating P0300 with random misfires. It sounds and feels like misfires so i believe this is true.
View 10 RepliesGMC - Sierra :: 2004 - Code P0300 Random Misfire While Under Load
2004 GMC Sierra 2500 HD, 227,000 miles 6.0L V8.
While driving up hills or increasing load, the CEL will flash multiple times, I pull over as I know CEL flashing is not good. I turn the truck off, allow it to sit for a few minutes, whip out the code scanner, only code that was there happens to be P0300. Truck has poor MPGS, idles rough, loss of power. this happens every time I drive this vehicle as I use this truck to pull my trailer that weighs around 4000 lbs. Problems come and go. Some days I can drive the truck for an hour with no problems, come up to a red-light, BAM, CEL is flashing, truck is bouncing side to side due to the poor idle, other days this happens while sitting in the parking lot of my job with the ac on.
Truck has been to the shop several times as I'm no mechanic. Parts replaced are as follows:
- Fuel pump
- Throttle Body
- All plugs
- All wires-All Coils
- Intake Manifold Gasket-
- Battery
- Sensor 1 Bank 1 O2 Sensor
- Sensor 1 Bank 2 O2 sensor
Santa FE SM (2001-06) :: 2004 3.5L V6 - Random Misfire Code P0300
I have a 2004 Hyundai Santa Fe 3.5L V6 when i was driving a couple of days ago the check engine light flashed and after a while it stayed on the codes are P0300 which is a random misfire as well as a misfire in cylinder 2, 4 and 6
I replaced all 6 spark plugs and the 3 spark plug wires still the same issue. The car hesitates when accelerating when i accelerate it looks like it wants to stop the rpm goes to almost zero and then it moves and so on. the rpm goes up and down like crazy.
Sometimes it won't move past 1000 rpm I'm moving 60mph and still on 1000rpm and sometimes it works just fine like there is no issue at all. When idle the car is fine and everything seems normal it stays on 900rpm. The car has 158K miles on it.
I uploaded a video to show you what's happening to the tachometer when I accelerate [URL] ....
I'm on a limited budget I'm thinking of changing the ignition coils but i want to make sure that's what is causing the problem first because i spent 200$ to change spark plugs and wires and the mechanic didn't fix the issue.